1
English
Table of Contents
Usage Notice
Precautions .......................................................................................... 2
Introduction
Product Features.................................................................................. 3
Package Overview ............................................................................... 4
Product Overview ................................................................................. 5
Installation
Connecting the Projector to Desktop Computer................................... 8
Connecting the Projector to Portable Computer ................................... 9
Connecting the Projector to Other Video Sources ............................... 10
Powering On/Off the Projection Display ............................................... 12
Adjusting the Projected image .............................................................. 14
User Controls
Panel Control & Remote Control .......................................................... 16
On-Screen Display Menus................................................................... 18
Appendices
Troubleshooting .................................................................................... 22
Changing the Lamp............................................................................... 25
Specifications ....................................................................................... 26
Compatibility Modes ............................................................................. 27
3
English
Introduction
Product Features
This product, is an SVGA single chip 0.7”DLPä Projector. The outstanding
features of it are listed as follows:
q True SVGA, 800 x 600 addressable pixels
q 5 lbs (2.3 kgs) lightweight compact design
q Single chip DLPä technology
q XGA compression and VGA re-sizing
q 150 Watts user replaceable P-VIP lamp
q Mac/NEC PC-98/FM Towns compatible
q NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM Video compatible
q Full function wireless remote controller
q Real plug & play with auto image function
q User friendly Multilingual on-screen display menu
q Advanced electronic keystone correction and picture in picture function
q Luxurious carrying case included
4
English
Package Overview
This projection display comes with all the items shown below. Check to make
sure your unit is complete. Contact your dealer immediately if anything is
missing.
Projection Display
Power Cord
VGA Cable
S-Video Cable
Audio-In Cable for Computer
Composite Video Cable
Audio Cable
User’s Manual
Warranty Card
Remote Control
Carrying Case
5
English
Product Overview
Main Unit
Panel Control
Focus Ring
Remote Control
Receiver
Focus Ring
Lens
Speaker
Firmware Upgrade Port
Carrying Handle
Connection Ports
Elevator Button
Elevator Foot
Power Connector
Power Switch
Security Lock Slot
vNotice : Firmware Upgrade is for after service purpose only.
6
English
Connection Ports
Computer Input
Connector
Audio Iuput
Connector
Audio Output
COMPUTER IN
Composite Video
Connector
S-video
Connector
Connector
IN
OUT
AUDIO
S-VIDEO VIDEO
Power Connector
Power Switch
Panel Control
Four Directional
Select Keys
Menu
Power /
Standby
Reset
Temperature
Lamp
Source
Enter
7
English
Remote Control
Source
Reset
Power / Standby
Resync
Mute
Freeze/CLR
Picture in Picture
Volume ( + / - )
Menu
Keystone Correction
Four Directional
Select Keys
Zoom In / Zoom Out
Enter
8
English
Installation
Connecting the Projector to Desktop Computer
1. Make sure the projector and your computer are turned off.
2. Connect one end of the projector signal cable to the projector; connect the other
end to the VGA connector on the computer and tighten the screws.
3. Connect one end of the power cord into the back of projector; connect the other
end to an electrical outlet.
Computer Output
VGA Cable
Power Cord
v To ensure the projection display works well with your computer, please configure
the display mode of your graphic card to make it less than or equal to 800 X 600
resolution. Make sure timimg of the display mode is compatible with the projection
display. Refer to the“Compatibility Modes”section on page 27.
9
English
Connecting the Projector to Portable Computer
1. Make sure the projector and your notebook are turned off.
2. Connect one end of the projector signal cable to the projector; connect the other
end to the VGA connector on the notebook and tighten the screws.
3. Connect one end of the power cord into the back of projector; connect the other
end to an electrical outlet.
Notebook Output
VGA Cable
COMPUTER IN
IN
OUT
AUDIO
VIDEO
S-VIDEO
Power Cord
10
English
Connecting the Projector to Other Video Sources
v If your video player uses a round, one-prong composite video connector, you’ll
need the video cable. If your video player uses a round, four-prong s-video
connector, you’ll need the s-video cable ( See page 11 for detail information).
Both cables are shipped with the projector.
If you use the video cable:
1. Plug the video cable connector into the “Video out”port on your video player; plug
the other end into the “Video”port on your projector.
2. Plug the audio cable white connector into the left “Audio out” port on your video
player; plug the cable’s red connector into the right “Audio out” port on the video
player; plug the other end into the “Audio in” port on your projector.
