INSTALLATION INSTRUCTIONS FOR PART 99-7502
APPLICATIONS
Mazda MPV 2000-2006
99-7502
KIT FEATURES
• DIN Mount Radio Provision
• ISO Mount Radio Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Snap In Brackets • C) Trim Plate
C
B
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
99-7502 DASH DISASSEMBLY
MAZDA MPV 2000-2006
A
1
2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Remove (2) Phillips head screws from
above instrument cluster. (Figure A)
3
4
Unclip and remove the radio trim
panel. (Figure B)
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
(Figure C)
B
Continue to kit assembly.
C
1
99-7502 KIT ASSEMBLY
DIN MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
2
Slide the aftermarket radio into the
cage until it snaps into place. (Figure B)
Continue to final assembly.
B
2
99-7502 KIT ASSEMBLY
ISO DIN MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
2
3
Slide the radio into the radio housing
until it snaps into place. (Figure B)
Snap the Trim plate onto the front of
the Radio Housing assembly.
(Figure B)
Continue to final assembly.
B
3
99-7502 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
99-7502
NOTES
5
99-7502 INSTRUCTIONS
1-800-221-0932
REV. 10/12/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
INST99-7502
|