Adaptec ASH-1233
ATA Adapter
User’s Guide
R
Adaptec Customer Support
If you have questions about installing or using your Adaptec product, check this
document first—you will find answers to most of your questions here. If you need
further assistance, use the support options listed below.
Technical Support Identification (TSID) Number
■
Before contacting Technical Support, you need your unique 12-digit TSID
number. The TSID number identifies your product and support status.
■
The TSID number is included on a white, bar-coded label, like the example
below.
Support Options
■
■
■
Search the Adaptec Support Knowledgebase (ASK) at ask.adaptec.com for
articles, troubleshooting tips, and frequently asked questions for your product.
For support via e-mail, submit your question to Adaptec's Technical Support
Specialists at ask.adaptec.com.
To order Adaptec products, including accessories and cables, call +1 408-957-7274.
Europe
■
■
German: Search the Adaptec Support Knowledgebase (ASK) at
ask-de.adaptec.com for articles, troubleshooting tips, and frequently asked
questions for your product.
For support via e-mail, submit your question to Adaptec's Technical Support
Specialists at ask-de.adaptec.com.
■
■
■
French: Search the Adaptec Support Knowledgebase (ASK) at ask-fr.adaptec.com
for articles, troubleshooting tips, and frequently asked questions for your product.
For support via e-mail, submit your question to Adaptec's Technical Support
Specialists at ask-fr.adaptec.com.
English: Search the Adaptec Support Knowledgebase (ASK) at ask.adaptec.com
for articles, troubleshooting tips, and frequently asked questions for your product.
For support via e-mail, submit your question to Adaptec's Technical Support
Specialists at ask.adaptec.com.
To order Adaptec products, including accessories and cables, go to
Japan
■
■
Search the Adaptec Support Knowledgebase (ASK) at ask.adaptec.co.jp.
ii
Limited 5-Year Hardware Warranty
1. Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from
defects in material and workmanship for a period of five (5) years from the date of purchase.
If the product should become defective within the warranty period, Adaptec, at its option,
will repair or replace the product, or refund the purchaser’s purchase price for the product,
provided it is delivered at the purchaser’s expense to an authorized Adaptec service facility
or to Adaptec.
2. Repair or replacement parts or products will be furnished on an exchange basis and will
either be new or reconditioned. All replaced parts or products shall become the property of
Adaptec. This warranty shall not apply if the product has been damaged by accident,
misuse, abuse or as a result of unauthorized service or parts.
3. Warranty service is available to the purchaser by delivering the product during the warranty
period to an authorized Adaptec service facility or to Adaptec and providing proof of
purchase price and date. The purchaser shall bear all shipping, packing and insurance costs
and all other costs, excluding labor and parts, necessary to effectuate repair, replacement or
refund under this warranty.
4. For more information on how to obtain warranty service, write or telephone Adaptec at 691
South Milpitas Boulevard, Milpitas, CA 95035, (800) 959-7274.
5. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCT WHICH HAS
BEEN DAMAGED AS A RESULT OF ACCIDENT, MISUSE, ABUSE, OR AS A RESULT OF
UNAUTHORIZED SERVICE OR PARTS.
6. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES WHICH NOW
OR HEREAFTER MIGHT OTHERWISE ARISE RESPECT TO THIS PRODUCT. IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFRINGEMENT SHALL (A) HAVE NO GREATER
DURATION THAN 5 YEARS FROM THE DATE OF PURCHASE, (B) TERMINATE
AUTOMATICALLY AT THE EXPIRATION OF SUCH PERIOD AND (C) TO THE EXTENT
PERMITTED BY LAW BE EXCLUDED. IN THE EVENT THIS PRODUCT BECOMES
DEFECTIVE DURING THE WARRANTY PERIOD, THE PURCHASER’S EXCLUSIVE
REMEDY SHALL BE REPAIR, REPLACEMENT OR REFUND AS PROVIDED ABOVE.
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION
LOSS OF DATA, ARISING FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
ARE NOT THE RESPONSIBILITY OF ADAPTEC AND, TO THE EXTENT PERMITTED BY
LAW, ARE HEREBY EXCLUDED BOTH FOR PROPERTY DAMAGE, AND TO THE
EXTENT NOT UNCONSCIONABLE, FOR PERSONAL INJURY DAMAGE.
7. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, AND SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.
8. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
iii
Software License Agreement
PLEASE READ CAREFULLY: THE USE OF THIS SOFTWARE IS SUBJECT TO THE SOFTWARE
LICENSE TERMS OF ADAPTEC, INC. AND OTHER LICENSORS WHOSE SOFTWARE MAY
BE BUNDLED WITH THIS PRODUCT.
BY YOUR USE OF THE SOFTWARE INCLUDED WITH THIS PRODUCT YOU AGREE TO THE
LICENSE TERMS REQUIRED BY THE LICENSOR OF THAT SOFTWARE, AS SET FORTH
DURING THE INSTALLATION PROCESS. IF YOU DO NOT AGREE TO THE LICENSE
TERMS APPLICABLE TO THE SOFTWARE, YOU MAY RETURN THE ENTIRE UNUSED
PRODUCT FOR A FULL REFUND.
In return for acquiring a license to use the Adaptec software, which may include software from
third party licensors and patches made available by Adaptec (“Software”), and the related
documentation, you agree to the following terms and conditions:
1. License. This Agreement grants you, the Licensee, a license to:
a. Use the Software on a single computer system, which is not intended for use by more
than five (5) users; and:
b. Make one copy of the Software in machine readable form solely for back-up purposes,
provided you reproduce Adaptec's copyright proprietary legends. Notwithstanding the
foregoing, the Software may be used on the home, laptop or other secondary computer
of the principal user of the Software, and an additional copy of the Software may be
made to support such use. As used in this license, the Software is “in use” when it is
either loaded into RAM or installed on a hard disk or other permanent memory device.
The Software may be “in use” on only one computer at any given time. (Different license
terms and fees are applicable for networked or multiple user applications.) As a specific
condition of this license, you agree to use the Software in compliance with all applicable
laws, including copyright laws, and that you will not copy, transmit, perform or
distribute any audio or other content using the Software without obtaining all necessary
licenses or permissions from the owner of the content.
2. Restrictions. You may not distribute copies of the Software to others or electronically
transfer the Software from one computer to another over a network. You may not post or
otherwise make available the Software, or any portion thereof, in any form, on the Internet.
You may not use the Software in a computer service business, including in time sharing
applications. The Software contains trade secrets and, in order to protect them, you may not
decompile, reverse engineer, disassemble, or otherwise reduce the Software to a human-
perceivable form. YOU MAY NOT MODIFY, ADAPT, TRANSLATE, RENT, LEASE, LOAN,
RESELL FOR PROFIT, DISTRIBUTE, NETWORK OR CREATE DERIVATIVE WORKS
BASED UPON THE SOFTWARE OR ANY PART THEREOF.
3. Ownership of Software. As Licensee, you own the media upon which the software is
recorded or fixed, but Adaptec and its licensors retain title and ownership of the Software
recorded on the original media and all subsequent copies of the Software, regardless of the
form or media in which or on which the original and other copies may exist. This license is
not a sale of the Software or any copy.
4. Confidentiality. You agree to maintain the Software in confidence and that you will not
disclose the Software to any third party without the express written consent of Adaptec. You
further agree to take all reasonable precautions to preclude access of unauthorized persons
to the Software.
5. Term. This license is effective until January 1, 2045, unless terminated earlier. You may
terminate the license at any time by destroying the Software (including the related
documentation) together with all copies or modifications in any form. Adaptec will have the
right to terminate our license immediately if you fail to comply with any term or condition
of this Agreement. Upon any termination, including termination by you, you must destroy
the Software (including the related documentation), together with all copies or
modifications in any form.
