VEC258 Manual 3/03.qxp 1/23/07 5:18 PM Page i
VEC258
1 YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty,
other than those described herein.
CORDED, CORDLESS,
RECHARGEABLE COMPRESSOR
AND LANTERN LIGHT COMBO
This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of
defects in materials and workmanship for one year from the date of purchase without additional
charge. The warranty does not extend to subsequent purchasers or users. Vector Manufacturing,
Ltd. will not be responsible for any amount of damage in excess of the retail purchase price of the
product under any circumstances. Incidental and consequential damages are specifically excluded
from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to accessories or
damage to units from misuse or incorrect installation. Misuse includes wiring or connecting to
improper polarity power sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage
prepaid to Vector Manufacturing. Any defective product, other than accessories, that is returned
to Vector Manufacturing within 30 days of the date of purchase will be replaced free of charge. If
such a product is returned more than 30 days but less than one year from the purchase date,
Vector Manufacturing will repair the unit or, at its option, replace it free of charge.
If the unit is repaired, new or reconditioned replacement parts may be used, at Vector
Manufacturing’s option. A unit may be replaced with a new or reconditioned unit of the same or
comparable design. The repaired or replaced unit will then be warranted under the terms of the
remainder of the warranty period. The customer is responsible for the shipping charges on all
returned items after 30 days. During the warranty period, Vector Manufacturing, Ltd. will be
responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting
from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due
to usage or exposure to sunlight), accidents, damage during shipping to our service facility,
alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions for
care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department at
(954) 584-4446 or toll free at (866) 584-5504 for general repair information and charges if
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow
limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the exclusions or limitations stated herein may not apply. This warranty
gives the purchaser specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing technical support
by telephone, fax or mail. We suggest that you keep the original packaging in case you need to
ship the unit. When returning a product, include your name, address, phone number, dated sales
receipt (or copy) and a description of the reason for return and product serial number. After
repairing or replacing the unit, we will make every effort to return it to you within four weeks.
OWNER’S MANUAL
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector
Manufacturing. Enter “VEC258” as Model and "Corded, cordless, rechargeable compressor and
lantern light combo" as Product Type. All Vector Manufacturing, Ltd. products must be registered
within 10 days of purchase to activate this warranty. Mail the completed registration form, along
with a copy of the original sales receipt to:
& WARRANTY INFORMATION
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ
AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN INJURY AND/OR PROPERTY DAMAGE.
ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.
4140 SW 28th Way, Ft. Lauderdale, FL 33312
PH: 954-584-4446 • TOLL FREE: 866-584-5504 • Fax: 954-584-5556.
4140 SW 28th Way, FT. LAUDERDALE, FL 33312
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.
Tel 954-584-4446 • TOLL FREE: 866-584-5504 • Fax 954-584-5556
3/03
VEC258 Manual 3/03.qxp 1/23/07 5:18 PM Page 3
The compressor on/off switch controls operation of the compressor. It conveniently is
depressed and released to control inflation. An exact pressure is obtained by observing
the gauge and releasing the trigger when the correct pressure is achieved. For longer
inflation operations, the trigger lock can be moved laterally to lock the trigger in the
ON position. Pushing the trigger lock to the opposite direction releases the trigger
(OFF) and inflation stops.
1.
INTRODUCTION
Congratulations on selecting the Vector AirPro™ Model VEC258 Compressor &
Lantern Light Combo. This system is an advanced, high-pressure (up to 260 PSI), multi-
use air compressor system with unique features that set it far above the value and util-
ity of ordinary compressors for mobile use. It is supplied with a standard tire valve
chuck for filling auto, truck, bike, and motorcycle tires. Additionally, two different
adapters are supplied to inflate soccer balls, footballs, and popular inflatables. These
adapters are conveniently stored in a hatch in the compressor body. It is powered
from its own snap-on/off powerful battery, to be used anywhere it is needed. It can
also operate from a standard 12 volt DC electrical system found on: trucks, cars, boats,
airplanes, RVs and tractors, using the supplied DC power adapter. A supplied stan-
dard 110 volt AC charger recharges the battery when required. Typically, up to three
completely flat tires can be inflated before the snap-on battery has to be recharged.
