Viking Cordless Telephone K 1900 User Manual

K-1900 Series  
TECHNICAL  
Hot Line Phones  
Practice  
June 27, 2002  
TELECOM SOLUTIONS FOR THE 21ST CENTURY  
Economical and Vandal Resistant  
Hot-Line Phones  
The K-1900 Series of Hot-Line phones are pro-  
grammable to dial a 1-20 digit telephone number  
each time the phone’s handset is lifted. The prod-  
K-1900-6  
ucts may be programmed to Touch Tone  
or pulse dial and will not dial on incoming  
calls.  
K-1900D-2 ASH  
K-1900-7  
The K-1900 Series phones are available  
in a desk or wall chassis, as well as in a  
vandal resistant panel phone configuration. A  
network insert dialer is also available, to convert  
standard phones into hot-line phones.  
K-1900W-2  
K-1900W-2 ASH  
K-1900D-2  
Applications  
• Catalog sales  
Features  
• Information kiosks in malls  
• Courtesy and customer service phones  
• Automated tellers  
Telephone line powered  
• Hearing aid compatible amplified handsets  
• Rotary handset volume control  
• 1 - 20 digit programmable speed dial number  
Touch Tone and 10/20 pps pulse dialing  
• Non-volatile E2 memory (no batteries  
required)  
• Hot-line reservation phones  
• Replace leased Ringdown circuits  
• Security and emergency phones (pools, etc.)  
• Restricts fraudulent calls from hand held  
dialers  
Phone...715.386.8861  
m
onics.co  
ingelectr  
K-1900D/W-2 available in red or ash  
• Optional Q170600 ringer (Fax Back Doc 845)  
• Operates on a C.O. line or analog PABX/KSU  
extensions  
info@vik  
• Ring detection (will not dial on incoming calls)  
• Programmable security code to enter  
programming mode  
Touch Tone programmable  
K-1900-6 fits standard 500, 554, 2500 and  
2554 set phones  
Specifications  
Power: Telephone line powered (20V DC/18mA minimum)  
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95%  
non-condensing humidity  
Dimensions: (see page 2)  
Dialing Speed: Normal - 120ms tones/10 pps, Fast - 50ms  
tones/20 pps  
 
Programming  
While in the programming mode, two beeps indicate a valid programming entry. An invalid entry will be indicated with three  
beeps. To exit programming, simply hang-up the K-1900 Series phone.  
A. Accessing the Programming Mode  
1. Using the Security Code  
Step 1. Connect the K-1900 Series device to an analog C.O. line, or an analog PABX/KSU station.  
Step 2. From a Touch Tone phone, call into the K-1900 Series phone.  
Step 3. Listen for at least one ringback in the calling phone and then take the K-1900 Series phone off-hook (answer the  
phone).  
Step 4. From the Touch Tone phone, enter your six digit security code (factory set to 845464 - see section E).  
Step 5. A double beep indicates the K-1900 Series phone is in the programming mode (see sections B-G ). If six digits are  
entered and no beeps are heard, an incorrect security code has been entered. Repeat steps 2-5 or follow directions  
in 2. Without a Security Code below.  
2. Without a Security Code (If You Have Forgotten or Lost the Security Code)  
Step 1. Remove JP1 (as shown to the right). For the K-1900W-2 and K-1900D-2, the  
plastic cover must be removed to expose the circuit board.  
Step 2. Connect the K-1900 Series device to a C.O. line, analog PABX/KSU station or  
JP1  
to a DLE-200B Line Simulator.  
Remove to  
Step 3. From a Touch Tone phone, call into the K-1900 Series phone.  
enter program-  
ming without a  
security code.  
Step 4. Listen for at least one ringback in the calling phone and then take the K-1900  
Series phone off-hook (answer the phone).  
Step 5. A double beep indicates the K-1900 Series phone is in the programming mode  
(see Programming sections B-G).  
Note: JP1 MUST be in place for  
normal operation.  
Step 6. When programming is finished, replace JP1 and replace cover on phone.  
Memory  
Location  
B. Quick Programming Guide  
then  
Enter Digits  
Speed dial number (see section C) 1-20 digits or pauses ............................................. phone number then  
#0  
#9  
Security Code, factory set to 845464 (see section E) ................................................... 6 digits  
then  
✱✱  
To add a anywhere in the dialing string .....................................................................  
To add a # anywhere in the dialing string ...................................................................... #  
To set dialing speed to normal - 120ms tones/10 pps (factory setting) .......................... 1  
To set dialing speed to fast - 50ms tones/20pps ........................................................... 2  
To restrict Touch Tone user dialing (factory setting) ...................................................... 3  
To enable Touch Tone user dialing ................................................................................ 4  
Toggles between pulse and Touch Tone dialing (see section C) ................................... 6  
To add a 4 second pause anywhere in the dialing string (see section C) ...................... 7  
To add a 1 second pause anywhere in the dialing string ............................................... 8  
C. Programming Examples  
Step 2 - Enter Digits  
To Program the ACD-10 to...  
Step 1 - See section A  
Enter Programming  
Enter Programming  
Enter Programming  
Enter Programming  
Enter Programming  
Enter Programming  
5551234 + #0  
...to Touch Tone dial 555-1234  
6 5551234 6 9 + #0  
...to pulse dial 555-1234 followed by a Touch Tone 9  
...to dial a 9, a 4 second pause and then 555-1234  
...to set the dialing speed to fast  
9 7 5551234 + #0  
2  
4  
#0  
...to enable unlimited user dialing after the phone has speed dialed  
...to clear the speed dial number or disable speed dialing  
D. Touch Tone and Pulse Dial Speeds  
The K-1900 Series phone can be programmed to dial at normal or fast dialing speeds. While in the programming  
mode, enter 1 for normal dialing speed - 120ms on/off Touch Tones or 10 pps pulse dialing. Enter 2 for fast dialing  
speed - 50ms on/off Touch Tones or 20 pps pulse dialing.  
 
