USER GUIDE
Wireless ADSL2+ Modem Router
Models: WAG120N, WAG160N v2, WAG320N
Table of Contents
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Placement Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How to Access the Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Screens in the Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setup Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wireless Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Storage Tab (WAG320N Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Security Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Access Restrictions Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Applications & Gaming Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Administration Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WAG160N v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
United States of America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Wireless ADSL2+ Modem Router
ii
Product Overview
Chapter 1
USB (WAG320N only) (Green) The USB LED
lights up when a USB device is connected to the
Modem Router through the USB port.
Chapter 1:
Product Overview
Thank you for choosing the Wireless ADSL2+ Modem
Router. This device lets you access the Internet via a
wireless connection or through one of its four switched
ports. You can also use it to share resources such as
computers, printers and files. A variety of security features,
such as WPA2™ security, a Stateful Packet Inspection (SPI)
firewall and NAT technology, help to protect your data
and your privacy while online. Configuration is easy using
the provided browser-based utility.
Wireless (Green) The Wireless LED lights up
when the wireless feature is enabled. It flashes
when the Modem Router is actively sending or
receiving data over the network.
DSL (Green) The DSL LED lights up whenever
there is a successful DSL connection. The LED
flashes green while the Modem Router is
establishing the ADSL connection.
Internet (Green/Red) The Internet LED lights up
green and stays on when a connection is made
through the Internet port. It flashes to indicate
network activity over the Internet port. The LED
is lit red when an authentication error occurs.
Front Panel
Back Panel
Power (WAG120N: Green/Amber; WAG160N v2
and WAG320N: Green/Red) The Power LED
is continuously lit green while the device is
powered on. The LED is lit amber (WAG120N)
or red (WAG160N v2 and WAG320N) if a POST
(Power On Self Test) failure or device malfunction
occurs.
DSL The DSL port connects to the ADSL line.
Ethernet 4, 3, 2, 1 The Ethernet ports (4, 3, 2, 1)
connect the Modem Router to wired computers
and other Ethernet network devices.
Ethernet 1-4 (Green) These numbered LEDs,
one for each of the numbered ports on the
Modem Router’s back panel, serve two purposes.
If the LED is continuously lit, the Modem Router is
successfully connected to a device through that
port. It flashes to indicate network activity over
that port.
NOTE: The Ethernet
1
port can
also be configured as the WAN
port. To do this, access the Web-
based utility (refer to “Chapter 3:
then select the Setup > Ethernet tab.
NOTE: The Ethernet 1 LED is lit amber
when the WAN link is established on that
port.
USB (WAG320N only) The USB port connects
the Modem Router to a hard drive or flash-
based USB storage device.
Wi-Fi Protected Setup™ Button (WAG120N:
Green/Amber; WAG160N v2 and WAG320N:
Green) Press this button to have Wi-Fi Protected
Setup™ search for your Wi-Fi Protected
Setup™-supported wireless device. The LED is
continuously lit green when a Wi-Fi Protected
Setup™ connection is successfully established.
The LED blinks slowly while Wi-Fi Protected
Setup™ is setting up a connection, and is lit amber
(WAG120N) or blinks rapidly (WAG160N v2 and
WAG320N) if an error occurs. The LED is off when
Wi-Fi Protected Setup™ is idle.
Reset There are two ways to reset the Modem
Router’s factory defaults. Either press and
hold the Reset button for approximately five
seconds, or restore the defaults from the
Administration > Factory Defaults screen of the
Modem Router’s web-based utility.
Power The Power port is where you will connect
the power adapter.
On/Off Button Press the On/Off button to turn
power to the device on or off.
NOTE: Wi-Fi Protected Setup™ is a feature
that makes it easy to configure your
wireless network and its security settings.
Wireless ADSL2+ Modem Router
1
Product Overview
Chapter 1
Follow these instructions:
Placement Positions
There are two ways to physically install the device. The
first way is to place the device horizontally on a surface.
The second way is to mount the device on a wall.
1. Determine where you want to mount the device. Make
sure that the wall you use is smooth, flat, dry, and
sturdy. Also make sure the location is within reach of
an electrical outlet.
The best place for the device is usually at the center of
your wireless network, within range of all of your wireless
devices.
2. Drill two holes into the wall. Make sure the holes are
152 mm (6 inches) apart.
3. Insert a screw into each hole and leave 3 mm
(0,12 inches) of its head exposed.
Horizontal Placement
The device has four rubber feet on its bottom panel. Place
the device on a level surface near an electrical outlet.
4. Maneuver the device so the wall-mount slots line up
with the two screws.
5. Place the wall-mount slots over the screws and slide
the device down until the screws fit snugly into the
wall-mount slots.
Wall-Mounting Placement
The device has two wall-mount slots on its bottom
panel. The distance between the slots is 152 mm
(6 inches).
Two screws are needed to mount the device.
Suggested Mounting Hardware
4-5 mm
1-1,5 mm
†Note: Mounting hardware illustrations are not
true to scale.
NOTE: Cisco is not responsible for damages
incurred by insecure wall-mounting hardware.
152 mm
Wall Mounting Template
Wireless ADSL2+ Modem Router
2
Wireless Security Checklist
Chapter 2
Chapter 2:
4. Enable encryption
Wireless Security Checklist
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access™ (WPA™/WPA2™) and
Wired Equivalency Privacy (WEP) offer different levels of
security for wireless communication.
Wireless networks are convenient and easy to install, so
homes with high-speed Internet access are adopting them
at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
A
network encrypted with WPA™/WPA2™ is more
secure than a network encrypted with WEP, because
WPA™/WPA2™ uses dynamic key encryption. To protect
the information as it passes over the airwaves, you should
enable the highest level of encryption supported by your
network equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA™.
1. Change the default wireless
network name or SSID
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This is
the name of your wireless network, and can be up to 32
characters in length. Linksys by Cisco wireless products
use linksys as the default wireless network name. You
should change the wireless network name to something
unique to distinguish your wireless network from other
wireless networks that may exist around you, but do not
use personal information (such as your Social Security
number) because this information may be available for
anyone to see when browsing for wireless networks.
