INSTALLATION MANUAL
IP STANDARD MASTER STATION N-8510MS
Thank you for purchasing TOA's IP Standard Master
Station.
Please carefully follow the instructions in this manual to
ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
When the Unit is in Use
• Use the dedicated AC adapter or its equivalent for the unit. Note that the use of other adapter may cause a
fire.
2. GENERAL DESCRIPTION
The N-8510MS is an IP standard master station designed for use with TOA's packet intercom N-8000 system (IP network-
compatible intercom system) that employs the packet audio technology*.
By directly connecting the N-8510MS to a network (LAN or WAN), high quality hands-free or handset conversations
between IP stations, and paging broadcasts (paging calls) can be made. Once an emergency message has been
programmed into the station, it can be broadcast to the pre-programmed zones with the key operation or external control
input.
The ideal system for in-house or wide-area information transmission applications such as conversations between IP
stations and N-8000 system's stations, paging broadcasts (paging calls), periodical broadcasts, and background music
broadcasts can be built in conjunction with the N-8000EX or N-8010EX IP intercom exchange, or the N-8000MI Multi
interface unit.
Using an optional YC-280 Wall mounting bracket, the station can be mounted on a wall, or tilted for easy key operation
when used on a desktop.
* Technology related to audio transmission over a network.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
6. WALL MOUNTING
The optional YC-280 Wall mounting bracket is required.
The YC-280 can be mounted to a one-gang electrical box.
6.1. Mounting
YC-280 Wall mounting
bracket (optional)
Step 1. Install the YC-280 to the wall.
N-8510MS
Notes
• Use the appropriate screws for the construction
of wall.
Wall
surface
• Wood screws 3.5 x 20 are supplied with the
YC-280.
• No fitting screws for an electrical box are
supplied.
Use commercially available screws.
2
Step 2. Hang the station on the wall mounting bracket
hook to install.
1
Hook
Push down the station body in the arrow
direction shown at right.
Wood screw 3.5 x 20
(supplied with the YC-280)
6.2. Installation Completion Drawing
6.3. YC-280 Dimensional Drawing
Unit: mm
Unit: mm
148
4.6 x 6
Rubber foot mounting position
(desktop application)
2-ø4.5
60
YC-280
80
72.1
83.5
4.5 x 10
YC-280
100
7. DESKTOP INSTALLATION
The station can be used on a desk. In desktop installations, the front operation panel can be inclined 16˚ from the desk
surface for easier operation by attaching the YC-280 Wall mounting bracket to its bottom surface.
7.1. Attaching the Bracket
7.2. Installation Completion Drawing
Unit: mm
Step 1. Attach the four rubber feet to the YC-280's bottom surface.
205.2
Step 2. Hang the YC-280's hook on the station's wall bracket
mounting slot to install.
Push up the YC-280 in the arrow direction shown below.
N-8510MS
YC-280 Wall mounting bracket
YC-280
Rubber foot
(supplied with the YC-280)
Hook
8. WIRING
[Power supply connection]
N-8510MS rear
The following 2 methods are available for
supplying power to the station.
• From a DC 12 V AC adapter
• From an IEEE802.3af compliant PoE
switching hub
DC INPUT
CONTACT IN
LAN
(For connection, refer to the instruction
manual supplied with the switching hub.)
C
H
12V
400mA
Cable
[AC adapter connection]
1
Connect the AC adapter* .
Install the supplied ferrite
clamp on the AC adapter
cable by winding the
cable around the ferrite
clamp once.
Ferrite clamp (accessory)
1
* Use the AC adapter AD-1210P (optional) or its equivalent.
As for the usable adapter, consult your TOA dealer.
To network
[Network connection]
[Control line connection]
Can be connected to a network of
10BASE-T/100BASE-TX in auto-sensing.
Use a UTP category 5 straight-through
cable with an RJ-45 connector for this
connection.
Connect the external control equipment such
as a switch or sensor to this terminal.
Press down the desired push-in
terminal button with a tip of standard
driver, and insert the cable securely.
Note
When using a PoE hub, be sure to
connect equipment having a protective
earth terminal (or power cable with earth)
and ground the earth terminal. Failure to
do so may cause equipment malfunction.
11 mm
• Applicable cables are as follows.
COM
HOT
Conductor diameter:
ø0.4 – 1.3 mm (AWG16 – 26), Solid wire
ø0.7 – 1.4 mm (AWG16 – 22), Stranded wire
9. ACCESSORIES
10. OPTIONAL PRODUCTS
CD*2 .................................................. 1
Ferrite clamp ..................................... 1
AC adapter:
Wall mounting bracket: YC-280
AD-1210P*3
*2 Contains the N-8000 setting software program and the
N-8000 series instruction manual.
*3 Consult your TOA dealer when using an equivalent
adapter.
The Setup Launcher is automatically started when the
supplied CD-ROM is inserted into the PC's drive.
Note
If your PC's CD drive is not compatible with the
AutoRun function, the setup guide is not automatically
started even when the CD is inserted.
Traceability Information for Europe
(EMC directive 2004/108/EC)
Use either "Explorer" or "My Computer" to execute the
following files, or use [Start
enter the following command.
Manufacturer:
TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Run] in the Task Bar and
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg, Germany
<Drive where CD is placed> \index.html
For example, when the CD is placed in the "d" drive,
d:\index.html
133-06-295-10
|