ELECTRONIC
ELECTRIC AND GAS
DRYERS
Use & Care Guide
For questions about features, operation/performance,
parts accessories or service, call: 1-800-253-1301
or visit our website at...www.whirlpool.com
Table of Contents...........................................................................2
8314840B
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
•
•
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic
precautions, including the following:
■ Read all instructions before using the dryer.
■ Do not repair or replace any part of the dryer or
attempt any servicing unless specifically recom-
mended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
■ Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
■ Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
■ Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
■ Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
■ Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children.
■ Clean lint screen before or after each load.
■ Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
■ Before the dryer is removed from service or dis-
carded, remove the door to the drying compart-
ment.
■ The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
■ Do not reach into the dryer if the drum is moving.
■ See Installation Instructions for grounding require-
■ Do not install or store the dryer where it will be
ments.
exposed to the weather.
■ Do not tamper with controls.
SAVE THESE INSTRUCTIONS
4
PARTS AND FEATURES
1.
4.
5.
2.
3.
6.
1. Control panel
Additional features your dryer has:
End of Cycle Signal selector
WRINKLE SHIELD™ selector
SENSEON™ electronic sensor
Drying rack
2. Model and serial number label
3. Dryer drum
4. Lint screen
5. Exhaust grill
6. Wide-opening door
Drum light
5
3. The exhaust vent can be routed up, down, left, right, or
straight out the back of the dryer. Space requirements are
listed in your Installation Instructions.
CHECKING
YOUR VENT
Your dryer must be properly installed and vented to achieve
maximum drying efficiency and shorten drying times. Use the
minimum recommended installation clearances (found in your
Installation Instructions) to avoid blocking the flow of combustion
and ventilation air. Refer to your Installation Instructions for more
information.
4. Use the straightest path possible when routing the exhaust
vent. Use the fewest number of elbows and turns. Allow
room when using elbows or making turns. Bend vent
gradually to avoid kinking.
Fire Hazard
Use a heavy metal vent.
5. Use duct tape to seal all joints. Do not use screws to secure
vent. Lint may catch on screws.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in
death or fire.
If the dryer is not properly installed and vented, it will not be
covered under the warranty.
6. Clean exhaust vent periodically, depending on use, but at
least every 2 years, or when installing your dryer in a new
location.
NOTE: Service calls caused by improper venting will be paid for
by the customer, whether it was a paid installation or self-
installed.
■
Disconnect vent from the dryer and clean one section at a
time until you reach the exhaust hood.
1. Do not use plastic vent or metal foil vent. Use 4 in. (10.2 cm)
metal or flexible metal vent. Do not kink or crush flexible
metal vent. It must be completely extended to allow adequate
exhaust air to flow. Check vent after installation. Refer to your
Installation Instructions for proper length requirements of
vent.
■
To clean out lint, use the hose attachment on your
vacuum, or a pole or wire with a feather duster or rag
attached.
■
■
Be sure the flapper on the outside end of vent moves
freely.
When cleaning is complete, be sure to follow the
Installation Instructions supplied with your dryer for final
product check.
2. Use a 4 in. (10.2 cm) exhaust hood. Smaller hoods increase
drying times.
4"
(10.2 cm)
4"
(10.2 cm)
6
Starting Your Dryer
USING
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping. The following steps
provide an overview for operating your dryer. Specific directions
for each step are contained in the following sections.
YOUR DRYER
1. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
Explosion Hazard
2. Select one of the Automatic or Timed Cycles. Use the Heavy
Duty or Normal cycles to dry most heavyweight and medium
weight loads. (See “Cycle Descriptions.”)
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in
death, explosion, or fire.
3. For Automatic Cycles, select one of the five levels of dryness
by pressing the up or down arrows. (See “Cycle
Descriptions.”)
4. For Timed Cycles only, select one of six temperature settings.
(See “Cycle Descriptions.”)
5. Select the WRINKLE SHIELD™ setting, if desired. (See
“Additional Features.”)