•
Password protect all computers on the network and
individually password protect sensitive files.
•
•
Change passwords on a regular basis.
Install anti-virus software and personal firewall
software.
•
Disable file sharing (peer-to-peer). Some applications
may open file sharing without your consent and/or
knowledge.
2. Change the default password
Additional Security Tips
For wireless products such as access points, routers, and
modem routers, you will be asked for a password when
you want to change their settings. These devices have a
default password set by the factory. The default password
is admin. Hackers know these defaults and may try to
use them to access your wireless device and change your
network settings. To thwart any unauthorized changes,
customize the device’s password so it will be hard to
guess.
•
Keep wireless routers, access points, or modem routers
away from exterior walls and windows.
•
Turn wireless routers, access points, or modem routers
off when they are not being used (at night, during
vacations).
•
Usestrongpassphrasesthatareatleasteightcharacters
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
3. Enable MAC address filtering
WEB:Formoreinformationonwirelesssecurity,
Linksys by Cisco routers and modem routers give you
the ability to enable Media Access Control (MAC) address
filtering. The MAC address is a unique series of numbers
and letters assigned to every networking device. With
MAC address filtering enabled, wireless network access
is provided solely for wireless devices with specific MAC
addresses. For example, you can specify the MAC address
of each computer in your home so that only those
computers can access your wireless network.
Wireless ADSL2+ Modem Router
3
Advanced Configuration
Chapter 3
List of Screens in the Utility
The screens are organized hierarchically as listed below.
(Some screens may not apply to all models.)
Chapter 3:
Advanced Configuration
After you finish running the Setup Wizard on the Setup
CD-ROM, the device is ready for use.To change the device’s
advanced settings, access the Configuration Utility via a
web browser on a computer connected to the device.
NOTE FOR USERS IN NEW ZEALAND: Refer to
the Note in Setup > Basic Setup, page 5 for
setup instructions specific to your country.
How to Access the Utility
Launch the web browser on your computer, and enter the
device’s default IP address, 192.168.1.1, in the Address
field. Then, press Enter.
A login screen appears. Use the default user name and
password, admin, unless you changed them when you
ran the Setup Wizard. (You can set a new user name and
password from the Administration tab’s Management
screen.) Click OK to continue.
Login
If you are unable to log in, press the Reset button on the
back panel for at least 5 seconds, then wait for the device
to reset and try again.
Using the Utility
Immediately after login, the Basic Setup screen appears.
Near the top of the screen is a bar with selectable tabs.
Use these tabs to navigate within the Utility. The primary
tabs indicate the Utility’s main configuration categories.
Each primary tab has one or more secondary tabs that
provide access to the primary tab’s configuration screens.
Primary Tabs
Access
Restrictions
Applications &
Gaming
Setup Wireless Storage Security
Administration Status
Basic Setup Ethernet DDNS MAC Address Clone Advanced Routing
Secondary Tabs
Navigation Tabs
To access a screen, click the appropriate primary tab,
then click the appropriate secondary tab. The screen will
appear, with its primary and secondary tabs highlighted.
Wireless ADSL2+ Modem Router
4
Advanced Configuration
Chapter 3
Setup > Advanced Routing
Setup Tab
The Advanced Routing screen allows you to configure the
device’s advanced routing functions, such as operating
mode, dynamic mode, and static routing.
The Setup tab provides the device’s basic setup functions.
For detailed information on the Setup tab, refer to the
Utility’s online help pages.
Wireless Tab
Setup > Basic Setup
The Wireless tab allows you to configure the device’s
wireless functions.
The Basic Setup screen allows you to change the device’s
general settings. The following connection types
(encapsulations) are available:
For detailed information on the Wireless tab, refer to the
Utility’s online help pages.
•
•
•
•
•
•
•
RFC 2364 PPPoA
RFC 2516 PPPoE
RFC 2684 Routed
IPoA
RFC 2684 Bridged - Dynamic IP Address
RFC 2684 Bridged - Static IP Address
Bridge Mode Only
Wireless > Basic Wireless Settings
The Basic Wireless Settings screen allows you to set up a
network with Wi-Fi Protected Setup™, change the radio
band, select the network mode, change the wireless
network name (SSID), change the wireless channel and
disable the SSID broadcast.
NOTE FOR USERS IN NEW ZEALAND: To set up
the device, follow these instructions:
Wireless > Wireless Security
The Wireless Security screen allows you to configure the
security of your wireless network(s). It allows you to select
from a number of security modes, such as WPA2.
1. Access the Setup > Basic Setup screen.
2. Select RFC 2364 PPPoA from the
Encapsulation drop-down menu.
Wireless > Wireless MAC Filter
The Wireless MAC Filter screen allows you to control (block
or allow) Internet access by individual devices on your
wireless network by specifying their MAC addresses.
3. For the Virtual Circuit ID, enter 0 for the VPI
and 100 for the VCI.
4. Select VC for Multiplexing.
5. Select Multimode from the DSL Modulation
drop-down menu.
Wireless > Advanced Wireless Settings
The Advanced Wireless Settings screen allows you to
6. Enter your User Name and Password details
from your ISP.
7. Click Save Settings.
configure the device’s advanced wireless functions.
Storage Tab (WAG320N Only)
The Storage tab allows you to configure the settings for an
optional external USB storage device, such as a flash drive
or hard disk drive.
Setup > Ethernet
The Ethernet screen allows you to configure the device’s
Ethernet settings. It also allows you to set up the first
Ethernet port as a WAN port.
For detailed information on the Storage tab, refer to the
Utility’s online help pages.
Setup > DDNS
The DDNS screen allows you to assign a fixed host and
domain name to a network computer that has been
assigned a dynamic Internet IP address. This is useful
when you are hosting your own website, FTP server, or
other server behind the device.
Storage > Disk Management
The Disk Management screen displays information on an
attached USB storage device, and allows you to perform
basic management functions on the device. It also
provides information on the attached USB disk, allows for
a blank disk to be formatted, and enables safe removal of
the attached disk.