2.
ADDITIONAL KEY FEATURES
• Trigger switch with lock to allow hands free operation
• Corded-includes a DC power adapter for use with standard 12 volt DC power supply
• Battery pack includes non-spillable, maintenance-free, heavy duty, sealed,
high-density, lead-acid battery
• Requires no maintenance (other than recharging and cleaning) for optimum
operation
A separate lantern light shares the battery pack and DC power adapter. The light is
versatile and provides a spotlight, fluorescent area light, and emergency flasher.
•
Supplied 110 volt AC charger is Underwriter Laboratories (UL) safety tested and listed
• Battery charging LED on battery automatically activated during AC recharge
• Analog pressure gauge to 260 PSI compressor
• Nozzle hatch for storing nozzles in compressor
• 3 nozzles for inflator
A customer can purchase extra snap-on battery packs if completely cordless operation
is required (Part VEC194). Operating these appliances with the snap-on DC power
adapter is ideal for use with Vector 12 volt DC cordless, portable, rechargeable DC
power supplies, if extended operating time in the field is required.
FIGURE 2
NOZZLE HATCH COVER
NOZZLES
FIGURE 1
NOZZLE HATCH COVER
HOSE RETAINING RING
COMPRESSOR OUTLET
RIBBED BRASS FITTING
TRIGGER LOCK
TRIGGER SWITCH
PRESSURE GAUGE
COMPRESSOR HOSE
CAUTION:
TIRE CHUCK
This battery pack is delivered in a partially charged state - you must fully charge it
before using it for the first time. Initial AC charge should be for 10 hours. Refer to
Section 6 for use of AC adapter and detailed charging instructions.
3
4
VEC258 Manual 3/03.qxp 1/23/07 5:18 PM Page 5
The DC power adapter has a fused DC plug and connecting cord stored inside the DC
power adapter. To use the DC power adapter, first remove the DC plug from it’s
storage in the adapter. Deploy the cord from storage, and connect the DC power
adapter to the compressor. Make sure it snaps into position. Connect the DC plug to a
12 volt DC source. To remove the DC power adapter, press it’s release buttons and the
adapter will separate from the compressor. Put the DC plug and cord in the adapter
for storage after use.
3.
ATTACHING THE COMPRESSOR’S AIR HOSE
The air hose is supplied as a separate item from the compressor body. The hose has
a ribbed brass fitting at one end and a standard tire chuck at the other end. To use the
hose it must first be connected to the compressor outlet. Loosen the hose retaining ring
(counterclockwise), insert the hose fitting into the short, rubber sealing sleeve. Make
sure the hose fitting is inserted fully into the sleeve. Partially tighten (clockwise) the
hose-retaining ring and push the fitting in further. Do this two or three times until the
fitting is firmly attached and the ring is firmly tightened.
FIGURE 3
CONTACT
WARNING:
Improperly attached hoses or nozzles can fly out under compressor pressure. Make
sure the connections are tight.
WARNINGS:
FUSED DC PLUG
1. There is risk of dust or dirt projectiles being released if the compressor hose or
nozzles are not clean when the compressor is turned on.
2. Wearing protective goggles while operating this compressor can protect eyes from
flying particles of dust and dirt. Failure to follow instructions may cause property
damage, and/or personal injury.
RELEASE BUTTON
3. Keep out of reach of children.
4.
POWERING THE COMPRESSOR OR LAMP
5.
CHARGING/RECHARGING THE BATTERY PACK
The compressor can be powered either from a supplied battery pack or from a
supplied DC power adapter.
Lead-acid batteries require maintenance to maintain a full charge and to ensure good
battery life. All lead-acid batteries suffer from self-discharge over time, and more
rapidly when they are at higher temperatures. Therefore, these types of batteries need
periodic charging to replace energy lost through self-discharge. When the battery pack
is not in use, Vector recommends that the battery is recharged at least every 60 days.