E. Security Code  
A six digit security code is required to access the programming mode. The factory set security code is 845464 (V-I-K-  
I-N-G). It is recommended that you change the security code to a personal 6 digit (0-9) number in memory position #9  
while in the programming mode. Note: The security code must be six digits in length and cannot contain a or #.  
F. Touch Tone or Pulse Dialing  
The K-1900 Series phones are factory set to automatically dial using Touch Tones. A 6 entered in the speed dial num-  
ber will toggle the dialing mode between Touch Tone and pulse (see section C).  
Note: You can NOT program a and # to be pulse dialed.  
G. Touch Tone User Dialing Restriction (factory enabled)  
The K-1900 Series phones is factory set to restrict fraudulent calls from hand held pocket dialers. After speed dialing,  
the K-1900 Series phones will restrict (hang up) when they detect any Touch Tone that they did not generate. To restrict  
user dialing, enter 3 while in the programming mode. To enable user dialing, enter 4 while in the programming mode.  
Adding an Internal Ringer  
.47 mF @ 250V  
(included with ringer)  
An optional Q170600 internal ringer is available. For more informa-  
T
tion, retrieve Fax Back Document 834.  
R
Q170600  
Electronic Ringer  
Related Products  
Install Your Viking Product in a Weatherproof Enclosure  
The VE-9x12 and VE-9x20 provide the ultimate in  
weather protection for your Viking product!  
Weatherproof  
Enclosures  
The enclosures are constructed of cast aluminum and is  
made for years of outdoor service. The heavy-duty alu-  
minum door is labeled “Telephone” and has a gasket  
seal to keep out even the harshest weather. The VE-  
9x12 and VE-9x20 are available in two high visibility col-  
ors: safety yellow or emergency red.  
For more information on the VE-9x12 or VE-9x20,  
retrieve Fax Back Document 413.  
K-1900-8  
Shown with VE-5x10  
Vandal Resistant Hot-Line Panel Phone with Touch Tone Keypad  
The K-1900-8 Stainless Steel Panel Phone features a built-in Hot-Line dialer as well as a weather resist-  
ant keypad. The dialer can provide both Touch Tone dialing as well as 10/20 pps pulse dialing. After the  
phone number has been dialed, the Touch Tone keypad is enabled to permit additional manual dialing.  
The K-1900-8 housing consists of a heavy gauge, stainless steel panel, a metal Touch Tone keypad, an  
armored cable, and an all metal cradle for both weather and vandal resistance.  
For more information on the K-1900-8 Hot-Line Panel Phone, retrieve Fax Back Document 312. For  
more information on the VE-Series Surface Mount Boxes, retrieve Fax Back Document 424.  
Product Support Line...715.386.8666  
Fax Back Line...715.386.4345  
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or  
subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate  
such changes.  
Fax Back Doc 360  
Printed in the U.S.A.  
ZF300950 Rev G  
 

Tektronix TV Cables OA 5000 User Manual
THB Bury GPS Receiver CC 9010 User Manual
Thermaltake Power Supply 800W User Manual
TOA Electronics Portable Speaker H 3 User Manual
Toastmaster Oven XO 1MSS User Manual
Troy Bilt Blower TB180b User Manual
ViewSonic Projector VS11334 User Manual
Viking Personal Computer 16MB Memory Module HI4011 User Manual
Vornado Electric Heater IR400 User Manual
Weber Gas Grill 41996 User Manual