SECTION 1 GENERAL DESCRIPTION
IMPORTANT SAFEGUARDS
1. Read Instructions
INSTRUCTION MANUAL
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety instructions and instruction manual should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the instruction manual should be adhered to.
4. Follow Instructions
CCD COLOR CAMERA
All operating and use instructions should be followed.
5. Cleaning
IK-6200A/IK-6400A
Disconnect this video product from the power supply before cleaning.
6. Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Please read this manual thoroughly before use, and keep it
handy for future reference.
7. Water and Moisture
Do not use this video product near water-for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
8. Accessories
Do not place this video product on an unstable cart, stand, tripod, bracket or table. The
video product may fall, causing serious injury to a child or adult, and serious damage to the
product. Use only with stand, tripod, bracket, or table recommended by the manufacturer, or
sold with the video product. Any mounting of the product should follow the manufacturer’s
instructions, and should use a mounting accessory recommended by the manufacturer.
9. Ventilation
This video product should never be placed near or over a radiator or heat register. This
video product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s instructions have been adhered
to.
10.Power Sources
This video product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your location, consult your
product dealer.
11. Power-Cord Protection
Power-Supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular attention to cords at plugs, screws
and the point where they exit from the product.
12.Lightning
For added protection for this video product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the power supply and cable system. This will prevent damage to the video product due to
lightning and power-line surges.
13.Overloading
Do not overload power supply and extension cords as this can result in a risk of fire or
electric shock.
14. Object and Liquid Entry
The CAUTION label, shown on the left, is
attached on the bottom of camera.
Never push objects of any kind into this video product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electrical shock.
Never spill liquid of kind on the video product.
15.Servicing
The lightening flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
16.Damage Requiring service
Disconnect this video product from the power supply and refer servicing to qualified service
personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
d. If the video product does not operate normally by following the operating instructions in
the instruction manual. Adjust only those controls that are covered by the instruction
manual as an improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the video product to its normal
operation.
e. If the video product has been dropped or the cabinet has been damaged.
f. When the video product exhibits a distinct change in performance-this indicates a need
for service.
WARNING:
CAUTION
CONNECT 24V AC UL LISTED
CLASS 2 POWER SUPPLY.
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
17. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer with the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
FIELD INSTALLATION MARKING:
WORDED : THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO ALL LOCAL CODES.
18. Safety Check
Upon completion of any service or repairs to this video product, ask the service technician
to perform safety checks to determine that the video product is in proper operating condition.
Note : The camera is indoor used
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses , and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipmetn in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
USER-INSTALLER CAUTION :Your authority to operate this FCC verified equipment
could be voided if you make changes or modifications not expressly approved by the
party.
1-1
5. AUTOMATIC ELECTRONIC SHUTTER (AES)
7. NOTES ON USE AND INSTALLATION
Exposure time is controlled automatically within a range of 1/60 sec. to 1/
100000 sec. to obtain an adequate signal when the back panel switch is
turned to AES.
Do not aim the camera at the sun
Do not aim the camera at the sun or point it at sun even if you are not
shooting.
Do not shoot intense light
Intense light such as a spotlight may cause a bloom or smear. A vertical
stripe may appear on the screen. However, this not a malfunction.
When the back panel switch is turned to VIDEO or DC, the exposure time is
fixed 1/60 sec.
Treat the camera with care
Do not drop the camera or subject it to strong shock of vibration. Otherwise,
the camera may malfunction.
Never touch internal parts
Do not touch the internal parts of the camera other than the parts specified.
Otherwise, the camera may malfunction.
6. BACKLIGHT COMPENSATION (BLC)
Do not splash water on the camera
This function is activated when the BLC switch is set to on.
Install the camera where the camera can be kept dry. If the camera gets
wet, turn off the power and contact your dealer.
ON
OFF
Install the camera
Where no video noise appears
If cables are wired near electric lighting wires or a TV set, noise may appear
in images. In this event, relocate cables or reinstall equipment.
BLC
When the automatic electronic iris and the auto iris lens is used, the exposure
adjustment is automatically performed so that a best picture is obtained at a
monitor zone of about 60% in horizontal and about 60% in vertical direction.
Check the ambient temperature and humidity
Avoid using the camera where the temperature is hotter or colder than
specified. Otherwise, the quality of images may deterlorate or internal parts
may be affected. Special care is required to use the camera at high
temperature and humidity.
This function is effective when a strong light enters the portion other than this
zone and auto iris lens closes and darkens the area to view.
Should you notice any trouble
If any trouble occurs while you are using the camera, turn off the power
and contact your dealer. If you continue to use the camera when there is
something wrong with it, the trouble may much worse and an unpredictable
accident may occur.
(Monitor screen)
50%
50%
8. IN CASE OF PROBLEMS
9. PART NAMES & FUNCTIONS :
Condition
Check Point
Are the camera and connected equipment turned on?
Is the iris of the lens adjusted properly?
Are cables connected correctly?
No image
Is the monitor TV adjusted correctly?
Is the lighting too weak?
Note
Unnatural color
When external light and internal light are mixed or when the
object includes some chromatic colors are shot, a hue may
partly have a little difference.
5 0
1-3
10. CAMERA INSTALLATION GUIDE
Wall
9.5mm
Camera Installation Guide
1/4"-20UNC
112
15
The Installation Guide is for reference only.
Bracket is not be enclosed.
EIM-0010325
4/26/2000
1-4
|