COMPLIANCE INFORMATION
UL Listed
1000BASE-TX to 1000BASE-SX/LX
C-UL Listed (Canada)
CISPR/EN55022 Class A
EN55024
Media Converters
SGETF10xx-100
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
USER’S GUIDE
TRANSITION Networks SGETF10xx series Gigabit Ethernet™ media converters
connect 1000BASE-TX shielded or unshielded twisted-pair copper cable to
1000BASE-SX or 1000BASE-LX multimode or singlemode fiber-optic cable.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
1000BASE-T Copper
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.
1000BASE-SX/LX Fiber
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées
SGETF1013-100
SGETF1018-100
Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 850 nm 1000BASE-SX multimode
fiber-optic cable.
Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) MT-RJ
connector to 850 nm 1000BASE-SX
multimode fiber-optic cable.
SGETF1014-100
SGETF1025-100
Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 1300 nm 1000BASE-LX singlemode
fiber-optic cable.
Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) MT-RJ
connector to 1300 nm 1000BASE-LX
singlemode fiber-optic cable.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG
zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
SGETF1015-100
Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 1300 nm 1000BASE-LX singlemode
fiber-optic cable.
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
SGETF10xx in the Network . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . . . .4
Fault Isolation and Correction . . . . .5
Cable Specifications . . . . . . . . . . . . .6
Technical Specifications . . . . . . . . . .7
Compliance Information . . . . . . . . . .8
SGETF1017-100
Copyright Restrictions
© 2001 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 1550 nm 1000BASE-LX singlemode
Printed in the U.S.A.
33197.C
fiber-optic cable.
Install Cable
CABLE SPECIFICATIONS
Fiber Cable
COPPER
NOTE: The SGETF10xx series media converter auto-negotiation feature
allows the media converter to bring up the copper link in the highest
mode possible for ALL the attached network devices.
MULTIMODE
Fiber Optic Cable Recommended:
Optional:
62.5 / 125 µm multimode fiber
100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
850 nM
1.
Locate or build 1000BASE-TX-compliant cables with male RJ-45
connectors installed at both ends.
SGETF1013
2.
Connect RJ-45 connector at one end of cable to media converter
RJ-45 port connector.
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
Typical Maximum Cable Distance*:
SGETF1018
min: -10.0 dBm
min: -17.0 dBm
7.0 dB
max: -4.0 dBm
max: -0.0 dBm
3.
Connect RJ-45 connector at other end of cable to 1000BASE-TX-
compliant device RJ-45 port connector.
220 meters
850 nM
Fiber Optic Transmitter Power:
Fiber Optic Receiver Sensitivity:
Link Budget:
min: -9.5 dBm
min: -17.0 dBm
7.0 dB
max: -4.0 dBm
max: -0.0 dBm
FIBER
1. Locate or build 1000BASE-SX/LX-compliant fiber cable with male
two-stranded TX to RX connectors installed at both ends.
Typical Maximum Cable Distance*:
220 meters
SINGLEMODE
Fiber Optic Cable Recommended:
SGETF1014
9 µm singlemode fiber
1300 nM
TX
TX
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
min: -13.0 dBm
min: -20.0 dBm
7.0 dB
max: -3.0 dBm
max: -3.0 dBm
RX
RX
Typical Maximum Cable Distance*:
SGETF1015
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
5 kilometers
1300 nM
min: -5.0 dBm
min: -20.0 dBm
15.0 dB
2. Connect cable with connector installed at TX location on media
converter to RX location on attached device.
max: -0.0 dBm
max: -3.0 dBm
3. Connect cable with connector installed at RX location on media
converter to TX location on attached device.
Typical Maximum Cable Distance*:
SGETF1017
25 kilometers
1550 nM
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
min: -3.0 dBm
min: -23.0 dBm
20.0 dB
max: -2.0 dBm
max: -3.0 dBm
Power the Media Converter
1. Install power adapter cord at back of media converter.
Typical Maximum Cable Distance*:
SGETF1025
65 kilometers
1550 nM
2. Connect power adapter plug to AC power.
Fiber-optic Transmitter Power:
Fiber-optic Receiver Sensitivity:
Link Budget:
min: -9.5 dBm
min: -20.0 dBm
20.0 dB
max: -3.0 dBm
max: -3.0 dBm
3. Verify that media converter is powered by observing illuminated
LED(s).
Typical Maximum Cable Distance*:
65 kilometers
*Actual distance dependent upon physical characteristics of network installation.
Copper Cable
Category 5 twisted-pair copper wire is required. Either shielded twisted-pair (STP) or
unshielded twisted-pair (UTP) can be used. DO NOT USE FLAT OR SILVER SATIN WIRE.
CATEGORY 5:
Gauge
24 to 22 AWG
Attenuation
Maximum Cable Distance:
22.0 dB /100m @ 100 MHz
100 meters
The Gigabit Ethernet™ network uses all four wire pairs. The active pairs are pins 1 & 2,
pins 3 & 6, pins 4 & 5, and pins 7 & 8. Use only dedicated wire pairs (such as blue/white
& white/blue, orange/white & white/orange) for the active pins. NOTE: Straight-
through/crossover configuration is automatic.
OPERATION
FAULT ISOLATION and CORRECTION
If the media converter fails, isolate and correct the fault by determining the
answers to the following questions and then taking the indicated action:
Using Status LEDs
Use the status LEDs to monitor media converter operation in the network.
1.
Is the P(o)W(e)R LED on the media converter illuminated?
P(o)W(e)R Steady LED indicates connection to
NO
•
external AC power.
Is the power cord properly installed in the media converter and at
the external power source?
PWR
RXF
(Fiber receive) Flashing LED
indicates reception of data on fiber
link.
•
•
Does the external power source provide power?
Contact Technical Support: (800) 260-1312.
LKF
LKC
RXF
RXC
YES
•
LKF
RXC
LKC
(Fiber link) Steady LED indicates
fiber link connection.
Proceed to step 2.
2.
3.
Is the LKC LED on the media converter illuminated?
(Copper receive) Flashing LED indicates reception of data on
copper link.
NO
•
•
•
Check twisted-pair cables for proper connection.
Check twisted-pair cables for connection of all four pairs.
Contact Technical Support: (800) 260-1312.
(Copper link) Steady LED indicates copper link connection.
YES
•
Proceed to step 3.
Is the LKF LED on the media converter illuminated?
NO
•
Check fiber cables for proper connection.
•
Verify that TX and RX cables on media converter are connected to
RX and TX ports, respectively, on other device.
Contact Technical Support: (800) 260-1312.
•
YES
•
Proceed to step 4.
4.
Is the RXC LED on the media converter flashing?
NO
•
•
If there is NO ACTIVITY on the 1000BASE-TX port, proceed to step 5.
If there is ACTIVITY on the 1000BASE-TX port, disconnect and
reconnect the 1000BASE-TX cable to restart the initialization process.
Restart the workstation to restart the initialization process.
Contact Technical Support: (800) 260-1312.
•
•
YES
•
Proceed to step 5.
5.
Is the RXF LED on the media converter flashing?
NO
•
•
If there is NO ACTIVITY on the 1000BASE-SX/LX port, continue
below
If there is ACTIVITY on the 1000BASE-SX/LX port, disconnect and
reconnect the fiber cable to restart the initialization process.
Restart the workstation to restart the initialization process.
Contact Technical Support: (800) 260-1312.
•
•
YES
•
Contact Technical Support: (800) 260-1312.
|