4.1
POWERING FROM THE BATTERY PACK
The supplied battery pack powers the compressor or inflator for short duration,
cordless operation. The battery pack should be fully charged initially before use (see
paragraph 5 for charging instructions.)
All batteries must be recharged as soon as possible after each use. If a battery is allowed
to remain in a discharged state, battery life will be reduced.
To connect the charged battery pack to either the compressor or lamp, align the
battery pack so the battery release buttons snap onto the appropriate appliance. The
battery pack fits only one way to ensure correct polarity of the contacts. To remove the
battery pack, press the battery pack release buttons and the battery pack will
separate from the appliance.
NOTE: Recharging battery after each use will prolong battery life; frequent heavy
discharges between recharges will reduce battery life. Overcharging will reduce
battery life. Never charge for more than 24 hours.
The time required to fully recharge the battery pack depends on the charge status
of the battery after it’s use. If the battery is discharged from recent use, recharge the
battery for 8 hours.
4.2
DC POWER ADAPTER USE
The DC power adapter can power the compressor or lamp for longer operation from
an external 12 volt DC power source.
5.1
AC RECHARGE OF BATTERY PACK
AC recharge requires the use of the supplied AC/DC adapter. The AC adapter
must be powered from 110 volt AC, 60 Hz North American standard AC receptacles.
The battery pack must be removed from the compressor body to gain access to
the recharge port.
5
6
VEC258 Manual 3/03.qxp 1/23/07 5:18 PM Page 7
CONTACT
FIGURE 4
IMPORTANT:
Always leave the tire chuck thumb latch in the open position when storing unit.
RECHARGE PORT
RECHARGE LED
6.2
INFLATE OTHER ARTICLES (WITHOUT VALVE STEM)
Inflation of items, others than tires, requires use of one of the nozzles (adapters).
A nozzle can be attached to the tire chuck, or it can directly be connected to the
compressors outlet, if the hose is removed.
A nozzle can be attached to the tire chuck. Open the nozzle hatch cover and remove
the required nozzle. Close the nozzle hatch cover. Place the tire chuck over the nozzle
fitting and secure by moving the chuck thumb latch so it is parallel with the hose. Make
sure the nozzle is clean and secure before turning on the compressor. After use, release
the nozzle from the chuck by lifting the latch. Return the nozzle to the nozzle hatch.
RELEASE BUTTON
110 VOLT AC
WALL ADAPTER
WITH CORD
A nozzle can also be directly attached to the compressor outlet if the hose is not required.
1. Open the nozzle hatch cover and remove the required nozzle.
2. Remove the hose from the compressor outlet by loosening (counterclockwise) the
hose retaining ring and sliding out the ribbed brass fitting.
3. Close the nozzle hatch cover.
To remove the battery pack from the appliance body for charging: make sure the
trigger switch is OFF. Press both battery pack release buttons at the same time. Pull
the battery pack down away from the appliance body. Insert the barrel connector of
the AC adapter into the battery pack’s receptacle (recharge port). Plug the AC adapter
into a 110 volt AC standard household receptacle. Observe the red LED lights. Charge
for the recommended time. Do not overcharge! Disconnect and store the AC recharge
adapter from the battery pack and AC source when not in use.
4. Insert the selected nozzle into the compressor outlet and secure it by tightening the
hoseretaining ring as above.
5. After using the compressor, remove and store the nozzle in the nozzle hatch.
Refer to “Typical Inflation Times” for approximate pressure and time. Small items like
volleyballs, footballs, etc. inflate very rapidly.
6. Insert nozzle (e.g needle) into item to be inflated and inflate to desired pressure.
7. Turn on compressor switch - inflate to desired pressure or fullness.
6.
COMPRESSOR/TIRE INFLATOR
This 12 volt DC compressor is the ultimate compressor for all vehicles, trailer tires and
recreational inflatables. Three different sized nozzles are supplied.
7.