3. If you need to use an external speaker (built in amplifier), plug the audio cable white
connector into the “Audio in” port on your speaker; plug the cable’s red connector into
the red “Audio in” port on the speaker; plug the other end into the “Audio out”
port on the projector.
4. Connect one end of the power cord into the back of projector; connect the other
end to an electrical outlet.
VideoOutput
AudioOutput
Audio In Port
Video Port
AudioCable
Audio Out Port
AudioCable
VideoCable
Power Cord
11
English
If you use the s-video cable:
1. Plug the s-video cable connector into the “S-Video”port on your video player; plug
the other end into the “S-Video” port on your projector.
2. Plug the audio cable white connector into the left “Audio out” port on your video
player; plug the cable’s red connector into the right “Audio out” port on the video
player; plug the other end into the “Audio in” port on your projector.
3. If you need to use an external speaker (built in amplifier), plug the audio cable white
connector into the white “Audio in” port on your speaker; plug the cable’s red con-
nector into the red “Audio in” port on the speaker; plug the other end into the “Audio
out” port on your projector.
4. Connect one end of the power cord into the back of projector; connect the other
end to an electrical outlet.
AudioOutput
S-VideoOutput
Audio in port
S- Video port
AudioCable
S-Video Cable
AudioCable
COMPUTER IN
IN
OUT
AUDIO
VIDEO
S-VIDEO
Audio out port
Power Cord
12
English
Power On/Off the Projection Display
uPowering On the Projection Display
1. Remove the lens cap.Œ
2. Ensure that the power cord and signal cable are securely connected.
3. Turn on the main power switch on the back of the projector and allow the projector
to warm up for 1-2 minutes.
4. Turn on the lamp by pressing “Power/Standby” button on the Panel Control.Ž
The startup screen will display for 30 seconds and the Power/Standby indicator will
light solid green.
5. Turn on your source (computer, notebook, or video player ,etc.). The projector will
detect your source automatically.
* If the screen displays “No Signal” , please make sure the signal cables are
securely connected.
* If you connect multiple sources at the same time, use the “Source” button
on the Remote Control or Panel Control to switch.
Power/
Standby
Lens cap
Ž
Œ
Power Switch
13
English
uPowering Off the Projection Display
1. Press the “Power/Standby” button to turn off the projector lamp.
2. After pressing the “Power/Standby” button, you will see a message “ Power off the
lamp? ” on the on-screen display. Press the “Power/Standby” button again to confirm.
Otherwise the message will disappear after 5 seconds.
3. “LAMP “ LED indicator will flash amber for about one minute. After the “LAMP” LED
indicator stops flashing , you can turn off the main power switch on the back of the
projector.
*If you want to turn on the main power switch immediately, you must allow about 10
minutes for thermal dissipation.
4. Disconnect the power cord from the electrical outlet and the projector.
* When the “LAMP” indicator lights solid amber; please change the lamp
module immediately.
* When the “TEMP” indicator lights solid amber, it indicates the display
has been overheated. The display will automatically shut itself down.
Under normal conditions, the display can be switched on again for your
presentation. If the problem persists, you should contact your local dealer or
our service center.
14
English
Adjusting the Projected Image
u Adjusting the Projector Height
The projector is equipped with an elevator foot for adjusting the projector height.
To raise the projector:
1. Press and hold the elevator button Œ.
2. Raise the projector to the desired display angle , then release the button to lock the
elevator foot into position.
To lower the projector:
1. Press and hold the elevator button.
2. Lower down the projector, then release the button to lock the elevator foot into position.
Œ
Elevator Button
Elevator Foot
* When you adjust the projector height; please place the projector on a flat surface
and avoid falling down of the projector.
* For safety purpose, when you adjust the projector height; please loosen the
wheels Œunder the elevator foot and pull the stands out .
Œ
15
English
u Adjusting the Projector Focus
To focus the image, rotate the focus ring until the image is clear. The projector will focus at
distances from 3.3 feet to 32.8 feet (1m to 10m).
Zoom Ring
Focus Ring
u Image Size Adjustment
Screen
Distance
Screen
Size
*This graphis for user’s reference only.
16
English
User Controls
Panel Control & Remote Control
There are two ways for you to control the functions: Remote Control and
Panel Control.
Panel Control
Remote Control
Power / Standby
Power the lamp on and off when the main power switch is turned on.