Setup > MAC Address Clone
Some service providers require you to register a MAC
address in order to access the Internet. The MAC Address
Clone screen lets you use the MAC address of a device that
has already been registered with your service provider, by
copying that MAC address to the device.
Storage > Shared Folder
The Shared Folder screen allows you to manage the shared
folders on an external USB storage device. A shared folder
Wireless ADSL2+ Modem Router
5
Advanced Configuration
Chapter 3
is a directory on the device that a user can access through
the network.
For detailed information on the Applications & Gaming
tab, refer to the Utility’s online help pages.
Storage > Administration
Applications & Gaming > Single Port Forwarding
The Administration screen allows you to configure basic
storage settings and manage the device’s users.
The Single Port Forwarding screen allows you to set up
port forwarding for a single port. You should assign static
IP addresses to the destination computers before you use
this feature.
Storage > Media Server
The Media Server screen allows you to configure the
device’s built-in media server, and to select the folders to
scan for content.
Applications & Gaming > Port Range Forwarding
The Port Range Forwarding screen allows you to set up
port forwarding for a range of ports. You should assign
static IP addresses to the destination computers before
you use this feature.
Security Tab
The Security tab allows you to enhance the security of
your network.
Applications & Gaming > Port Range Triggering
For detailed information on the Security tab, refer to the
Utility’s online help pages.
The Port Range Triggering screen allows you to set up port
triggering. When port triggering is configured, the device
watches for specified port numbers in outgoing data.
When a match is found, the device records the sending
computer’s IP address so that when the requested data
returns, it can be sent to the proper computer.
Security > Firewall
The Firewall screen allows you to configure a firewall that
can filter out various types of unwanted traffic on the
device’s local network.
Applications & Gaming > DMZ
Security > VPN Passthrough
The DMZ screen allows you to expose one network user
to the Internet for use of a special-purpose service such
as Internet gaming or video conferencing. DMZ hosting
forwards all the ports at the same time to one computer.
You should assign static IP addresses to the destination
computers before you use this feature.
The VPN Passthrough screen allows you to configure the
device’s VPN passthrough feature. This feature lets VPN
tunnels using the IPSec, L2TP, or PPTP protocols to pass
through the device’s firewall.
Access Restrictions Tab
The Access Restrictions tab allows you to configure
the Internet access restrictions for each device in your
network.
Applications & Gaming > QoS
The QoS screen allows you to specify priorities for different
types of traffic. Lower priority traffic will be slowed down
to allow greater throughput or less delay for high priority
traffic.
For detailed information on the Access Restrictions tab,
refer to the Utility’s online help pages.
Administration Tab
The Administration tab allows you to configure the device’s
administrative functions.
Access Restrictions > Internet Access Policy
The Internet Access Policy screen allows you to define
policies that are used to block or allow specific kinds
of Internet usage and traffic, such as Internet access,
designated applications, websites, and inbound traffic
during specific days and times, and for a specified list of
devices in your network.
For detailed information on the Administration tab, refer
to the Utility’s online help pages.
Administration > Management
The Management screen allows you to manage specific
functions for access and security.
Applications & Gaming Tab
The Applications & Gaming tab allows you to configure
functions such as port forwarding and quality of service
that may be necessary for special applications such as
hosting web servers, ftp servers, and e-mail servers on on
your network, or other specialized internet applications
such as videoconferencing or online gaming.
Wireless ADSL2+ Modem Router
6
Advanced Configuration
Chapter 3
NOTE ON CISCO WEB ASSISTANT OPTION
Status Tab
The Status tab allows you to display status information.
(not on all models): If you see an “error code
404” message (indicating that you entered an
invalid web address), the Cisco Web Assistant
will appear and automatically run a search
based on the keywords in the web address. This
feature can be enabled or disabled from this
screen.
For detailed information on the Status tab, refer to the
Utility’s online help pages.
Status > Modem Router
The Modem Router screen displays information about the
device and its current settings. The on-screen information
will vary depending on the Internet Connection Type you
use.
NOTE ON TREND MICRO OPTION (not on all
models): Trend Micro ProtectLink Gateway
is a hosted security service that stops spam
and filters URLS to prevent unwanted content
from passing through your router. The Email
Protection is the hosted messaging security
solution provided by Trend Micro InterScan
Messaging Hosted Security (IMHS). This feature
can be enabled or disabled from this screen.
Status > Local Network
The Local Network screen displays the status of your Local
Area Network.
Status > Wireless Network
The Wireless Network screen displays some basic
information about the wireless network of the device.
Administration > Reporting
The Reporting screen allows you to configure system event
logging and to configure sending of e-mail alerts when a
Denial of Service attack is detected.
Status > DSL Connection
The DSL Connection screen displays the status of your DSL
connection.
Administration > Diagnostics
The Diagnostics screen allows you to perform a ping test
to check the status of your Internet connection.
Administration > Back Up & Restore
The Back Up & Restore screen allows you to back up and
restore the configuration settings of your device.
Administration > Factory Defaults
The Factory Defaults screen allows you to restore the
factory defaults of the device. All savings you have saved
will be lost
NOTE: Restoring the factory defaults causes all
settings you have previously saved to be lost.
Administration > Firmware Upgrade
The Firmware Upgrade screen allows you to upgrade the
device’s firmware.
Administration > Language
The Language screen allows you to select an available
language for the utility.
Wireless ADSL2+ Modem Router
7
Troubleshooting
Appendix A
You need to modify the basic settings on the
deviceRouter.
Appendix A:
Troubleshooting
Run the Setup Wizard on the Setup CD-ROM.
You need to modify the advanced settings on the
device.
Your computer cannot connect to the Internet.
Follow the instructions until your computer can connect
to the Internet:
Open the web browser (for example, Internet Explorer or
Firefox), and enter the device’s IP address in the address
field (the default IP address is 192.168.1.1). When
prompted, complete the User name and Password fields
(the default user name and password is admin). Click the
appropriate tab to change the settings
•
Make sure that the Modem Router is powered on. The
Power LED should be green and not flashing.
