NETWORK
TECHNOLOGIES
INCORPORATED
1275 Danner Dr
Aurora, OH 44202
Tel:330-562-7070
Fax:330-562-1999
NTI
USB-SUN USB TO SUN ADAPTER
INSTALLATION / USER GUIDE
M A N 0 1 5 R E V 1 1 / 2 3 / 0 1
Setup
When using the USB-SUN adapter to connect to an NTI KVM switch:
1. Connect one male 8 pin minDIN end of the SKTINT-xx-MM cable to a female 8 pin minDIN Keyboard and Mouse input port on the
NTI KVM switch being used (see Fig. 3). Switch the power ON to the KVM switch if it isn't already.
2. Connect the other male 8 pin miniDIN end of the SKTINT-xx-MM cable to the 8 pin miniDIN female port on the USB-SUN
adapter.
Mating Face of a 8 Pin miniDIN Female
Fig. 3
3. Connect the USB type B male connector of the USB-AB-0.5M-5T cable (see Fig. 4) to the USB type B female port on the USB-
SUN adapter.
4. Connect the USB type A male connector of the USB-AB-0.5M-5T cable (see Fig. 5) to a USB type A female port on the host
computer. Note: It is important to make this connection last, particularly if the host computer is already ON at the time of
connection.
USB Type A Male
USB Type B Male
Connector
Connector
Fig. 5
Fig. 4
When using the USB-SUN adapter to connect a SUN Keyboard and/or Mouse to a SUN CPU with a USB port:
1. Connect the 8 pin minDIN male connector of the SUN keyboard and mouse assembly into the female 8 pin miniDIN port
on the USB-SUN adapter.
2. Continue with steps 3 and 4 above.
2
PLEASE NOTE: It is necessary to configure the host (Sun) computer such that the Sleep Mode is not enabled. If the host computer
goes into sleep mode either automatically or manually, the user must reboot the host computer in order to resume use of the host
computer.
To disable the Sleep Mode, perform the following steps:
1.
2.
3.
4.
5.
Select "Power Manager"
Look for "Device Idle Time Before Power Saving Starts"
Select "Always ON"
Look for "Override Device Idle Time For:"
Make sure neither "Monitors " nor "Disks" are selected.
Technical Specifications
M a t i n g F a c e o f a 8 p i n m i n i D I N F e m a l e
Mating face of a USB Type B Female
2
1
4
8
6
7
4
5
3
3
2
1
Fig. 6
Fig. 7
PIN #
SIGNAL
+VCC
PIN #
SIGNAL
GND
1
2
3
4
1
2
3
4
5
6
7
8
- DATA
+DATA
GND
GND
+5
MOUSE
KYBD RCV
KYBD XMT
PWRN
+5
WARRANTY INFORMATION
The warranty period on this product (parts and labor) is one (1) year from the date of manufacture (indicated on the bottom of the
product). Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at
http://www.nti1.com for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.
C O P Y R I G H T
Copyright © 2001 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without
the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202
C H A N G E S
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the right
to make changes in the product design without reservation and without notification to its users.
SERIAL NO.:
INSPECTED BY:
DATE:
3
|