4
Menu
Press “Menu” to open the on-screen display (OSD) menus and to switch among different
4
menus. To exit OSD, press the “Freeze/CLR” button or select the “ Exit Menu” icon and press
“Enter” button. The projector saves any changes you made automatically.
Source
Press “Source” to choose between video and computer sources.
4
Reset
When you press the “Reset” button, the OSD menus displays a message “Reset All Yes/NO ? ”.
4
Select “Yes” to confirm or select “ No” to cancel.This function will reset all user adjustable
parameters to factory default settings.
17
English
Enter
Press “Enter” to confirm your selection.
4
Four Directional Select Keys
Use
or
to select items. Use
or
to make adjustments for your selection.
4
Volume
To increase the volume, press
To decrease the volume, press
To mute the volume, press “Mute”
4
4
4
Resync
Automatically synchronizes the projector to the input source.
4
Freeze/CLR
Press the “Freeze/CLR” button to still the screen image.
4
When the OSD is displayed, press the “Freeze/CLR” button to exit the OSD.
4
PIP (Picture in Picture)
Display a video source image on a small screen. (Computer mode only).
4
Please refer to “Page 20” for more information.
Zoom In (Computer mode only)
Magnifies an image up to a factor of 32 times on the projection screen.
4
When the “Zoom” icon is displayed, you can use the four directional select keys to change the
vertical or horizontal positioning of the image.
4
Zoom Out (Computer mode only)
Diminishes the zoom in image.
4
When the “Zoom” icon is displayed, you can use the four directional select keys to change the
4
vertical or horizontal positioning of the image.
Keystone
Adjusts image distortion caused by tilting the projector.
4
18
English
On-Screen Display Menus
How to operate
The Projector has a multilingual On-Screen Display(OSD) menu that allows you
to make image adjustments and change a variety of settings. In computer
source, the OSD will be the “Computer OSD”. In video source, the OSD will
be the “ Video OSD”. The projector will detect the source automatically.
4
To open the OSD menu, press the “menu” button on the Remote Control or Panel
Control.
4
4
To select among different menus, press the” Menu” button again. Then use
to select different items and use
to adjust your selection.
To exit the OSD, choose the “Exit Menu” and press the enter button.
4
4
When the OSD is displayed, press the “Freeze/CLR” button to exit the OSD.
Language
Language
4
You can display the multilingual OSD menu . Use the “ Up” and “ Down” key to select the
language you prefer. The menus redrew immediately.
Display
Brightness
4
Adjusting the brightness of the image.
l Press the left key to darken the image.
l Press the right key to lighten the image.
Contrast
4
The contrast controls the degree of difference between the lightest and darkest parts of the
picture. Adjusting the contrast changes the amount of black and white in the image.
l Press the left key to decrease the contrast.
l Press the right key to increase the contrast
Keystone Correction
4
Adjusts image distortion caused by tilting the projector.
Color Temperature
4
Adjusts the color temperture. The range is from 6500K to 7700K . The factory default is 7100K .
With the higher temperature, the screen looks colder; with the lower temperature, the screen
looks warmer.
19
English
Tint (Video mode only)
4
The tint adjusts the red-green color balance in the projected image.
l
Press the left key to increase the amount of green in the image.
Press the right key to increase the amount of red in the image.
l
Color (Video mode only)
4
The color setting adjusts a video image from black and white to fully saturated color.
l Press the left key to decrease the amount of color in the image.
l Press the right key to increase the amount of color in the image.
Image (Computer mode only)
Tracking
4
Choose “ Tracking” item to synchronize the signal timing of the display with that of the graphic
card. When you experience an unstable or flickering image, use this function to correct it.
Frequency
4
“Frequency” is for changing the display data frequency to match the frequency of your
computer’s graphic card. When you experience a vertical flickering bar, use this function to make
an adjustment.
Horizontal Position
4
l
Press the left button to move the image left.
Press the right button to move the image right.
l
Vertical Position
4
l
Press the left button to move the image up.
Press the right button to move the image down.
l
Auto-Image
4
The projector automatically adjusts tracking, frequency and vertical and horizontal
position for most computers.
* The image options are available only for computer sources. The projector sets these options
automatically for video sources.
Audio
Volume
4
l
Press the left button to decrease the volume.
Press the right button to increase the volume.
l
Bass
4
The Bass setting controls the lower frequencies of your audio source.
l
l
Press the left button to decrease the bass.
Press the right button to increase the bass.
