Coleman Tent 2000001590 User Manual

Tm  
HOOLIGAN 3  
MOdeL 2000001590  
7. Assemble thin, black, shock-corded Vent Pole.  
8. Insert Vent Pole through  
sleeve at back of tent.  
(Fig. 5)  
9. Insert metal tip into  
Before you begin  
Vent Pole  
Sleeve  
Read all instructions before set up.  
• Select a level site clear of rocks, branches, and other hard or  
sharp objects, to install your tent.  
WARNING: Keep clear of overhead power lines.  
• Do not set up your tent under trees because of potential  
lightning strikes or falling tree limbs in inclement weather.  
• Secure with all stakes and guylines provided to prevent  
property damage or personal injury.  
• For best results in windy conditions, position narrow end of  
tent into the wind.  
• Enlist the help of at least one other person to assist you when  
it is time to assemble the tent.  
grommet. Go to opposite  
end of Vent Pole and  
gradually apply pressure to  
pole forming an arch then  
insert metal tip into grommet.  
(Fig. 6 & 6A)  
Back of Tent  
Fig. 5  
Fig. 6  
6A  
Pole descriptions  
To Attach Rainfly  
Pole  
Pole  
Pole  
1. Drape Rainfly over tent. make sure seams on Rainfly are  
facing down and centered over poles and the vestibule is  
over to door of the tent. (Fig. 7)  
description  
Qty.  
dia.  
Repair Kit Replacement Kit  
main Pole, black  
Vestibule Pole, grey  
2
1
8.5mm 5010000541  
8.5mm 5010000541  
5010000547  
5010000547  
NOTE: Hook and loop fasteners, located on seams of under-  
side of rainfly, should be centered over black poles.  
Vent Pole, black  
with pre-bent ferrules  
1
6.0mm 5010000639  
5010000639  
To Set Up Tent  
Rainfly  
1. Unfold tent and spread out on a clean, level surface with the  
door facing perpendicular to the wind direction. Unzip door.  
2. Assemble main Poles by interlocking the black, shock-cord-  
ed, sections.  
Vestibule  
over Door  
3. Insert main Poles through sleeves in top of tent. (Fig. 1)  
Fig. 1  
Front of Tent  
Back of Tent  
Door  
Fig. 7  
2. Fold Rainfly at front of tent back as shown in Fig. 8.  
3. Assemble Vestibule Pole by interlocking the grey, shock-  
corded, sections.  
4. Insert one end of grey Vestibule Pole into pin on metal loop  
located at either side of tent. (Fig. 8 & 8A)  
5. Go to opposite end of Vestibule Pole and gradually apply  
pressure to pole forming an arch. Insert pin into the pole end  
(Fig. 8 & 8A).  
main  
Pole  
Sleeve  
Sleeve  
main  
Pole  
4. Insert one end of black main pole into pin on metal loop  
located at either end of tent. (Fig. 2)  
5. Go to opposite end of main Pole and gradually apply pressure  
to pole forming an arch. Insert pin into  
the pole end (Fig. 2 & 3). Repeat for the  
remaining main Pole.  
Grey Vestibule Pole  
Hook & Loop  
Fasteners  
main  
Pole  
metal  
Loop  
& Pin  
Fig. 2  
Door  
Front of  
Tent  
Stake  
Stake  
Fig. 3  
Fig. 8  
6. Stretch out corners and sides of  
tent. Drive in stakes at an angle  
through the metal loops to help  
anchor the corners & sides of the  
tent. (Fig. 3 & 4)  
8A  
Fig. 4  
(continued on other side)  
 

Clarion Cassette Player AX410 User Manual
Cobra Electronics Automobile Alarm Series 3100 User Manual
Compaq Network Card 127453 B21 User Manual
Craftsman Air Compressor 92116474 User Manual
Cypress Computer Hardware CY8C23433 User Manual
Electro Voice Portable Speaker EVX 180A User Manual
Electro Voice Stereo Amplifier L 1000 User Manual
Excalibur electronic PDAs Smartphones 975 3 EFG User Manual
Garland Oven Salamander Broiler User Manual
Gitzo Camcorder Accessories GT3531 User Manual