6. Special Terms Applicable to Databases. Where a database is included with the Software, you
acknowledge that it is licensed only in connection with the use of the Software to perform
disc creation, and that the database and all data derived therefrom must be maintained in
confidence in accordance with the provisions of Section 4. This license does not grant you
any rights to distribute or disclose such database or data.
iv
7. Limited Warranty. Adaptec and its Licensor warrant only that the media upon which the
Software is furnished will be free from defects in material or workmanship under normal
use and service for a period of thirty (30) days from the date of delivery to you. ADAPTEC
AND ITS LICENSORS DO NOT AND CANNOT WARRANT THE PERFORMANCE OR
RESULTS YOU MAY OBTAIN BY USING THE SOFTWARE OR DOCUMENTATION. THE
FOREGOING STATES THE SOLE AND EXCLUSIVE REMEDIES ADAPTEC AND ITS
LICENSORS WILL PROVIDE FOR BREACH OF WARRANTY. EXCEPT FOR THE
FOREGOING LIMITED WARRANTY, ADAPTEC AND ITS LICENSORS MAKE NO
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED, AS TO
NON-INFRINGEMENT OF THIRD PARTY RIGHTS, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow the exclusion of implied
warranties or limitations on how long an implied warranty may last, so the above
limitations may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
8. The entire liability of Adaptec and its licensors, and your exclusive remedy for a breach of
this warranty, shall be:
a. The replacement of any media not meeting the above limited warranty which is
returned to Adaptec; or:
b. if Adaptec or its distributor is unable to deliver replacement media which is free from
defects in materials or workmanship, you may terminate this Agreement by returning
the Software and your money will be refunded.
9. Limitation of Liability. IN NO EVENT WILL ADAPTEC OR ITS LICENSORS BE LIABLE TO
YOU FOR ANY INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES,
INCLUDING ANY LOST PROFITS, LOST SAVINGS, OR LOSS OF DATA, EVEN IF
ADAPTEC OR A LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY. Some states do not allow the
exclusion or limitation of special, incidental, or consequential damages, so the above
limitation or exclusion may not apply to you.
10. Export. You acknowledge that the laws and regulations of the United States and other
countries may restrict the export and re-export of the Software. You agree that you will not
export or re-export the Software or documentation in any form in violation of applicable
United States and foreign law.
11. Government Restricted Rights. The Software is subject to restricted rights as follows. If the
Software is acquired under the terms of a GSA contract: use, reproduction or disclosure is
subject to the restrictions set forth in the applicable ADP Schedule contract. If the Software is
acquired under the terms of a DoD or civilian agency contract, use, duplication or disclosure
by the Government is subject to the restrictions of this Agreement in accordance with
48 C.F.R. 12.212 of the Federal Acquisition Regulations and its successors and 49 C.F.R.
227.7202-1 of the DoD FAR Supplement and its successors.
12. General. You acknowledge that you have read this Agreement, understand it, and that by
using the Software you agree to be bound by its terms and conditions. You further agree that
it is the complete and exclusive statement of the agreement between Adaptec and you, and
supersedes any proposal or prior agreement, oral or written, and any other communication
between Adaptec and you relating to the subject matter of this Agreement. No additional or
any different terms will be enforceable against Adaptec unless Adaptec gives its express
consent, including an express waiver of the terms of this Agreement, in writing signed by an
officer of Adaptec. You assume full responsibility for the use of the Software and agree to
use the Software legally and responsibly. This Agreement shall be governed by California
law, except as to copyright matters, which are covered by Federal law. This Agreement is
deemed entered into at Milpitas, California by both parties. Should any provision of this
Agreement be declared unenforceable in any jurisdiction, then such provision shall be
deemed severable from this Agreement and shall not affect the remainder hereof. All rights
in the Software not specifically granted in this Agreement are reserved by Adaptec.
Should you have any questions concerning this Agreement, you may contact Adaptec by
writing to:
Adaptec, Inc.
Legal Department
691 South Milpitas Boulevard
Milpitas, California 95035
v
Regulatory Compliance Statements
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. However, if this
equipment does cause interference to radio or television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
■
■
Consult the dealer or an experienced radio/television technician for help.
Use a shielded and properly grounded I/O cable and power cable to ensure compliance of
this unit to the specified limits of the rules.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Adaptec, Inc.