20
English
Treble
4
The treble setting controls the higher frequencies of your audio source.
l
Press the left button to decrease the treble.
Press the right button to increase the treble.
l
Mute
4
l
Choose the left icon to make the volume function ineffective.
Choose the right icon to make the volume function effective.
l
Mono / Stereo / Stereo-enhance
4
l
Mono: Mono sound effect.
l
l
Stereo: Stereo sound effect.
Stereo-enhance: Stereo-enhance sound effect.
Projection
Front-Desktop
4
The factory default setting.
Rear-Desktop
4
When you select this function, the projector reverses the image so you can project behind a
translucent screen.
Front-Ceiling
4
When you select this function, the projector turns the image upside down for ceiling-mounted
projection.
Rear-Ceiling
4
When you select this function, the projector reverses and turns the image upside down at same time.
You can project from behind a translucent screen with ceiling mounted projection.
16:9 (Video mode only)
4
You can select this function to fit your DVD aspect ratio type.
4:3 (Video mode only)
4
You can select this function to fit your DVD aspect ratio type.
PIP (Computer mode only)
4
Choose “On” to turn on the PIP screen. When the PIP screen displayed, use the four directional
select keys to change the PIP screen position. Choose “Off” to trun off the PIP screen.
21
English
Lamp
LampWarning
4
Choose this function to show or hide the warning message when the lamp changing warning
message is displayed.
Lamp Reset
4
Reset the lamp setting only when the lamp changing is done.
Exit Menu
Exit Menu
4
When you want to close the OSD menu, choose this item and select “ Yes” to exit menu.
Reset All
4
Choose “ Yes” to return the display parameters of the current mode to its factory default settings.
22
English
Appendices
Troubleshooting
If you are experiencing trouble with the projection display, refer to the following. If the
problem persists, please contact your local dealer or our service center.
Problem: No image appears on screen.
Ensure all the cables and power connections are correctly and securely connected
as described in the “Installation” section.
4
If the projector is plugged into a power strip, make sure the power strip is turned on.
Ensure the pins of connectors are not crooked or broken.
4
4
4
Check if the projection lamp has been securely installed. Please refer to the “Changing
the lamp” section.
Make sure you have removed the lens cap and the projector is switched on.
4
Problem: Partial, scrolling or incorrectly displayed image.
4Press the “Resync”button on the Remote Control.
If you are using a PC:
4
If the resolution of your computer is higher than 800 x 600. Follow the steps
outlined below to reset the resolution.
For Windows 3.x:
1. In the Windows Program Manager, click the “Windows Setup” icon in the Main
group.
2. Verify that your display resolution setting is less than or equal to 800 x 600.
For Windows 95:
1. Open “My Computer” icon, the “Control Panel” folder, and then double click the
“Display” icon.
2. Select the “Setting” tab.
3. In the “Desktop Area” you will find the resolution setting. Verify that the
resolution setting is less than or equal to 800 x 600 resolution.
If the projection display is still not projecting the whole image, you will need
to also change the monitor display you are using. Refer to the following steps.
23
English
4. Follow above steps 1~2. Click on the “Advanced Properties ” button.
5. Select the “Change” button under the “Monitor” tab .
6. Click on “ Show all devices ”. Then select “ Standard monitor types ” under the
“ Manufactures ” box; choose the resolution mode you need under the “ Models”
box.
7. Verify that the resolution setting of the monitor display is less than or equal to
800 x 600.
If you are using a Notebook PC:
4
1. You are required to implement above steps of resolution setting of computer first.
2. Switch the Notebook PC display to the “external display only” or “CRT only”
mode.
If you are experiencing difficulty in changing resolutions or your monitor freezes,
restart all the equipment and the projection display.
4
Problem: The screen of the Notebook or PowerBook computer is not displaying
your presentation.
If you are using Notebook PC:
4
Some Notebook PCs may deactivate their own computers’ screens when a
second display device is in use. Each of them has different way to be reactivated.
Refer to your computer’s documentation for detailed information.
If you are using an Apple PowerBook:
4
In Control Panels, open the PowerBook Display to select Video Mirroring “On”.
Problem: Image is unstable or flickering
Use “Tracking” to correct it.
4
4
Change the monitor color setting from your computer.
Problem: Image has vertical flickering bar
Use “Frequency” to make an adjustment.
4
4
Check and reconfigure the display mode of your graphic card to make it compatible
with the product.