•
If the Power LED is flashing, then power off all of
your network devices, including the Modem Router
and computers. Then power on each device in the
following order:
WEB: If your questions are not
addressed here, refer to the website,
1. Modem Router
2. Computer
•
Check the LEDs on the device’s front panel. Make sure
the Power, DSL, and at least one of the numbered
Ethernet LEDs are lit. If they are not, then check
the cable connections. The computer should be
connected to one of the Ethernet ports numbered
1-4 on the device, and the device’s DSL port must be
connected to the ADSL line.
When you double-click the web browser, you are
prompted for a user name and password. If you want to
get rid of the prompt, follow these instructions.
Launch the web browser and perform the following steps
(these steps are specific to Internet Explorer but are similar
for other browsers):
1. Select Tools > Internet Options.
2. Click the Connections tab.
3. Select Never dial a connection.
4. Click OK.
You are using a static IP address and cannot connect.
Refer to Windows Help and change your Internet Protocol
(TCP/IP) Properties to Obtain an IP address automatically.
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the same
on both the computer and the device. If you have enabled
wireless security, then make sure the same security
method and key are used by both the computer and the
device.
Wireless ADSL2+ Modem Router
8
Specifications
Appendix B
Operating Temp. 0 to 40°C (32 to 104°F)
Appendix B:
Storage Temp.
-20 to 70°C (-4 to 158°F)
Operating
Humidity
Specifications
10 to 85% Noncondensing
Storage Humidity 5 to 90% Noncondensing
WAG120N
Standards
WAG160N v2
WLAN: 802.11n draft 2.0, 802.11g,
802.11b
Standards
WLAN: 802.11n draft 2.0, 802.11g,
802.11b
Ethernet: 802.3, 802.3u
ADSL: T1.413i2, G.992.1 (G.DMT),
G.992.2 (G.Lite), G.992.3 (ADSL2),
G.992.5 (ADSL2+) for Annex A, B, M, L,
U-R2 for Annex B
Ethernet: 802.3, 802.3u
ADSL: T1.413i2, G.992.1 (G.DMT),
G.992.2 (G.Lite), G.992.3 (ADSL2),
G.992.5 (ADSL2+) for Annex A, B, M, L,
U-R2 for Annex B
Ports
DSL, Ethernet (1-4), Power
Buttons
LEDs
On/Off, Reset, Wi-Fi Protected Setup™
Ports
Power, DSL, Ethernet (1-4)
Power, Ethernet (1-4), Security,
Wireless, DSL, Internet
Buttons
LEDs
On/Off, Reset, Wi-Fi Protected Setup™
Power, Ethernet (1-4), Ethernet WAN,
Security, Wireless, DSL, Internet
Cabling Type
CAT5, RJ-11 (for Annex A),
RJ-45 (for Annex B)
Cabling Type
CAT5, RJ-11 (for Annex A),
RJ-45 (for Annex B)
Antennas
2 Internal
Modulations
802.11b: CCK/QPSK, BPSK
Antennas
2 Internal
802.11g: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
Modulations
802.11b: CCK/QPSK, BPSK
802.11g: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
802.11n: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
802.11n: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
Transmit Power
802.11b: 17,0 1,0 dBm
802.11g: 15,0 1,0 dBm
802.11n: 13,0 1,5 dBm
Transmit Power
802.11b: 17,0 1,0 dBm
802.11g: 15,0 1,0 dBm
802.11n: 13,0 1,5 dBm
Receive Sensitivity -80 dBm (typical) @ 11 Mbps
-70 dBm (typical) @ 54 Mbps
Receive Sensitivity -80 dBm (typical) @ 11 Mbps
-72 dBm (typical) @ 54 Mbps
-61 dBm (typical) @ 130 Mbps
-61 dBm (typical) @ 270 Mbps
-66 dBm (typical) @ 130 Mbps
-63 dBm (typical) @ 270 Mbps
Antenna Gain
1,8 dBi
Security Features WPA2™/WPA™ Personal and Enterprise;
Antenna Gain
2 dBi
128, 64 bits WEP;
MAC Address Filtering;
SPI Firewall
Security Features WPA2™/WPA™ Personal and Enterprise
;
128, 64 bits WEP;
MAC Address Filtering;
SPI Firewall
OS Requirements Windows XP, Vista, or Vista 64-bit
(to run the
Setup CD)
edition with latest updates (for
Network Magic and Setup Wizard);
Mac OS X 10.4 or higher (for Setup
Wizard)
OS Requirements Windows XP, Vista, or Vista 64-bit
(to run the
Setup CD)
edition with latest updates (for
Network Magic and Setup Wizard);
Mac OS X 10.4 or higher (for Setup
Wizard)
Environmental
Dimensions
Weight
202 x 34 x 160 mm (8,0” x 1,3” x 6,3”)
362 g (12,8 oz)
Environmental
Dimensions
Weight
202 x 34 x 160 mm (8,0" x 1,3" x 6,3")
362 g (12,8 oz)
Power
12VDC, 1A
Certification
FCC, CE, Telepermit, K.21, UL, CB,
Wi-Fi (802.11b/g), WPA™, WPA2™,
WMM, Wi-Fi Protected Setup™
Power
12VDC, 1A
Certification
FCC, CE, Wi-Fi®, A-Tick,Telepermit,
WPA™, WPA2™
Wireless ADSL2+ Modem Router
9
Specifications
Appendix B
Operating Temp. 0 to 40°C (32 to 104°F)
5 GHz:
RIFA 1 & RIFA 2 & RIFA 3 ≤ 3,5 dBi
(Typical)
Storage Temp.