6. Select the End of Cycle Signal, if desired. The signal is helpful
when drying permanent press or synthetics. Promptly remove
these items from the dryer at the end of the cycle to prevent
wrinkles. (See “Additional Features.”)
7. Push the START pad.
Fire Hazard
No washer can completely remove oil.
Stopping, Pausing and Restarting
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
You can stop your dryer anytime during a cycle.
To stop your dryer
Press PAUSE/CANCEL twice.
Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
To restart your dryer
1. Close the door.
Failure to follow these instructions can result in
death or fire.
2. Select a new cycle and temperature (if an option with your
cycle.)
3. Push START.
To pause your dryer
Open the door or press PAUSE/CANCEL once. Press START to
resume the cycle. Dryer will stop if more than five minutes have
elapsed since the dryer was stopped.
7
■
■
Use a no heat (air) setting for rubber, plastic or heat sensitive
fabrics.
Loading Clothes
Line dry bonded or laminated fabrics.
Load clothes loosely into the dryer. Do not pack the dryer. Allow
space for clothes to tumble freely. The following chart shows
examples of balanced loads that would allow for proper tumbling.
If you are unsure of the temperature to select for a load, select
the lower setting rather than the higher setting
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
Heavy work
clothes
3 pair of pants, 4 pair of jeans, 2 pair of
overalls, 3 shirts
Delicates
3 camisoles, 1 robe, 4 slips,
6 undergarments, 2 sets of sleepwear,
1 child’s outfit
CYCLE DESCRIPTIONS
Towels
10 bath towels, 10 hand towels, 14 wash
cloths, 1 bath mat
Mixed Load
3 double sheets, 4 pillowcases,
8 T-shirts, 6 pair of shorts, 2 blouses,
8 handkerchiefs
Drying, Cycle and Temperature Tips
Select the correct cycle and temperature for your load.
Dryer tips
■
Press firmly in the center of the pad.
■
The indicator light next to the pad will light up when a
selection is valid.
■
■
■
A short tone will sound when a selection is valid.
Three short tones will sound when a selection is not valid.
After your first use, your dryer “remembers” the Dryness
level, WRINKLE SHIELD™ setting and End of Cycle Signal
setting you selected.
Automatic Cycle(s)
Use your Automatic Cycles to dry most loads. Your dryer uses
the SENSEON™ Drying System. Electronic sensors measure the
temperature of the exhaust to increase or decrease drying
temperatures for faster reaction time and tighter temperature
control. Your two most frequently used cycles, Heavy Duty and
Normal, are enhanced with the SENSEON system to provide the
shortest drying time.
■
■
If you press and hold the pad with either the Temperature
selector, the End of Cycle Signal selector or the More Dry or
Less Dry arrows, you will advance the settings.
If you press and hold the Less Time or More Time arrows in
the Timed Cycles, the time will advance in five minute
intervals.
Drying tips
After drying a load in any of the Automatic Cycles, check the
dryness.
■
Follow care label directions when they are available.
■
If the load is drier than you like, press the down arrow to
select a setting closer to Less Dry the next time you dry a
similar load.
■
If you use fabric softener sheets, use only ones labeled as
“dryer safe.” Follow package instructions.
■
■
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
■
If a load is not as dry as you like, complete drying using a
Timed cycle. Press the Up arrow to select a setting closer to
More Dry the next time you dry a similar load.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle.
NOTE: The Up and Down arrows are located next to the
Automatic Cycles pads.
To use the Automatic Cycles
1. Press the desired AUTOMATIC CYCLES pad.
Cycle tips
Use the Timed Dry cycle with the Air Only (no heat)
■
2. Press the Up or Down arrows to select from five levels of
Temperature setting for rubber, plastic or heat sensitive
fabrics.
More Dry or Less Dry, if desired.
3. Select the WRINKLE SHIELD™ setting, if desired.
Temperature tips
If your dryer has multiple heat settings:
4. Press the Bell symbol to select the End of Cycle Signal
Volume.