ASH-1233
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
European Union Compliance Statement
This Information Technology Equipment has been tested and found to comply with
EMC Directive 89/336/EEC, as amended by 92/31/EEC and 93/68/EEC, in
accordance with:
■ EN55022 (1998) Emissions
■ EN55024 (1998) Immunity:
➐ EN61000-4-2 (1998) Electrostatic discharge: 4 kV contact, 8 kV air
➐ EN61000-4-3 (1998) Radiated immunity
➐ EN61000-4-4 (1995) Electrical fast transients/burst: 1 kV AC, 0.5 kV I/O
➐ EN61000-4-5 (1995) Surges 1 kV differential mode, 2 kV common mode
➐ EN61000-4-6 (1996) Conducted immunity: 3 V
➐ EN61000-4-11 (1994) Supply dips and variation: 30% and 100%
In addition, all equipment requiring U.L. listing has been found to comply with EMC
Directive 73/23/EEC as amended by 93/68/EEC in accordance with EN60950 with
amendments A1, A2, A3, A4, A11.
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
vi
In this Guide
System Requirements
Installation Checklist
Preparing Your ATA Disk Drives
Connecting Your ATA Disk Drives
Mounting ATA Disk Drives and Connecting Power Cables
Installing the Device Driver
5
6
8
9
Registering Your Adaptec ASH-1233 Adapter
Troubleshooting
19
20
The Adaptec ASH-1233 ATA adapter provides increased
performance with enhanced ATA technology. The Adaptec
ASH-1233 supports ATA/133 hard disk drives with data transfer
rates up to 133 MegaBytes (MB) per second, providing maximum
disk performance in systems that have a PCI bus.
This User's Guide explains how to install the Adaptec ASH-1233
adapter, connect ATA hard disk drives to it, and install the device
drivers for your operating system.
1
System Requirements
System Requirements
The minimum system requirements for the ASH-1233 adapter are:
■
■
Pentium II-266 MHz Processor or higher
®
®
Microsoft Windows 98SE, Windows Me, Windows 2000, or
Windows XP
■
Available PCI slot with bus-mastering enabled
Note: Refer to your system or motherboard documentation
for information on enabling bus-mastering.
■
■
At least one ATA drive and IDE cable
CD-ROM or DVD-ROM drive
This is Your Adaptec ASH-1233 Adapter
The Adaptec ASH-1233 adapter has the following features:
Primary IDE Connector
LED Connector
Secondary IDE Connector
PCI Connector
2
Installation Checklist
Installation Checklist
disk drives, perform these tasks, in order:
1
2
3
4
Install the ASH-1233 adapter. (See the next section below.)
Prepare your disk drives. (See page 5.)
Connect your disk drives to the ASH-1233 adapter. (See page 6.)
Mount your disk drives and connect power and LED cables.
(See page 8.)
5
Install the device drivers. (See page 9.)
Installing Your Adaptec ASH-1233 Adapter
You can install your Adaptec ASH-1233 adapter into a 32-bit or
64-bit PCI expansion slot.
Note: If you are installing the adapter into an existing system,
back up all data before continuing.
To install the ASH-1233 adapter:
1
Discharge any static electricity build-up before handling the
ASH-1233 adapter by touching a grounded metal object (such
as the exposed metal parts on the back of your computer).
Caution: Always handle the adapter by its edges or metal
bracket. Do not touch the gold PCI connector or any
components on the adapter.
!
2
Turn off power to the computer and disconnect the power cord.
Open the computer cabinet, following the manufacturer’s
instructions.
3
Installing Your Adaptec ASH-1233 Adapter
3
Locate an unused expansion slot and remove the slot cover.
Save the slot cover screw for use in Step 5.
Slot cover screw
Expansion slot
cover
64-bit PCI expansion slots
32-bit PCI expansion slots
4
Insert the ASH-1233 adapter in the PCI expansion slot. Press
down firmly until the adapter clicks into place. When installed
properly, the adapter should appear level with the expansion slot.
Note: Depending on the tightness of the PCI slot, gentle but
firm force may be required to insert the adapter.
5
Secure the adapter bracket with the slot cover screw you
removed in Step 3.
Do not close the computer cabinet, reattach the power cord, or
power on your computer yet. Continue with Preparing Your ATA
Disk Drives on page 5.
4
Preparing Your ATA Disk Drives
Preparing Your ATA Disk Drives
Because setup can vary from device to device or computer to
computer, always refer to your ATA disk drive and computer
documentation for specific instructions.