-20 to 70°C (-4 to 158°F)
Operating
Humidity
Security Features WPA2™/WPA™ Personal and Enterprise
;
10 to 85% Noncondensing
128, 64 bits WEP;
MAC Address Filtering;
SPI Firewall
Storage Humidity 5 to 90% Noncondensing
WAG320N
Standards
OS Requirements Windows XP, Vista, or Vista 64-bit
WLAN: 802.11n draft 2.0, 802.11g,
802.11b, 802.11a
(to run the
Setup CD)
edition with latest updates (for
Network Magic and Setup Wizard);
Mac OS X 10.4 or higher (for Setup
Wizard)
Ethernet: 802.3, 802.3u, 802.3ab
ADSL: T1.413i2, G.992.1 (G.DMT),
G.992.2 (G.Lite), G.992.3 (ADSL2),
G.992.5 (ADSL2+) for Annex A, M, L,
Environmental
Dimensions
202 x 34 x 160 mm
(8,0" x 1,3" x 6,3")
Ports
Power, DSL, Ethernet (1-4), USB
Weight
362 g (12,8 oz)
12VDC, 1,25A
Buttons
LEDs
On/Off, Reset, Wi-Fi Protected Setup™
Power
Power, Ethernet (1-4), Ethernet WAN,
Security, USB, Wireless, DSL, Internet
Certification
FCC, CE, Wi-Fi®, A-Tick,Telepermit,
WPA™, WPA2™
Cabling Type
Antennas
CAT5, RJ-11 (for Annex A)
3 Internal
Operating Temp. 0 to 40°C (32 to 104°F)
Storage Temp.
-20 to 70°C (-4 to 158°F)
Modulations
802.11a: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
Operating
Humidity
10 to 85% Noncondensing
802.11b: CCK/QPSK, BPSK
Storage Humidity 5 to 90% Noncondensing
802.11g: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
802.11n: OFDM/BPSK, QPSK, 16-QAM,
64-QAM
Transmit Power
2,4 GHz:
802.11b: 17,5 1,5 dBm Typical @
Normal Temp. Range
802.11g: 17,5 1,5 dBm Typical @
Normal Temp. Range
Wireless-N 20 MHz: 13,5 1,5 dBm
Typical @ Normal Temp. Range
Wireless-N 40 MHz: 13,5 1,5 dBm
Typical @ Normal Temp. Range
5 GHz:
802.11a: 13,5 1,5 dBm Typical @
Normal Temp. Range
Wireless-N 20 MHz: 13,5 1,5 dBm
Typical @ Normal Temp. Range
Wireless-N 40 MHz: 13,5 1,5 dBm
Typical @ Normal Temp. Range
Receive Sensitivity -80 dBm (typical) @ 11 Mbps
-72 dBm (typical) @ 54 Mbps
-66 dBm (typical) @ 130 Mbps
-63 dBm (typical) @ 270 Mbps
Antenna Gain
2,4 GHz:
RIFA 1 & RIFA 2 & RIFA 3 ≤ 4 dBi
(Typical)
Wireless ADSL2+ Modem Router
10
Regulatory Information
Appendix C
Appendix C:
Regulatory Information
Þetta tæki er samkvæmt grunnkröfum og
öðrum viðeigandi ákvæðum Tilskipunar
1999/5/EC.
Íslenska
[Icelandic]:
Questo apparato
é
conforme ai requisiti
Italiano
[Italian]:
essenziali ed agli altri principi sanciti dalla
Direttiva 1999/5/CE.
European Union
The following information applies if you use the product
within the European Union.
Šī iekārta atbilst Direktīvas 1999/5/
EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Latviski
[Latvian]:
Declaration of Conformity with Regard to EU
Directive 1999/5/EC (R&TTE Directive)
Compliance Information for 2,4-GHz and 5-GHz Wireless
Products Relevant to the EU and Other Countries
Following the EU Directive 1999/5/EC (R&TTE Directive)
Šis įrenginys tenkina 1999/5/EB Direktyvos
esminius reikalavimus ir kitas šios direktyvos
nuostatas.
Lietuvių
[Lithuanian]:
Dit apparaat voldoet aan de essentiele eisen
en andere van toepassing zijnde bepalingen
van de Richtlijn 1999/5/EC.
Nederlands
[Dutch]:
NOTE: The 5 GHz information does not apply to
Wireless-G (802.11g) only products.
Dan l-apparat huwa konformi mal-ħtiġiet
essenzjali u l-provedimenti l-oħra rilevanti
tad-Direttiva 1999/5/EC.
Malti
[Maltese]:
Това оборудване отговаря на съществените
Б ъ л г а р с к и
изисквания
и
приложими клаузи на
[Bulgarian]
Ez
a
készülék teljesíti az alapvető
Директива 1999/5/ЕС.
Magyar
[Hungarian]:
követelményeket
irányelvben
és
más
1999/5/EK
vonatkozó
meghatározott
Toto zařízení je
požadavky
ustanoveními Směrnice 1999/5/EC.
v
souladu se základními
Česky
[Czech]:
rendelkezéseket.
a
ostatními odpovídajícími
Dette utstyret er
i
samsvar med de
Norsk
[Norwegian]:
grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Dette udstyr er i overensstemmelse med
de væsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
Dansk
[Danish]:
Urządzenie jest zgodne
z
ogólnymi
Polski
[Polish]:
wymaganiami oraz szczególnymi warunkami
określonymi Dyrektywą UE: 1999/5/EC.
Dieses Gerät entspricht den grundlegenden
Deutsch
Anforderungen
und
den
weiteren
entsprechenden Vorgaben der Richtlinie
1999/5/EU.
[German]:
Este equipamento está em conformidade com
os requisitos essenciais e outras provisões
relevantes da Directiva 1999/5/EC.
Português
[Portuguese]:
See seade vastab direktiivi 1999/5/EÜ
olulistele nõuetele ja teistele asjakohastele
sätetele.
Eesti
[Estonian]:
Acest echipament este in conformitate
cu cerintele esentiale si cu alte prevederi
relevante ale Directivei 1999/5/EC.
Română
[Romanian]
This equipment is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
English:
Ta naprava je skladna z bistvenimi zahtevami
in ostalimi relevantnimi pogoji Direktive
1999/5/EC.
Slovensko
[Slovenian]:
Este equipo cumple con los requisitos
esenciales asi como con otras disposiciones
de la Directiva 1999/5/CE.
Español
[Spanish]:
Toto zariadenie je v zhode so základnými
Slovensky
[Slovak]:
požiadavkami
a
inými
príslušnými
nariadeniami direktív: 1999/5/EC.
Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε
τις ουσιώδεις απαιτήσεις και άλλες σχετικές
διατάξεις της Οδηγίας 1999/5/EC.
Ελληνική
[Greek]:
Tämä laite täyttää direktiivin 1999/5/EY
olennaiset vaatimukset ja on siinä asetettujen
muiden laitetta koskevien määräysten
mukainen.
Suomi
[Finnish]:
Cet appareil est conforme aux exigences
essentielles et aux autres dispositions
pertinentes de la Directive 1999/5/EC.
Français
[French]:
Denna utrustning är i överensstämmelse med
de väsentliga kraven och andra relevanta
bestämmelser i Direktiv 1999/5/EC.
Svenska
[Swedish]:
Wireless ADSL2+ Modem Router
11
Regulatory Information
Appendix C
For all products, the Declaration of Conformity (DofC) is
available through one or more of these options:
nessuna limitazione, eccetto per i paesi menzionati di
seguito:
Das Produkt kann in allen EU Staaten ohne Einschränkungen
eingesetzt werden (sowie in anderen Staaten die der EU
Direktive 1999/5/CE folgen) mit Außnahme der folgenden
aufgeführten Staaten:
•
•
•
A pdf file is included on the product’s CD.
A print copy is included with the product.
A pdf file is available on the product’s webpage.
select your country or region.Then select your product.
In the majority of the EU and other European countries,
the 2,4- and 5-GHz bands have been made available for
the use of wireless local area networks (LANs). Later in
this document you will find an overview of countries in
which additional restrictions or requirements or both are
applicable.
If you need any other technical documentation, see the
international”section, as shown later in this appendix.
Non-Wireless Equipment (ADSL Modems/Gateways)
The requirements for any country may evolve. Linksys
recommends that you check with the local authorities for
the latest status of their national regulations for both the
2,4- and 5-GHz wireless LANs.
The following standards were applied during the
assessment of the product against the requirements of
the Directive 1999/5/EC:
•
•
EMC: EN 55 022 and EN 55 024
Safety: EN 60950-1
The following countries have restrictions and/or
requirements in addition to those given in the table
labeled “Overview of Regulatory Requirements for Wireless
LANs”:
CE Marking
For the Linksys products such as the ADSL modems/
gateways, the following CE mark is added to the
equipment.
Denmark
In Denmark, the band 5150 - 5350 MHz is also allowed for
outdoor usage.
I Danmark må frekvensbåndet 5150 - 5350 også anvendes
udendørs.
France
Wireless Equipment (Wireless-N/G/A/B Products)
For 2,4 GHz, the product should not be used outdoors
in the band 2454 - 2483,5 MHz. There are no restrictions
when used in other parts of the 2,4 GHz band OR when
details.
The following standards were applied during the
assessment of the product against the requirements of
the Directive 1999/5/EC:
•
•
•
Radio: EN 300 328 and/or EN 301 893 as applicable
EMC: EN 301 489-1, EN 301 489-17
Pour la bande 2,4 GHz, l’ équipement ne doit pas être
utilisé en extérieur dans la bande 2454- 2483,5 MHz. Il
n’y a aucune restriction pour son utilisation dans d’autres
parties de la bande des 2,4 GHz ainsi que pour une
utilisation en intérieur. Consultez http://www.arcep.fr/
pour de plus amples détails.
Safety: EN 60950-1 and either EN 50385 or EN 50371
For the Linksys Wireless-N, -G, -B, and/or -A products, the
following CE mark, and class 2 identifier are added to the
equipment.
Italy
This product meets the National Radio Interface and
the requirements specified in the National Frequency
Allocation Table for Italy. Unless this 2,4-GHz wireless LAN
product is operating within the boundaries of the owner’s
property, its use requires a “general authorization”.
Bands 5150-5350 MHz and 5470-5725 MHz require
general authorization if used outdoors. Please check
http://www.comunicazioni.it/it/ for more details.
National Restrictions
This product may be used in all EU countries (and other
countries following the EU directive 1999/5/EC) without
any limitation except for the countries mentioned below:
Ce produit peut être utilisé dans tous les pays de l’UE (et dans
tous les pays ayant transposés la directive 1999/5/CE) sans
aucune limitation, excepté pour les pays mentionnés ci-
dessous:
Questo prodotto è conforme alla specifiche di Interfaccia
Radio Nazionali e rispetta il Piano Nazionale di ripartizione
delle frequenze in Italia. Se non viene installato all’interno
del proprio fondo, l’utilizzo di prodotti Wireless LAN a
Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti
gli altri paesi che seguono le direttive EU 1999/5/EC) senza
Wireless ADSL2+ Modem Router
12
Regulatory Information
Appendix C
2,4 GHz richiede una “Autorizzazione Generale”. L’utilizzo
all’aperto delle bande di frequenza 5150-5350 MHz e
5470-5725 MHz è soggetto ad autorizzazione generale.
Third-Party Software or Firmware
The use of software or firmware not supported/provided
by Linksys may result that the equipment is no longer
compliant with the regulatory requirements.
Consultare
per
maggiori dettagli.
Technical Documents on
Latvia
Follow these steps to access technical documents:
The outdoor usage of the 2,4 GHz band requires an
authorization from the Electronic Communications Office.
2,4 GHz frekveču joslas izmantošanai ārpus telpām
nepieciešama atļauja no Elektronisko sakaru direkcijas.
in your web browser.
2. Select the country or region in which you live.
3. Click the Products tab.
Notes:
4. Select the appropriate product category.
5. Select the product sub-category, if necessary.
6. Select the product.
1. Although Norway, Switzerland and Liechtenstein are
not EU member states, the EU Directive 1999/5/EC has
also been implemented in those countries.
7. Select the type of documentation you want from the More
Information section.The document will open in PDF format
if you have Adobe Acrobat installed on your computer.
2. The regulatory limits for maximum output power are
specified in EIRP. The EIRP level (in dBm) of a device can
be calculated by adding the gain of the antenna used
(specified in dBi) to the output power available at the
connector (specified in dBm).