■
Use a high heat setting for drying heavyweight items such as
towels and work clothes.
5. Press START.
NOTE: The Estimated drying time varies from the actual drying
time with an Automatic cycle. The type of fabric, size of the load,
and the dryness selected affect drying time. See “Drying, Cycle
and Temperature tips.”
■
Use a medium heat setting for drying medium-weight items
such as sheets, underwear, permanent press fabrics, and
some knits.
■
Use a low heat setting for drying lightweight items such as
lingerie, blouses, dresses, and some knits.
8
Heavy Duty with the SENSEON™ Drying System
Touch Up
Select this cycle to thoroughly dry heavyweight items such as,
jeans, corduroys or work clothes. The temperature is
automatically set at High.
Use your Touch Up cycle to remove wrinkles from clean clothes
packed tightly in a suitcase or closet. You can also use Touch Up
to complete dry if items are still damp after the Automatic cycle.
The Touch Up cycle is preset to 20 minutes at Medium High heat.
You can select a different time or temperature, if desired.
Normal with the SENSEON™ Drying System
Select this cycle to evenly dry sturdy casual clothes such as,
khakis and cotton jerseys. The temperature is automatically set at
Medium High.
Rack Dry
Use your Rack Dry cycle with the drying rack to dry items that do
not require tumbling.
Permanent Press/Casual
The Rack Dry cycle is preset to 30 minutes at Medium Heat. (See
“Drying Rack”.) Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
Select this cycle to dry medium to lightweight synthetic or no-iron
items such as, sheets, shirts or dresses. The temperature is
automatically set at Medium.
NOTE: The Drying Status lights will not operate during the Rack
Dry cycle. The WRINKLE SHIELD™ setting is not a selectable
option with the Rack Dry Cycle.
Knits
Select this cycle to gently dry washable knit items such as,
blouses, sweaters and lingerie. The temperature is automatically
set at Low.
Favorite Cycle
Use the Favorite Cycle to select the cycle, amount of added
drying time, temperature (on Timed Cycles ONLY) and the
options of the WRINKLE SHIELD™ setting or End of Cycle Signal
you use most frequently and store them for future use.
Delicates
Select this cycle to extra gently dry items such as, exercise wear,
sheer curtains or lace. The temperature is automatically set at
Extra Low.
To store a cycle for future use with the Automatic Cycles
1. Select an Automatic Cycle.
Timed Cycles
2. Select one of five levels of dryness by pressing the up or
Your dryer has three Timed Cycles: Touch Up, Rack Dry and
Timed Dry. Each cycle has a preset time and temperature setting.
You can customize your Timed Cycles by adding options.
down arrows.
3. Select the WRINKLE SHIELD setting, if desired.
4. Select the volume on the End of Cycle Signal, if desired.
NOTE: If the load is not wet, several of the Drying Status lights
will not be activated when using the Timed Cycles.
5. Press the Heart symbol and hold for 2 seconds until you hear
a beep.
To add options to the Timed Cycles
1. Press the desired TIMED CYCLES pad.
6. Press START.
To reuse this cycle
1. Press the Heart symbol.
2. Press START.
To store a cycle for future use with the Timed Cycles
1. Select a Timed Cycle.
2. Press the MORE TIME arrow to select more time, or press the
LESS TIME arrow to deselect time.
3. Press the TIMED CYCLES SELECT pad to select a
temperature.
2. Select the number of minutes of drying by pressing the More
Time or Less Time arrows.
3. Select one of six temperature settings by pressing the Timed
Cycles Select pad.
4. Select the WRINKLE SHIELD setting, if desired.
5. Select the volume on the End of Cycle Signal, if desired.
6. Press the Heart symbol and hold for 2 seconds until you hear
a beep.
4. Select the WRINKLE SHIELD™ setting, if desired.
7. Press START.
5. Press the Bell symbol to select the End of Cycle Signal, if
desired.