Problem: Image is out of focus
Adjust the Focus Ring on the projector lens.
4
4
Make sure the projection screen is between the required distance 3.3ft.(1m)~ 32.8ft.
(10m) from the projector.
24
English
Problem: The screen is outstretched when displaying 16:9 DVD
The projector itself will automatically detect 16:9 DVD and adjust the aspect ratio by digitiza-
tion to full screen with 4:3 default setting.
If the projection display is still outstretched, you will also need to adjust the aspect ratio by
referring to the following:
Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD.
4
4
If you can not select 4:3 aspect ratio type on your DVD player, please select 4:3 On-
Screen-Display (OSD) function of the projector for your display.
English
25
English
Changing the lamp
The projection display will detect the lamp life itself. It will show you a warning
message “ Lamp is running out of standard lifetime. Be sure to replace the lamp as
soon as possible.”. When you see this message, change the lamp as soon as
possible.
Make sure the projection display has been cooled for at least 30 minutes before
changingthelamp.
Warning: Lamp compartment is hot! Allow it to cool before changing lamps!
Lamp Changing Procedure:
4
1. Turn off the power to the projector by pressing the Power/Standby button.
2. Allow the projector to cool down at least 30 minutes.
3. Turn off the main power switch.
4. Disconnect the power cord.
5. Use screwdriver to remove the screw from the cover.
Œ
6. Remove the cover.
7. On the left side of the lamp module, push the electrical connector up to disengage it
from the projector base.
Ž
8. Remove the three screws from the lamp module.
9. Pull out the lamp module.
To replace the lamp module, reverse the previous steps.
Warning: To reduce the risk of personal injury, do not drop the lamp module
or touch the lamp bulb. The bulb may shatter and cause injury if it is
dropped.
Œ
Ž
26
English
Specifications
Light Valve
- Single Chip DLPTM Technology
- 400:1 (Full On / Full Off)
- 150:1 (ANSI Contrast)
- 150W User Replaceable P-VIP Lamp
- 800 pixels(H) X 600 lines(V)
- 16.7M colors
Contrast Ratio
Lamp
Number of Pixels
Displayable Color
Projection Lens
- F2.8 f=30.7mm
Projection Screen Size
Projection Distance
Computer Compatibility
- 17”~ 215” Diagonal
- 3.3~32.8 ft (1m~10m)
- IBM & VESA VGA
640 x 350, 70/85 Hz
720 x 400, 70/85 Hz
VGA
640 x 480, 60/70/72/75/85 Hz
800 x 600, 56/60/72/75/85 Hz
1024 x 768, 43/60/70/75/85 Hz Compressed
640 x 480, 66.66 Hz
SVGA
VESA XGA
- APPLE Macintosh LC 13”
APPLE Macintosh II 13”
APPLE Macintosh 16”
APPLE Macintosh 19”
- NECPC-98SERIES
640 x 480, 66.68 Hz
832 x 624, 74.55 Hz
1024 x 768, 75 Hz Compressed
640 x 400, 56.42 Hz
640 x 480, 70/60 Hz
- FUJITSUFM-TOWN
640 x 480, 55.37/60 Hz
Video Compatibility
- NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM compatible
- Composite video & S-Video capability
- 25kHz~69kHz horizontal scan
H. Frequency
V. Frequency
Multimedia Audio
- 43Hz~85Hz vertical refresh
- One internal speaker with 3 watt output
- Audio Line Output
Power Supply
- AC input 110~240V Auto-Switching Power Supply
- 210 watts at normal operation
Power Consumption
I/O Connectors
- Power: AC Power Input Socket
- Computer Input: One 15-pin D-sub Computer Input
- Video Input: One Composite Video RCA Input
One S-Video Input
- Audio Input: One Phone Jack for Audio Input
- Audio Output: One Phone Jack for Audio Line out
- 5 lbs. / 2.3 kgs
Weight
Dimensions (W x H x D)
Environmental
- 3.54 x 8.58 x 9.9 inches / 90 x 218 x 252 mm
- Operating Temperature:
Humidity:
10o~ 40oC/50o~104oF
80% maximum
- Storage Temperature:
Humidity:
-20o~60oC/ -4o~140oF
80% maximum
Safety Regulation
- FCC, CE , VCCI, UL, CUL, TUV, BCIQ
27
English
Compatibility Modes
V.Frequency H.Frequency
Mode
Resolution
(Hz)
(kHz)
* Compressed
|