Xantech Speaker System DL25 User Manual

DESCRIPTION  
These small IR receivers have been designed for mounting in very small  
spaces. They may be mounted under shelf edges, cabinet ledges, in wall  
speakers, etc. – anywhere an inconspicuous appearance is desired. The high  
sensitivity of these receivers allows placement behind speaker grilles and still  
receive IR commands up to 60 feet away*.  
FEATURES  
Wire channel for clean installation.  
System testing red-talk-back LED.  
Includes 3-Terminal Block for easy extension to remote room locations.  
INSTALLATION INSTRUCTIONS  
SPECIFICATIONS  
Infrared carrier frequency bandwidth: 30 - 60 kHz.  
Reception range: Up to 60 feet.*  
Reception angle: +/- 60 degrees.  
Cable requirements: See “INSTALLATION” below.  
Max. Transmission length: 1 mile using 18 gauge wire.  
Maximum current output: 100mA.  
Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.  
Dimensions: 2.55” x 0.55” x 0.35” (65mm x 14mm x 9mm).  
Power requirements: +12VDC, 10mA.  
DL25  
Dinky Link™ Surface Mount  
Standard IR Receiver  
* Depending on remote control output strength and ambient conditions.  
MOUNTING  
The IR receiver can be mounted to any flat surface, using the two-sided  
adhesive tape supplied. Two screws are included for mounting the 3-terminal  
block provided with the IR receiver.  
An additional feature is a wire channel on the rear of the surface mount IR  
receiver. This will give the installer the ability to provide clean wire dressing in  
any direction.  
1
 
TROUBLE SHOOTING:  
Limited Warranty  
Xantech® warrants its products to be free of defects in materials or workmanship. This is a  
Limited Lifetime warranty from the date of purchase by the original consumer. Any products  
returned to Xantech and found to be defective by Xantech within the warranty period will be  
repaired or replaced, at Xantech’s option, at no charge. Xantech will not be responsible for the  
actual cost of installation or removal of the product, nor for any incidental or consequential  
damages. Some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitation may not apply to you. This warranty gives you specific legal  
rights. You may have additional legal rights that vary from state to state.  
1. Perhaps the most common problem you may encounter is stray IR  
(infrared) or RF (radio frequency) interference preventing proper  
operation of the controlled equipment.  
Fluorescent, Compact Fluorescent, Neon or Halogen lights,  
Neon Art, and light dimmers.  
Direct or reflected sunlight.  
Infrared security sensors (active types).  
RF radiation from TV sets that may be close to the Dinky Link  
IR Receiver.  
2. You can confirm the source of the interference by temporarily turning  
off TV sets, isolating the Dinky Link IR Receiver from all sunlight and  
turning off all lights, light dimmers and Infrared security systems.  
Then check to see if the Dinky Link IR Receiver operates the  
component.  
Sometimes interference will cause the red Talk-Back LED on  
the front of the Dinky Link IR Receiver to blink dimly,  
intermittently, or continuously.  
The Talk-Back Led should only blink when you are sending  
infrared commands to the Dinky Link IR receiver from a  
remote control.  
It may be necessary to move either the interfering source of  
the Dinky Link IR Receiver to achieve proper operation.  
3. If the Talk-Back LED or the 283D Emitters do not blink when you are  
sending IR commands to the Dinky Link IR Receiver from a remote  
control, check the following:  
Make sure the power supply is plugged securely into a live  
AC electrical outlet.  
Be sure the stereo mini plug of the Dinky Link IR Receiver is  
plugged into the “IR RCVR” jack on the CB12 Connecting  
Block, not into the “OUT” jack.  
Check to see that all the mini plugs are properly seated into  
the mini jacks on the CB12 Connecting Block.  
4. If the 283D Emitters blink, but the component does not respond,  
reposition the 283D Emitter(s). They may not be located directly over  
the component’s infrared receiving “window”. Consul the owner’s  
manual of the unit or the manufacturer for the exact location of the  
infrared “window”.  
Xantech Corporation  
13100 Telfair Ave., Sylmar CA 91342 | Xantech.com  
Installation Instructions, DL25 © 2009 Xantech Corporation  
Document # 08905291B  
This document is copyright protected. No part of this manual may be copied or reproduced in any  
form without prior written consent from Xantech Corporation. Xantech Corporation shall not be  
liable for operational, technical, or editorial errors/omissions made in this document.  
4
5
 

Weed Eater Trimmer 530163513 User Manual
Weider Home Gym WEBE05920 User Manual
Weslo Treadmill WLTL018060 User Manual
Weslo Treadmill WLTL373080 User Manual
Whirlpool Refrigerator 2205958 User Manual
Woods Equipment Lawn Mower Accessory 211718 User Manual
Xerox All in One Printer 423 428 User Manual
Yamaha Car Amplifier DSP A1 User Manual
Zanussi Microwave Oven MW522D User Manual
Zebra Technologies Printer P110I User Manual