NOTE: If you have questions regarding
the compliance of this product or you
cannot find the information you need,
please contact your local sales office or visit
Product Usage Restrictions
This product is designed for indoor usage only. Outdoor
usage is not recommended, unless otherwise noted.
Outdoor usage may even be prohibited (see below).
2,4 GHz Restrictions
This product is designed for use with the standard, integral
or dedicated (external) antenna(s) that is/are shipped
together with the equipment. However, some applications
may require the antenna(s), if removable, to be separated
from the product and installed remotely from the device
by using extension cables. For these applications, Linksys
offers an R SMA extension cable (AC9SMA) and an R-TNC
extension cable (AC9TNC). Both of these cables are 9
meters long and have a cable loss (attenuation) of 5 dB. To
compensate for the attenuation, Linksys also offers higher
gain antennas, the HGA7S (with R-SMA connector) and
HGA7T (with R-TNC connector). These antennas have a
gain of 7 dBi and may only be used with either the R-SMA
or R-TNC extension cable.
Combinations of extension cables and antennas resulting
in a radiated power level exceeding 20 dBm (100 mW)
EIRP (2,4 GHz band) are illegal.
5 GHz Restrictions
Products that operate in any frequency within 5150 to
5350 MHz are restricted to indoor use only, in all European
countries except Denmark.
Wireless ADSL2+ Modem Router
13
Regulatory Information
Appendix C
Čeština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
User Information for Consumer Products Covered
by EU Directive 2002/96/EC on Waste Electric and
Electronic Equipment (WEEE)
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply
with this notice for all electronic products bearing the
following symbol:
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace
a
recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an derVerpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
Български (Bulgarian)
-
Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне
и
рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Wireless ADSL2+ Modem Router
14
Regulatory Information
Appendix C
Eesti (Estonian)
Euroopa Liidus asuvatele klientidele
-
Keskkonnaalane informatsioon
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
seadmeid, millel on tootel või pakendil käesolev sümbol
,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
lasautoridadeslocales. Aldesecharyreciclarcorrectamenteestos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Ελληνικά (Greek)
-
Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που
φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του
δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων,
οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την
υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη
του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές
αρχές, τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα
από το οποίο αγοράσατε το προϊόν.
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
Wireless ADSL2+ Modem Router
15
Regulatory Information
Appendix C
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
vandezeenandereelektrischeenelektronischeapparatuurviade
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese)
Klijenti fl-Unjoni Ewropea
-
Informazzjoni Ambjentali għal
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih
is-simbolu
fuq il-prodott u/jew fuq l-ippakkjar ma jistax
jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu
jindika li dan il-prodott għandu jintrema separatament minn ma’
l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
Polski (Polish) - Informacja dla klientów w Unii
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Europejskiej
środowiska
o
przepisach dotyczących ochrony
A
2002/96/EC számú európai uniós irányelv megkívánja,
hogy azokat termékeket, amelyeken, és/vagy amelyek
csomagolásán az alábbi címke megjelenik, tilos a többi
a
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/
szelektálatlan lakossági hulladékkal együtt kidobni. A címke
azt jelöli, hogy az adott termék kidobásakor a szokványos
háztartási hulladékelszállítási rendszerektõl elkülönített eljárást
kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos
és elektronikus berendezéseit a kormányzati vagy a helyi
hatóságok által kijelölt gyűjtõredszereken keresztül számolja
fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az
emberi egészségre potenciálisan ártalmas negatív hatások
megelõzésében. Ha elavult berendezéseinek felszámolásához
további részletes információra van szüksége, kérjük, lépjen
lub jego opakowaniu nie był wyrzucany razem z innymi
niesortowanymi odpadami komunalnymi. Symbol ten wskazuje,
że produkt nie powinien być usuwany razem ze zwykłymi
odpadami z gospodarstw domowych. Na Państwu spoczywa
obowiązek wyrzucania tego i innych urządzeń elektrycznych
oraz elektronicznych
przez władze krajowe lub lokalne. Pozbywanie się sprzętu
we właściwy sposób jego recykling pomogą zapobiec
w
punktach odbioru wyznaczonych
i
potencjalnie negatywnym konsekwencjom dla środowiska i
zdrowia ludzkiego. W celu uzyskania szczegółowych informacji
o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych
władz, służb oczyszczania miasta lub sklepu, w którym produkt
został nabyty.
kapcsolatba
a
helyi hatóságokkal,
a
hulladékfeldolgozási
szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.
Wireless ADSL2+ Modem Router
16
Regulatory Information
Appendix C
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenščina (Slovene)
stranke v Evropski uniji
-
Okoljske informacije za
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s
tem simbolom – na izdelku in/ali na embalaži z nesortiranimi
komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek
zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša
odgovornost je, da to in preostalo električno in elektronsko
opremo oddate na posebna zbirališča, ki jih določijo državne
separados.
O
símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
ustanove ali lokalne oblasti.
S
pravilnim odlaganjem in
recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali
trgovino, kjer ste izdelek kupili.
Suomi (Finnish) - Ympäristöä koskevia tietoja EU-
alueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produktbörkastasefterattdenavskiljtsfrånvanligthushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie
s
týmto
symbolom
likvidované spolu
na produkte a/alebo jeho balení nesmie byť
s
netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
WEB: For additional information, please visit
Wireless ADSL2+ Modem Router
17
Regulatory Information
Appendix C
Cisco-Linksys ADSL2+ Devices on Long Lines
Australia
ADSL2+ devices may not achieve the type of“high speed”
operation expected when attached to a line that is longer
than intended by the ITU-T Rec. G.996.1 ADSL standard
i.e. >3 km of 0.4mm cable or a shorter cable length with
several tails or multiples. If the device is installed in such
conditions and does not give the expected “download”
performance, then do not refer the matter to the Telecom
Fault Service or ADSL Helpdesk.
The following information applies if you use the product
within Australia.
Safety Notice
WARNING: To ensure compliance with
exposure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm from the body during use.
United States of America
The following information applies if you use the product
within the United States of America.
New Zealand
The following information applies if you use the product
within New Zealand.
