FLOOR LAMP
Please visit our web site at:
Call our Client
Relations Department at
INST
M
1-800-786-6850
(Representatives are available
Monday - Friday, 9 AM - 5 PM Eastern)
?
Research Park
9 Viaduct Road
Stamford, CT 06907
HEF1-MAN, rev2
Important Safety Instructions
Unpacking Your Lamp
1. Remove all pieces from box.
Thank you for purchasing the Verilux HappyEyes Floor Lamp
.
Locate 2 screws and tightening tool.
Please read the following safety information before using.
2. Detach red plastic pieces and store
them in the event you need to
return the lamp.
General Precautions
the product away from the
device, plug the product or
device into a different outlet,
or move the lamp out of the line
of sight of the remote control
receiver. This lamp complies
with part 18 of FCC.
The light bulb may become
loose during transit. To reinstall
the light bulb, see the bulb
replacement instructions.
•
This portable lamp has
a polarized plug (one blade
is wider than the other).
3. Important: To avoid scratching
the metal shaft, do not use a sharp
object to cut the plastic covering.
The clear plastic covering on the
shaft is specially designed to tear
away easily.
As a safety feature, this plug
will fit in a polarized outlet
only one way. If the plug
does not fit fully in the outlet,
reverse the plug. If it still
does not fit, contact a qualified
electrician. Never use with
an extension cord or adapter
unless plug can be fully
•
•
The HappyEyes Floor Lamp
is an electrical device.
DO NOT USE NEAR WATER
inserted. Do not attempt
to defeat this safety feature.
•
•
Before plugging in the Verilux
HappyEyes Floor Lamp, check
to make sure the voltage
corresponds with the main
voltage of your location
(120 volts).
Do not use the HappyEyes
Floor Lamp outside or in wet
locations such as bathrooms.
It is intended for indoor, dry
use only.
•
•
Not for use with light dimmers,
timers, or motion detectors.
This product may cause
interference with radios,
cordless telephones, or devices
that use a wireless remote
control, such as televisions.
If interference occurs, move
IMPORTANT NOTE:
Remove red plastic protective
pieces prior to assembly.
3
4
Assembly Instructions
Assembly Instructions (continued)
Read Instructions Carefully Before
4. Attaching the Parabolic Grid Diffuser
Assembly:
• Remove grid diffuser from protective
plastic bag
1. Remove lamp from box and packaging.
Remove red plastic protective pieces
from lamp shaft. NOTE: Please save
original packaging for repacking should
you need to return the product.
• Insert plastic pegs at bottom of
grid diffuser into openings near
bulb socket
• Snap tab into place
2. Set lamp base on the floor and insert
the lamp shaft over the base support
part until the screw holes line up as
shown in Fig.1. Insert the screw using
the tightening tool and turn clockwise
to tighten.
5. Plug lamp into outlet and turn on; if bulb
does not illuminate instantly, please refer
to the troubleshooting section of this manual.
3. Attach the lamp head gooseneck to
the shaft, tucking the wire into the shaft,
until the screw holes line up as shown
in Fig.1. Insert the screw using the
tightening tool and turn clockwise to
tighten. Should you have difficulty lining
up the base or head screw holes, refer
to the troubleshooting section of this
manual.
DO lift your lamp by the shaft
DO NOT lift the lamp by
the gooseneck
Close-up of screw hole
in the lamp base
Fig. 1
5
6
Bulb Replacement Instructions
Care & Cleaning
Your HappyEyes Floor Lamp is made from high quality materials
that will last for many years with a minimum of care. You may want
to periodically clean the lamp, using a mild non-abrasive cleaner
and soft cloth. When cleaning, make sure you have turned off and
unplugged the unit, and allowed sufficient time for the unit to cool.
Removal
1. Unplug lamp from power source.
D
2. To access to the bulb, remove grid
diffuser by depressing the tab and
lifting it out. (See page 6)
DO NOT USE SOLVENTS OR CLEANERS CONTAINING
ABRASIVES, OR AMMONIA BASED CLEANERS
3. Firmly hold bulb base (B) and pull
bulb (C) from the socket (A) in
an outward motion.
All moisture should be properly wiped away and dried prior to
restoring power.
B
C
Installation
A
1. Unplug lamp from power source.
2. Firmly hold base (B) and push
bulb (C) into the socket (A).
3. Be sure bulb is firmly seated in
the socket (see below) and snapped
into the metal bulb clip (D).
4. Replace grid diffuser.
Correctly seated bulb
Incorrectly seated bulb
No
gap
Notice
large
gap
7
8
Troubleshooting
Warranty
Before Requesting Service on Your Verilux Lamp, Please Read
the Following:
Three-Year Limited Warranty
This limited warranty is provided by:
Verilux, Inc., Research Park, 9 Viaduct Road, Stamford, CT 06907
•
Make sure all power connectors, cords, and plugs are inserted fully
and securely.
Verilux warrants this product to be free of defects in materials and
workmanship for a period of three years from the invoice date of
original retail purchase. During the limited warranty period, Verilux
will, at its option, repair or replace defective parts of this product, at no
charge to you, subject to the limitation. This warranty does not include
any postage, freight, transportation, insurance, or delivery fee. This
limited warranty does not cover damage, defect, or failure caused by
or resulting from accidents, external destruction, alteration,
modification, abuse, misuse, or misapplication.
•
•
Be sure the bulb is securely seated into the socket. (See page 7)
Unplug the lamp for a few minutes (this allows the electronic ballast
inside the lamp to reset).
•
Make sure there is power to the wall outlet or try another outlet.
Notice:When returning a unit, be aware that damage during shipping
is the responsibility of the purchaser and will void any warranty claim.
We recommend that you insure the shipment with your post office or
other shipping service when returning this unit or any parts. Be sure
to return product in original packaging.
Due to ongoing improvements, actual product may have slight variations from
the product described in this manual.
9
10
|