To reuse this cycle
1. Press the Heart symbol.
2. Press START.
6. Press START.
Timed Dry
Use your Timed Dry cycle to complete drying if items are still
damp after the Automatic cycle.
Select Timed Dry to thoroughly dry extra heavyweight and bulky
items such as, bedspreads, quilts and mattress pads or large
loads that require a long drying time. You may also use the Timed
Dry cycle for lightweight items such as lingerie or knits.
The Timed Dry cycle is preset to 40 minutes at High heat. You
can select a different time or temperature, if desired.
9
Air Only Setting
Additional Features
Use the Air Only setting for items that require drying without heat
such as rubber, plastic and heat sensitive fabrics. Press the
Timed Dry cycle and select Air Only on the temperature selector.
This chart shows examples of items that can be dried using the
Air Only setting.
You can customize your cycles by selecting different features. If
you change your mind, select a different feature.
WRINKLE SHIELD™ setting
Type of Load
Air Only setting*
Foam rubber - pillows, padded bras,
stuffed toys
20 - 30
20 - 30
40 - 50
10 - 20
Plastic - Shower curtains, tablecloths
Rubber-backed rugs
When you are unable to remove a load of clothes from the dryer
as soon as it stops, wrinkles can form. The WRINKLE SHIELD
setting periodically tumbles, rearranges and fluffs the load to
avoid wrinkles.
Olefin, polypropylene, sheer nylon
(*Minutes) Reset cycle to complete drying, if needed.
Select the WRINKLE SHIELD setting by pressing the On/Off pad
on the Drying Status bar. The WRINKLE SHIELD setting
periodically tumbles the load without heat for up to 120 minutes.
When using Air Only
■
■
■
Check to see that coverings are securely stitched.
Shake and fluff pillows by hand periodically during cycle.
Dry item completely. Foam rubber pillows are slow to dry.
End of Cycle Signal
If the End of Cycle Signal is selected, the signal sounds when a
cycle is complete. If the WRINKLE SHIELD™ setting is selected,
the signal sounds every few minutes. The signal stops when you
open the door.
Dryer Features
Time Display
When you select an Automatic cycle, the estimated time is
displayed in the Time Remaining window and the Estimated light
is lit.
When you select a Timed cycle, the actual time is diplayed in the
Time Remaining window.
Drying Status Lights
You can monitor the progress of your load with the Drying Status
lights.
Press the Bell symbol to select a Softer or Louder signal or to
turn the End of Cycle Signal off.
Drying Rack
Select this feature to dry items such as tennis shoes and pillows
without tumbling. The drum turns, but the rack does not move.
To use the drying rack
1. Slide rear pegs into the dimples on the back wall of the dryer.
Lower the front legs to rest on the dryer opening.
■
■
Sensing
The Sensing light flashes at the start of the load when the
electronic moisture sensor is searching for wetness.
Wet
Once the moisture sensor detects wetness in the load,
the Wet light flashes until the moisture sensor can no
longer detect wetness in the clothes.
2. Put the wet items on top of the rack. Leave space between
the items so air can reach all the surfaces. Close the door.
■
Damp
The Damp light flashes after the moisture sensor no
longer detects wetness in the clothes. At this point, the
clothes are approximately 80% dry. You may want to
remove lightweight items in a mixed load to prevent
overdrying or remove partially dry items to hang up to
save on ironing. The Damp light will flash for
approximately two minutes.
NOTE: Do not allow items to hang over the edge of the rack.
3. Select the Rack Dry cycle. Press the MORE TIME or LESS
TIME arrows, if desired. Press the TIMED CYCLES SELECT
pad to select a temperature. Items containing foam, rubber,
or plastic must be dried on a clothesline or by using an Air
Cycle. Press the START pad.
■
■
Drying/Cool Down
The Drying/Cool Down light will continue to flash until
Cool Down is completed. The Drying/Cool Down light will
also flash if a Timed Cycle has been selected and the
Sensing light does not detect any moisture in the clothes.