Note: If you refer to the ATA drive’s documentation for
installation instructions, return to this document to continue
with installation of the software included in your kit.
Before you begin, ensure that you have the correct cables for the
ATA disk drives you are installing. Refer to the disk drives’
documentation for more information on cables.
Setting Jumpers on ATA Disk Drives
If you are installing two hard disk drives, set up each drive as a
master. This is typically done by changing jumper settings on the
drive. The master setting is the factory default setting on most ATA
drives. Refer to your hard disk drive documentation to determine
the correct jumper setting for master operation.
If you are installing four hard disk drives, set up two drives as
master and the other two as slave. Mark the master and slave drives
so you remember which are which when you are connecting the
cables.
5
Connecting Your ATA Disk Drives
Connecting Your ATA Disk Drives
The ASH-1233 adapter supports up to four ATA disk drives in a
master/slave configuration. (See Setting Jumpers on ATA Disk Drives
on page 5 for more information.)
Connect each ATA disk drive to the ASH-1233 adapter using the
proper 40-pin IDE cable.
Note: The Adaptec ASH-1233 adapter does not support Cable
Select (CSEL) settings. You must change the jumper settings
to set drives as master or slave.
Connector (to Adapter)
Connector (to Slave)
Connector (to Master)
To connect your ATA disk drives, follow the instructions for your
specific drive configuration:
■
To install an ATA disk drive as the only device on a cable, see
page 7.
■
To install two ATA disk drives on the same cable, see page 8.
6
Connecting Your ATA Disk Drives
Connecting One ATA Disk Drive on a Cable
When you connect only one ATA disk drive to a cable, that disk
drive must be set as a master drive. (See Setting Jumpers on ATA Disk
Drives on page 5 for more information.)
To connect one ATA drive to the ASH-1233 adapter:
1
Connect the IDE cable to an IDE connector on the ASH-1233
adapter, being careful to match pin 1 of the cable to pin 1 of the
connector.
The cables and connectors are keyed. If the cable does not slide
easily into the connector, do not force it. Instead, reverse the
cable.
Note: The stripe along the edge of the cable indicates
Pin #1. If the cable does not slide easily into the connector,
reverse the cable.
2
Connect the other end of the IDE cable to a master drive, as
shown below on the left.
3
Repeat Step 1 and 2 to connect a second ATA disk drive to the
second IDE connector on the ASH-1233 adapter, as shown above
on the right. Both disk drives must be set as master drives.
Continue with Mounting ATA Disk Drives and Connecting Power
Cables on page 8.
7
Mounting ATA Disk Drives and Connecting Power Cables
Connecting Two ATA Disk Drives to the Same Cable
When you connect two ATA disk drives to a cable, one disk drive
must be set as the master, the other must be set as the slave. (See
Setting Jumpers on ATA Disk Drives on page 5 for more information.)
To connect two disk drives to the same cable:
1
2
3
Connect one end of an IDE cable to an IDE
connector on the ASH-1233 adapter.
.
Connect the other end of the IDE cable to the
ATA disk drive that is set as the master.
You can connect a maximum of four ATA disk
drives to your ASH-1233 adapter, as shown at
right.
Continue with Mounting ATA Disk Drives and Connecting Power
Cables on page 8.
Mounting ATA Disk Drives and Connecting
Power Cables
To complete the hardware installation:
1
Mount each ATA disk drive in an available drive bay inside
your computer (as shown below).
Refer to your computer and device documentation for
instructions on installing devices inside your computer.
8
Installing the Device Driver
2
Connect an LED cable from your computer’s motherboard to
the primary LED connector on your ASH-1233 adapter (shown
in the Figure on page 2).
3
4
Connect a power cable from your computer’s power supply to
each ATA disk drive.
Close your computer cabinet, reattach the power cord, then
power on your computer.
Continue with Installing the Device Driver on page 9.
Installing the Device Driver
Before you can begin using your ASH-1233 adapter and ATA
drives, you must install the device driver.
Follow the instructions provided for your operating system:
■
■
■
■
For Windows XP, see page 10.
For Windows 2000, see page 12.
For Windows Me, see page 15.
For Windows 98SE, see page 17.
