Verilux Indoor Furnishings VP02 User Manual

VP02  
 
IMPORTANT SAFETY INSTRUCTIONS  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT  
DISMANTLE. THERE ARE NO SERVICEABLE PARTS INSIDE.  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT  
EXPOSE THIS UNIT TO RAIN OR MOISTURE.  
The exclamation point within an equilateral triangle alerts  
the user to the presence of important operating and  
maintenance instructions in this owner’s guide.  
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR  
PERSONAL INJURY:  
Turn off/unplug and allow to cool before replacing bulb or cleaning.  
Light bulbs get HOT quickly! Do not touch the bulb while the lamp is  
on.  
Do not look directly at the lighted bulb.  
Do not operate the lamp in close proximity to flammable or  
combustible vapors, such as aerosol (spray) products or where  
oxygen is being administered.  
Use only the type of bulb and maximum wattage indicated by  
Verilux®.  
Never cover the lamp when it is in operation.  
2
 
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions – before using this lamp.  
2. Keep these instructions – for future reference.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this lamp in damp/humid or wet locations.  
6. For indoor use only.  
7. Clean only with dry cloth.  
8. Do not block any ventilation openings.  
9. Do not place near any heat sources such as radiators, heat  
registers, stoves, or other apparatus (including amplifiers) that  
produce heat.  
10. Do not defeat the safety purpose of the polarized plug. A polarized  
plug has two blades with one wider than the other. The wider blade  
is provided for your safety. If the provided plug does not fit in your  
outlet, consult an electrician for replacement of the obsolete outlet.  
11. Protect the power cord from being walked on or pinched particularly  
at plugs, convenience receptacles, and the point where it exits from  
the lamp.  
12. Only use attachments/accessories specified by the manufacturer.  
13. Unplug this lamp during lightning storms or when unused for long  
periods of time.  
14. If the lamp has been damaged in any way, such as power-supply  
cord or plug is damaged, liquid has been spilled or objects have  
fallen onto the lamp, the lamp has been exposed to rain or moisture,  
does not operate normally, or has been dropped, it should not be  
operated. There are no user serviceable parts within this lamp.  
SAVE THESE INSTRUCTIONS  
3
 
GENERAL PRECAUTIONS  
• Do not use with power supply voltage other than 120V AC  
• Avoid placing the lamp in areas that are dusty, humid/moist, lack  
ventilation, or are subject to constant vibration.  
• Not for use with light dimmers, timers, motion detectors, voltage  
transformers, or extension cords.  
• Do NOT use lubricating agent in bulb assembly.  
• The light bulb may become loose during transit. To reinstall the light  
bulb, see the bulb installation instructions on page 8.  
• Close supervision is recommended when this lamp is used by or  
near children, or others who may not understand the need for these  
precautions. Do not leave the lamp unattended during use.  
This product may cause interference with radios, cordless  
telephones, or devices that use a wireless remote control,  
such as televisions.  
This lamp has been tested and found to comply with Part 18 of the  
FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This lamp  
generates, uses, and can radiate radio frequency energy and, if  
not used in accordance with the instructions, may cause harmful  
interference to radio communications. If interference occurs try to  
correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the lamp and receiver.  
• Connect the lamp into an outlet on a circuit different from that to  
which the receiver is connected.  
• Move the lamp out of the line of sight of the remote control receiver.  
• Consult the dealer or an experienced radio/TV technician for help.  
Note: This product may cause interference to radio equipment  
and should not be installed near maritime safety communications  
equipment or other critical navigation or communication equipment  
operating between 0.45-30 MHz.  
4
 
SET-UP INSTRUCTIONS  
Unpacking  
Please remove all packaging material. Check the carton for the items  
pictured below:  
Note: For your convenience, the bulb has been pre-installed in the  
socket. However it may have loosened during transit. Please check to  
be sure it is fully seated in the socket (see page 8)  
5
 
SET-UP INSTRUCTIONS  
Attaching the Parabolic Grid Diffuser  
1. Remove protective packing from bulb.  
2. Remove grid diffuser from protective plastic bag.  
3. Insert plastic pegs at bottom of grid diffuser into openings near bulb  
socket and snap tab into place.  
TAB  
4. Plug lamp into a standard 110-120V outlet, simply open the lamp  
to switch it on and begin enjoying the benefits of Verilux® Natural  
Spectrum® light!  
Note: please allow a few minutes for the bulb to warm up to full  
illumination.  
Note: if bulb does not illuminate instantly, please refer to the  
troubleshooting section of this manual.  
6
 
