Viking Personal Computer 16MB Memory Module HI4011 User Manual

4. Locate the two memory expansion slots in the open compartment.  
Notice the location of the off-center keys on the expansion slots. There  
may be a standard memory module already occupying one or more of the  
expansion slots. If you  
need to remove an exist-  
ing memory module  
Viking Memory  
I N S T A L L A T I O N G U I D E  
HITACHI®  
VisionBook Plus & VisionBook Pro  
before continuing with  
this upgrade, please pro-  
ceed to step 5. If you do  
not need to remove a  
memory module, please  
proceed to step 6.  
5. To remove a memory mod-  
ule, locate the retaining clips  
on both sides of the module.  
Gently pull both clips away  
from the module. Then lift the  
module out of its expansion  
slot.  
6. To install a memory module,  
insert the module into the expan-  
sion slot at an angle and then push  
it down until it clicks into place.  
To be certain that the module is  
installed correctly, ensure that the  
off-center notch on the module is  
aligned with the off-center key of  
the expansion slot. The module  
can only be installed one way due  
to the position of the notch.  
Manual No. 1005210 • Release 05/98, Rev. B  
S P E E D  
P O W E R  
P E R F O R M A N C E  
The Hitachi VisionBook Plus comes standard with 16MB of removable  
memory. It can be expanded to a maximum of 128MB by installing the  
following Viking Components memory options into its two available  
expansion slots.  
The Hitachi VisionBook Pro comes standard with 16MB of memory sol-  
dered or 32MB (16MB soldered + 16MB memory module). It can be  
expanded to a maximum of 144MB by installing the following Viking  
Components memory options into its two available expansion slots.  
7. Replace the memory expansion cover and be sure to secure its holding  
screw.  
Description  
Viking P/N  
8. Replace the battery back into its compartment.  
8MB Memory Module  
16MB Memory Module  
32MB Memory Module  
64MB Memory Module  
HI4010, RHI4010  
HI4011, RHI4011  
HI4012, RHI4012  
HI4013, RHI4013  
9. Replace the AC power supply and any other cables you may have dis-  
connected.  
10. Turn unit right-side up and turn the system on. The computer auto-  
matically detects the added memory and gives the following error mes-  
sage: “Warning, Unexpected Amount of Memory, run SCU.” Go to BIOS  
Setup, Save and Reboot. The new memory can be verified during the  
POST routine at start-up and at the SETUP utility.  
The installation is now complete.  
WARRANTY & DISCLAIMERS:  
Caution:  
Electro Static Discharge (ESD) can damage electronic components. Before  
touching the memory module, ensure that you are discharged of static elec-  
tricity by touching a grounded metal object.  
All Viking Components products have been thoroughly tested free of defects in materi-  
al and workmanship. If any malfunction should occur while using one of our products  
in its recommended environment, Viking, at its option, will repair or replace the prod-  
uct at no charge, provided the product or any part thereof has not been abused, misused,  
neglected, replaced, repaired or modified. Viking shall make the final determination as  
to the existence and the cause of any defect. Viking will not repair or replace products  
designated as having a “Limited Lifetime” which fail solely because their estimated life  
has expired. No warranty is made with respect to customer products produced to orig-  
inal purchaser specifications except as specifically stated in writing by Viking.  
INSTALLATION INSTRUCTIONS:  
1. Turn the computer off and disconnect the AC power supply and any  
other cables from the unit.  
Note: If the unit appears to be powered  
down, ensure that it is not in Suspend mode.  
All shipping costs shall be the responsibility of the purchaser.  
Except as provided herein, there are no express or implied warranties of merchantabili-  
ty or fitness for a particular purpose. Under no circumstances will Viking Components  
be liable in any way to the purchaser for any damages, including but not limited to lost  
revenue, lost wages, or any other incidental or consequential damages arising out of the  
use of or inability to use this product. Viking reserves the right to make modifications  
in both hardware and software without prior notifications.  
2. Turn the computer upside-down. Remove  
the battery from the system. If you are not  
familiar with this procedure, please refer to  
your computer’s “Owner’s Manual.”  
3. Locate the memory expansion cover towards  
the front of the bottom panel. Also locate the  
holding screw on the cover. Remove the screw  
with a small Phillips-head screwdriver. Then  
remove the cover by lifting it up.  
All Viking Components are 100% guaranteed compatible with the OEM machines for  
which they are designed. All OEM's names, trademarks and part numbers are used for  
identification purposes only, and in no way imply that any of our products are original  
equipment parts.  
Hitachi, VisionBook and Traveler are registered trademarks of Hitachi PC Corporation.  
Copyright 1998 Viking Components, Inc.  
 

Texas Instruments Stereo Receiver DEM DAI3793A User Manual
The Singing Machine Karaoke Machine SML283BK P BL User Manual
Toshiba DVD VCR Combo SD KV550SU User Manual
Toshiba Flat Panel Television 13A26 User Manual
Tripp Lite Switch B021 000 19 User Manual
Uniden Two Way Radio uh095sx User Manual
Universal Power Group Battery Charger Jump Starters User Manual
Vermont Casting Indoor Fireplace DVT38S2 User Manual
VTech Telephone MI6820 User Manual
Waring Juicer JEX328 User Manual