TYPICAL INFLATION TIMES FOR COMPRESSOR USE
IMPORTANT:
The following are approximate pressure and inflation times for various items:
Read safety instructions carefully to avoid possible injury or property damage.
WARNING:
WARNINGS:
Always follow tire manufacturers recommendations for pressure on item to be inflated.
The compressor is capable of inflating to 260 pounds per square inch (PSI) pressure
(approximately 18 kg/cm). To avoid over-inflation, carefully follow instructions on
articles to be inflated. Never exceed recommended pressures. Bursting articles can
cause serious injury. Always check pressure with the pressure gauge. Never leave
compressor unattended while in use. Allow unit to cool for five minutes after 10 minutes
of continuous operation.
VEHICLE AND TRAILER TIRES
TIRE SIZE
155/80R 13"
185/70R 14"
235/75R 15"
235/85R 16"
PRESSURE
26 psi
30 psi
30 psi
50 psi
TIME FROM “0” PRESSURE
2.50 min.
4.50 min.
6.50 min.
16.00 min.
6.1
TIRE INFLATION OR PRODUCTS WITH A VALVE STEM
BICYCLE TIRES
TIRE SIZE
1. Place connector (chuck) on valve stem.
PRESSURE
10 psi
TIME FROM “0” PRESSURE
40 sec.
2. Push connector toward valve stem and close thumb latch.
3. Make sure connector is pushed on to valve stem as far as possible before closing
thumb latch.
27 x 1" racing
INFLATABLE ARTICLES
ITEMS
4. Turn on the compressor (for larger items the trigger can be latched).
5. Observe pressure with the pressure gauge.
6. When desired pressure is reached, open thumb latch and remove connector from
valve stem.
PRESSURE
13 psi
9 psi
TIME FROM “0” PRESSURE
24 seconds
Football
Basketball
20 seconds
6 seconds
Volleyball
5 psi
7. Turn off compressor power switch
7
8
VEC258 Manual 3/03.qxp 1/23/07 5:18 PM Page 9
Approximate continuous runtimes on a fully charged battery are:
8.
LANTERN LIGHT
Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 hours
Fluorescent light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 hours
Emergency flasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 hours
Recharge the battery pack after each use. Refer to Section 5 for details.
The lantern light comprises three lights in one. The spotlight provides a bright focused
light. A bright long lasting fluorescent lamp provides general area lighting. A three-
position slide switch turns the fluorescent light on and off. This switch also turns a three-
LED emergency flasher on and off.
The main quartz-halogen spotlight is controlled on and off by a latching trigger switch
on the handle.
The lantern light is powered by either the 12 volt battery pack or the 12 volt DC power
adapter.
8.1
PARTS REPLACEMENT LANTERN LIGHT
Replaceable parts for the lantern light are:
The quartz halogen bulb; the fluorescent tube, and the battery pack.
FIGURE 6 - LANTERN LIGHT PARTS REPLACEMENT
A 12 volt DC accessory socket is located on the side of the unit. This permits cell phone
recharging or operating other 12 volt DC appliances. If the battery pack is installed
(3 Amp hour 12 volt battery or 36 watt hours), appliance wattage should be limited
to prevent rapid battery rundown.
BULB
REFLECTOR
FIGURE 5
BEZEL
LENS
SPOTLIGHT
SPOTLIGHT TRIGGER SWITCH
(LATCHING)
SCREW HOLE
(SCREW REMOVED)
SCREW
SLIDE SWITCH
FLUORESCENT/OFF/
EMERGENCY FLASHER
REMOVE LENS
EMERGENCY FLASHER
FLUORESCENT LAMP
12V DC
ACCESSORY SOCKET
8.2
QUARTZ HALOGEN BULB REPLACEMENT
The bulb is a 15 watt, 12 volt G4 projection type. This type bulb has two connector
pins that plug into a socket. The procedure follows:
1. Unscrew the bezel (counterclockwise) and remove the bezel and lens.
2. Hold the reflector in place against the body of the lamp and pull the bulb straight out.
Note the location of two socket holes that accept the bulb pins.