WRINKLE SHIELD™
The WRINKLE SHIELD™ setting light is lit when it is
selected. The light flashes after the Cool Down period is
complete. The WRINKLE SHIELD setting light will
continue to flash until the clothes are removed or the 120
minutes of the WRINKLE SHIELD system have expired.
NOTE: You must remove rack for normal tumbling. Do not
use automatic cycles with the drying rack.
10
This chart shows examples of items that can be rack dried. After
selecting the Rack Dry cycle, select the temperature setting and
drying time across from each item.
To wash
1. Wet both sides of lint screen with hot water.
2. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
Rack Dry
Temp
Time*
Wool Sweaters
Block to shape and lay flat on the rack Low
60
Stuffed toys or pillows
Cotton or polyester fiber filled
Low
60
3. Rinse screen with hot water.
4. Thoroughly dry lint screen with a clean towel. Replace
Stuffed toys or pillows
screen in dryer.
Foam rubber filled
Air Only
Air Only
90
90
Cleaning the Dryer Interior
Sneakers or canvas shoes
*(Minutes) Reset cycle to complete drying, if needed. (Drying time
will depend on amount of moisture items hold).
NOTE: If your model does not have a drying rack you can order
one by calling 1-800-253-1301 or by contacting the dealer from
whom you bought your appliance.
CARING FOR YOUR DRYER
Explosion Hazard
Use nonflammable cleaner.
Cleaning the Lint Screen
Failure to do so can result in death, explosion,
or fire.
Every load cleaning
The lint screen is located on the top of the dryer. Clean it before
each load. A screen blocked by lint can increase drying time.
To clean dryer drum
To clean
1. Make a paste with powdered laundry detergent and very
1. Pull the lint screen towards you. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint. Wet
lint is hard to remove.
warm water.
2. Apply paste to a soft cloth.
OR
Apply a liquid, non-flammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
3. Wipe drum thoroughly with a damp cloth.
4. Tumble a load of clean cloths or towels to dry drum.
2. Push the lint screen firmly back into place.
IMPORTANT:
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items inside
out to prevent dye transfer.
■
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
■
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other
towels, causing your dryer’s lint screen to fill up faster. Be
sure to remove lint from the lint screen before and after drying
new towels.
■
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. See “Checking Your
Vent.”
As needed cleaning
Laundry detergent and fabric softener residue can buildup on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Clean the lint screen with a nylon brush every six months or more
frequently if it becomes clogged due to a residue buildup.
11
Changing the Drum Light
TROUBLESHOOTING
If your dryer has a drum light, the dryer light automatically turns
on inside the dryer drum when you open the door.
First try the solutions suggested here and possibly avoid
the cost of a service call...
To change the drum light
1. Unplug dryer or disconnect power.
Message Codes
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right
corner of the cover. Remove the cover.
■
For error message “PF” (power failure), check the
following:
Is the dryer connected to the power supply?
Was the dryer connected to a power supply during
installation or a power failure?
Press START to resume operation or press PAUSE/CANCEL
to cancel the cycle.
Was the drying cycle interrupted by a power failure?
Press START to resume operation or press PAUSE/CANCEL
to cancel the cycle.
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt
appliance bulb only. Replace the cover.
■
■
For error message “E1” or”E2” (service codes):
Service is required, call for service.
4. Plug in dryer or reconnect power.
Clothes are not drying satisfactorily
Removing Accumulated Lint from Inside the
Dryer Cabinet
Check the following:
Is the lint screen clogged with lint?
Lint should be removed every two years, or more often,
depending on dryer usage. Cleaning should be done by a
qualified person.
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for
5-10 minutes. Hold your hand under the outside exhaust
hood to check air movement. If you do not feel air movement,
clean exhaust system of lint or replace exhaust vent with a
heavy metal vent. See your Installation Instructions.
Is the exhaust vent crushed or kinked? Replace with a heavy
metal vent. See your Installation Instructions.