FCC Statement
Telepermit Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
Thisdevicemaynotcauseharmfulinterference, and(2)this
device must accept any interference received, including
interference that may cause undesired operation.
The cabling between the phone port and the phone shall
not exceed 100 metres.
PTC200 General Warning
The grant of a Telepermit for any item of terminal
equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for
connection to its network. It indicates no endorsement
of the product by Telecom, nor does it provide any sort
of warranty. Above all, it provides no assurance that any
item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model,
nor does it imply that any product is compatible with all of
Telecom’s network services.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
Wireless Connectivity Security on Cisco-Linksys
ADSL2+ Devices
Setting up the security of the wireless connection
associated with ADSL2+ device is the user’s responsibility.
Telecom will take no responsibility for charges made to
user’s accounts due to poorly organized wireless security
allowing unknown users to connect to the Internet via this
device. Do not complain to the Telecom Fault Service or
Jetstream Helpdesk should this occur.
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment or
devices
•
•
Connect the equipment to an outlet other than the
receiver’s
Consult a dealer or an experienced radio/TV technician
for assistance
General Warning for Cisco-Linksys ADSL2+
Devices and ADSL2+ Capability
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device has been tested and found suitable to connect
to the Telecom ADSL2+ capability. This indicates only that
Telecom has accepted that this device complies with the
spectrum management plan for ADSL2+ on copper cable
and with simple voiceband compatibility tests included
in PTC273. It does not indicate that this device is fully
compatible with all services accessed via the ADSL2+
capability. Contact the supplier of the device when
issues occur. Do not call the Telecom Fault Service or the
Jetstream Helpdesk.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator and your body.
Wireless ADSL2+ Modem Router
18
Regulatory Information
Appendix C
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. IEEE
802.11b or 802.11g operation of this product in the USA is
firmware-limited to channels 1 through 11.
No repairs may be done by the customer. If trouble is
experienced with this equipment, please contact your
authorized support provider for repair and warranty
information. If the trouble is causing harm to the
telephone network, the telephone company may request
you remove the equipment from the network until the
problem is resolved. This equipment cannot be used on
telephone company provided coin service. Connection to
Party Line Service is subject to state tariffs.
FCC Part 68 Statement
This equipment complies with Part 68 of the FCC Rules. A
label is attached to the equipment that contains, among
other information, its FCC registration number and ringer
equivalence number. If requested, this information must
be provided to the telephone company.
Safety Notices
This equipment uses the following USOC Jack: RJ-11.
WARNING: To reduce the risk of fire, use only
No.26 AWG or larger telecommunication line
cord.
An FCC compliant telephone cord and modular plug
is provided with this equipment. This equipment is
designed to be connected to the telephone network or
premises wiring using a compatible modular jack, which
is FCC Part 68 compliant. Connection to the telephone
network should be made by using the standard modular
telephone jack.
WARNING: Do not use this product near water,
for example, in a wet basement or near a
swimming pool.
The REN is useful to determine the quantity of devices
that may be connected to the telephone line and still have
all of those devices ring when your telephone number is
called. In most, but not all areas, the sum of RENs should
not exceed 5. To be certain of the number of devices that
may be connected to the line, as determined by the total
RENs, contact the telephone company to determine the
maximum REN for the calling area.
WARNING: Avoid using this product during an
electrical storm. There may be a remote risk of
electric shock from lightning.
WARNING: This equipment will be inoperable
when main power fails.
If this equipment causes harm to the telephone network,
the telephone company may discontinue your service
temporarily. If advance notice is not practical, the
telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
WARNING: To ensure compliance with
explosure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm from the body during use.
The telephone company may make changes in its
facilities, equipment, operations, or procedures that could
affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order
for you to make the necessary modifications in order to
maintain uninterrupted service.
In the event this equipment should fail to operate
properly, disconnect the unit from the telephone line.
Try using another FCC approved device in the same
telephone jack. If the trouble persists, call the telephone
company repair service bureau. If the trouble does not
persist and appears to be with this unit, disconnect the
unit from the telephone line and discontinue use of the
unit until it is repaired. Please note that the telephone
company may ask that you disconnect the equipment
from the telephone network until the problem has been
corrected or until you are sure that the equipment is not
malfunctioning. The user must use the accessories and
cables supplied by the manufacturer to get optimum
performance from the product.
Wireless ADSL2+ Modem Router
19
Regulatory Information
Appendix C
Avis d’Industrie Canada concernant l’exposition aux radio-
fréquences :
Canada
The following information applies if you use the product
within Canada.
Ce matériel est conforme aux limites établies par IC
en matière d’exposition aux radiofréquences dans un
environnement non contrôlé. Ce matériel doit être installé
et utilisé à une distance d’au moins 20 cm entre l’antenne
et le corps de l’utilisateur.
Industry Canada Statement
This device complies with Industry Canada ICES-003 and
RSS210 rules.
L’émetteur ne doit pas être placé près d’une autre antenne
ou d’un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device. This device has been designed to operate
with an antenna having a maximum gain of 2dBi.
Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna
impedance is 50 ohms.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the EIRP is not more than required for successful
communication.
Industry Canada Radiation Exposure Statement:
Avis de non-responsabilité concernant les appar-
eils sans fil
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator & your body.
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Avis d’Industrie Canada
Cet appareil est conforme aux normes NMB003 et RSS210
d’Industrie Canada.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes :
1. il ne doit pas produire de brouillage et
2. il doit accepter tout brouillage radioélectrique reçu,
mêmesicebrouillageestsusceptibledecompromettre
le fonctionnement du dispositif. Le dispositif a été
conçupourfonctionneravecuneantenneayantungain
maximum de 2 dBi. Les règlements d’Industrie Canada
interdisent strictement l’utilisation d’antennes dont le
gain est supérieur à cette limite. L’impédance requise
de l’antenne est de 50 ohms.
Afin de réduire le risque d’interférence aux autres
utilisateurs, le type d’antenne et son gain doivent
être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure
au niveau requis pour obtenir une communication
satisfaisante.
3425-01414
090605-10_20-10C-AI
Wireless ADSL2+ Modem Router
20
|