BATTERY PACK OR
DC POWER ADAPTER
3. Unpack the new bulb. Using a clean cloth, remove it from the packing material.
NOTE: Do not touch the new bulb with bare hands; oil from fingers can cause
premature failure of these bulbs. If the bulb is touched, clean the bulb with alcohol on
a clean cloth after the bulb is installed.
9
10
VEC258 Manual 3/03.qxp 1/23/07 5:18 PM Page 11
4. Push the pins the new bulb into the socket and make sure the bulb is fully inserted.
5. Replace the lens and bezel.
11.
BATTERY DISPOSAL
6. Tighten (clockwise) the bezel until it is snug.
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be
disposed of properly. Most states require recycling-contact your local municipal
authority for information.
7. Test the light for proper operation by turning it ON and then OFF.
8.3
FLUORESCENT LAMP REPLACEMENT
Non-spillable, sealed, lead-acid battery, must be recycled or disposed of properly.
Recycling is required - contact your local authority for information. DISPOSAL
QUESTIONS FOR USA CALL toll free (877)288-7722.
The bulb type is a standard 4 watt F4T5/D fluorescent tube type. A replacement bulb
can be purchased from local lighting, hardware or camping stores. The fluorescent lamp
tube can be replaced after the front vertical lens is removed. The procedure follows:
WARNINGS:
1. Remove the battery pack or DC adapter. Using a small Phillips screwdriver,
unscrew (counterclockwise) the small screw at the top of the lens.
2. Slide the lens down from the top of the unit. The lens will come off. Set the lens aside.
3. Remove the fluorescent tube by turning one-quarter turn so pins at both ends of
the tube are released from the sockets. The tube will come out.
4. Set the defective tube aside for proper disposal.
5. Put in a new tube, being careful to keep the bulb pins from bending.
6. Rotate the tube one-quarter turn to lock the pins into the sockets.
7. Check the new tube to make sure it is secure in the sockets.
8. Replace the lens, and slide it towards the top of the unit. The screw holes should
align.
9. Replace the small screw and carefully tighten with the Phillips screwdriver.
10. Follow local ordinances for fluorescent bulb disposal and discard the old bulb.
• Do not dispose of the battery pack in fire as this may result in an explosion.
• Before disposing of the battery pack, protect exposed terminals with heavy-duty
electrical tape to prevent shorting (shorting can result in injury or fire). Failure to
comply with local, state and federal regulations can result in fines, or imprisonment.
12.
SPECIFICATIONS
FOR COMPRESSOR:
Battery . . . . . . . . . . .12 volt, 3 Amp Hour, Non-spillable Sealed Lead-Acid
Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260 PSI Maximum
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.82 lbs (.90 kg)
Height w/battery . . . . . . . . . . . . . . . . . . . . . . . . .11.25 inches (28.57 cm)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.0 inches (10.16 cm)
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 inches (17.78 cm)
9.
MAINTENANCE/REPLACEMENT PARTS
LANTERN LIGHT:
For replacement parts (batteries, DC power adapters, AC charging adapters, cables,
etc.), contact Vector technical support: (954) 584-4446 or toll free at (866) 584-5504.
Periodically, cables, hose, nozzles, and connectors should be inspected for damage,
corrosion, dust; and dirt. If surfaces are dirty, they can be wiped clean with a cloth
moistened with water and a drop of detergent. Battery pack contacts can be wiped
clean with a dry cloth.
Quartz Halogen Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15W, G4
Fluorescent Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F4T5/D
10.
BATTERY REPLACEMENT
The battery in the battery pack should be replaced with a new one when the operating
capacity is reduced to about one half or the ability to inflate one and one half
average sized automobile tires. Make sure that the battery is fully charged before
determining that the battery pack should be replaced. Contact Vector technical
support and ask for part VEC194. This battery pack is also used with other Vector
products that include portable inflators and spotlights. For more details, please contact
our technical support department toll free at (866) 584-5504.
11
12
|