Has a fuse blown, or a circuit breaker tripped? Electric dryers
use 2 household fuses or breakers. The drum may be turning
but you may not have heat.
Has an air dry cycle been selected? Select the right cycle for
the types of garments being dried (see “Drying, Cycle and
Temperature Tips”).
Is the automatic cycle ending early? The load may not be
contacting the electronic sensor strips, level the dryer.
For gas dryers, is the valve open on the supply line?
Are fabric softener sheets blocking the grill? Use only one
fabric softener sheet and only use it once.
■
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
■
■
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water
and with items that hold moisture (cottons).
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
12
■
■
Was the dryer overloaded?
Dryer will not run
Dry smaller loads that can tumble freely.
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. (see “Drying, Cycle and Temperature Tips”).
■
Check the following:
Is the power cord plugged in?
Has a fuse blown, or has circuit breaker tripped?
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
Odors
■
■
■
If the dryer is electric, is it being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
Was the START pad firmly pressed?
Is a cycle selected?
If the dryer is gas, there may be a gas leak:
Turn off the gas supply line, leave your house and then call
your local gas company.
Unusual sounds
■
■
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, re-wash the clothing and then dry it.
Is it a gas dryer?
The gas valve clicking is a normal operating sound.
Garment damage
Lint on load
■
Check the following:
Were zippers, snaps, and hooks left open?
■
■
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
Is the load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
■
■
Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.
Was the load overdried?
Use correct dryer settings for load type. (See “Drying, Cycle
and Temperature Tips”.) Overdrying can cause lint-attracting
static electricity.
■
■
Was paper or tissue left in pockets?
Clean out pockets before drying.
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and
laundering.
Stains on load or color change
■
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially-dried load can
stain garments.
■
■
Were items soiled when placed in the dryer?
Items should be clean before being dried.
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from
noncolorfast items.
Items shrinking
■
■
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type (See “Drying, Cycle and Temperature Tips”).
Loads are wrinkled
■
Was load removed from dryer at the end of the cycle?
Remove load as soon as tumbling stops.
13
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
®
only use FSP factory specified parts. These parts will fit right and
work right because they are made with the same precision used
to build every new WHIRLPOOL GOLD® appliance. To locate
factory specified replacement parts in your area, call our
Customer Interaction Center at 1-800-253-1301, or your nearest
designated service center.
For assistance
Call the Whirlpool Customer Interaction Center toll free:
1-800-253-1301.
Our consultants provide assistance with:
■
■
■
■
■
Features and specifications on our full line of appliances
Installation information
Use and maintenance procedures
Accessory and repair parts sales
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
■
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Corporation
Customer Interaction Center
c/o Correspondence Dept.
MD 8020
553 Benson Road
Benton Harbor, MI 49022-2400
Please include a daytime phone number in your correspondence.
14
®
WHIRLPOOL GOLD DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
®
with the product, Whirlpool Corporation will pay for FSP replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
FIVE-YEAR LIMITED WARRANTY
For five years from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
®
with the product, Whirlpool Corporation will pay for FSP replacement parts to replace the electronic control system if defective in
materials or workmanship.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in (10.16 cm) metal exhaust vent must be used.
Refer to the venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Any labor costs incurred during the Five-Year Limited Warranty.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Outside the 50 United States, this warranty does not apply.
Contact your authorized Whirlpool dealer to determine if
another warranty applies.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
If you need service, first see “Troubleshooting.” Additional help
can be found by checking “Assistance or Service,” or by calling
our Customer Interaction Center at 1-800-253-1301, from
anywhere in the U.S.A. or write: Whirlpool Corporation, Customer
Interaction Center, c/o Correspondence Dept., MD 8020, 553
Benson Road, Benton Harbor, MI 49022-2400.
03/00
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or
installation date for in-warranty service.
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label/plate, located on your appliance as shown in “Parts and
Features.”
8314840B
09/00
Printed in U.S.A
© 2000 Whirlpool Corporation. All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
|