Note: If you are installing your ASH-1233 adapter and ATA
drives as part of a fresh operating system installation, refer to
the Readme file on the CD for instructions.
9
Installing the Device Driver
Windows XP
When you power on your computer, Windows automatically
detects the new adapter and opens the New Hardware Installation
Wizard.
To complete the device driver installation:
1
2
Insert the Adaptec ASH-1233 CD into your CD-ROM drive.
In the Wizard, click Install the software automatically..., then
click Next.
3
4
If a message appears indicating that the driver is not digitally
signed, click Continue Anyway.
When the installation is complete, click Finish.
10
Installing the Device Driver
5
To verify that the adapter is installed correctly, right-click the
My Computer desktop icon, select Properties, click the
Hardware tab, then click the Device Manager button. Expand
SCSI and RAID Controllers and ensure that the controller is
listed, as shown below.
11
Installing the Device Driver
Windows 2000
When you power on your computer, Windows automatically
detects the new adapter and opens the New Hardware Installation
Wizard.
To complete the device driver installation:
1
2
Insert the Adaptec ASH-1233 CD into your CD-ROM drive.
In the Wizard, click Next.
3
Select Search for a suitable driver..., then click Next.
12
Installing the Device Driver
4
Select CD-ROM drives, then click Next.
5
Click Next again.
6
7
When the installation is complete, click Finish.
Restart your computer if you are prompted to do so.
13
Installing the Device Driver
8
To verify that the adapter is installed correctly, right-click the
My Computer desktop icon, select Properties, click the
Hardware tab, then click the Device Manager button. Expand
SCSI and RAID Controllers and ensure that the controller is
listed, as shown below.
14
Installing the Device Driver
Windows Me
When you power on your computer, Windows automatically
detects the new adapter and opens the New Hardware Installation
Wizard. To complete the device driver installation:
1
2
Insert the Adaptec ASH-1233 CD into your CD-ROM drive.
In the Wizard, select Automatic search for a better driver...,
then click Next.
3
When the installation is complete, click Finish.
15
Installing the Device Driver
4
To verify that the adapter is installed correctly, right-click the
My Computer desktop icon, select Properties, then click the
Device Manager tab. Select View devices by type, then expand
SCSI Controllers and ensure that the controller is listed, as
shown below.
16
Installing the Device Driver
Windows 98SE
Note: You may need your Windows 98SE CD during
installation.
When you power on your computer, Windows automatically
detects the new adapter and opens the New Hardware Installation
Wizard. To complete the device driver installation:
1
2
Insert the Adaptec ASH-1233 CD into your CD-ROM drive.
In the Wizard, click Next.
3
Click Search for the best driver..., then click Next.
17
Installing the Device Driver
4
5
6
Select CD-ROM drive, then click Next.
Click Next again.
When the installation is complete, click Finish.
18
Registering Your Adaptec ASH-1233 Adapter
7
To verify that the adapter is installed correctly, right-click the
My Computer desktop icon, select Properties, then click the
Device Manager tab. Select View devices by type, then expand
SCSI Controllers and ensure that the controller is listed, as
shown below.
Registering Your Adaptec ASH-1233 Adapter
To register your ASH-1233 adapter, go to register.adaptec.com.
19
Troubleshooting
Troubleshooting
If you have any problems using the Adaptec ASH-1233 adapter,
work through these troubleshooting suggestions:
■
■
■
Ensure that the ASH-1233 adapter is inserted evenly and
completely in the PCI slot.
Ensure that the PCI expansion slot is 5V and compliant with
PCI 2.2 or previous version, and supports Bus Mastering.
Check that the ASH-1233 adapter is detected during boot. If it is
not detected, try moving it to another available PCI slot.
■
■
Check that all ATA cables and power cables are connected.
Check the jumper settings on your ATA disk drives.
20
R
Adaptec, Inc.
691 South Milpitas Boulevard
Milpitas, CA 95035 USA
©2004 Adaptec, Inc.
All rights reserved. Adaptec and the Adaptec logo
are trademarks of Adaptec, Inc. which may be
registered in some jurisdictions.
Part Number: 513909-06, Ver. AA, LB 04/04
|