CORD INSERTION  
The lamp cord may be stored completely or partially within the  
cavity at the back of the lamp.  
To insert the cord, simply close the lamp, place it on a level surface  
with its face down, turn the cord in a vertical position and insert the  
cord into the back of the lamp until all or part of the length of the  
cord is inserted.  
When it is fully inserted, the plug may be locked into the slot at the  
base of the insertion opening to avoid having the cord fall out during  
transit.  
7
 
BULB REPLACEMENT  
Bulb removal & replacement  
REMOVAL  
1. Unplug lamp from power source.  
2. To access the bulb, remove the grid diffuser by depressing the tab  
and lifting it out (see page 6)  
3. Firmly hold the bulb base (B) and pull bulb (C) from the socket in an  
outward motion.  
D
REPLACEMENT  
1. Unplug lamp from power source.  
2. Firmly hold base (B) and push  
bulb (C) into the socket (A).  
3. Be sure bulb is firmly seated in  
the socket (see below) and  
snapped into the metal  
bulb clip (D).  
C
B
A
4. Replace grid diffuser.  
Correctly Seated Bulb  
Incorrectly Seated Bulb  
No Gap  
Notice  
Gap  
8
 
TROUBLESHOOTING  
Before requesting service on your Verilux® lamp please read the  
following:  
• Make sure all power connectors, cords, and plugs are inserted fully  
and securely.  
• Be sure the bulb is securely seated in the socket. (See page 8)  
• Make sure there is power to the wall outlet or try another outlet – not  
connected to a dimmer.  
CARE & CLEANING  
Your Verilux® lamp is made from high quality materials that will last for  
many years with a minimum of care.  
Clean only with a soft dry cloth – DO NOT USE SOLVENTS OR  
CLEANERS CONTAINING ABRASIVES OR AMMONIA  
WARNING: To prevent risk of shock or personal injury  
when cleaning lamp, make sure you have turned off and  
unplugged the lamp, and allow sufficient time for the bulb  
to cool.  
9
 
WARRANTY  
Three-Year Limited Warranty  
This limited warranty is provided by:  
Verilux, Inc., Research Park, 9 Viaduct Road, Stamford, CT 06907  
Verilux® warrants this product to be free of defects in materials and  
workmanship for a period of three years from the invoice date of original  
retail purchase. During the limited warranty period, Verilux® will, at its  
option, repair or replace defective parts of this product, at no charge to  
you, subject to the following limitations. This warranty does not include  
any postage, freight, transportation, insurance, or delivery fee. This  
limited warranty does not cover damage, defect, or failure caused by or  
resulting from accidents, external destruction, alteration, modification,  
abuse, misuse, or misapplication.  
ATTENTION: When returning a product, be aware that damage during  
shipping is the responsibility of the purchaser and will void any warranty  
claim. We recommend that you insure the shipment by shipper when  
returning this product or any parts. Be sure to return product in original  
packaging.  
Note: Verilux® recommends using a quality surge suppressor on all  
electronics equipment. Voltage variations and spikes can damage  
electronic components in any system. A quality suppressor can  
eliminate the vast majority of failures attributed to surges and may be  
purchased at electronics stores.  
Due to ongoing improvements, actual product may have slight variations from the product  
described in this manual.  
10  
 
340 Mad River Park, Waitsfield, VT 05673  
1-888-544-4865  
Printed in Taiwan for: Verilux, Inc.  
© Copyright 2007 Verilux, Inc. All rights reserved.  
VP02-MAN-Rev2  
 

Teledex Telephone 600 0480 59 User Manual
Teledyne Blood Glucose Meter 100E User Manual
TOA Electronics Speaker SR EP4 User Manual
Tote Vision Computer Monitor LCD 800 User Manual
U Line Refrigerator 2275DWRCOL User Manual
Ultratec Snowshoes SILENT STORM DMX User Manual
Uniden Cordless Telephone D1780 2 User Manual
Vanguard Heating Indoor Fireplace WMH26TNB User Manual
Verilux Indoor Furnishings VD06 User Manual
Viking Burner F20921B User Manual