User's Manual
TM
Talk & Go Farm Rattle
© 2011 VTech
Printed in China
美
91-002534-005
INTRODUCTION
TM
Thank you for purchasing the VTech® Talk & Go Farm Rattle learning
toy!
Peek-a-boo! I see you baby animals! With the VTech® Talk & Go
TM
Farm Rattle, you will hear fun phrases and play peek-a-boo to learn
about mommy and baby animals. Move the dangling baby animal
pieces or press the mommy animal buttons to hear animal sounds
and fun phrases. The motion sensor activates a variety of farm
themed melodies and animal sounds. It’s another day of fun down
on the farm!
ON/OFF/VOLUME
CONTROL SWITCH
LIGHT-UP MUSIC NOTE
ANIMAL BUTTONS
DANGLING ANIMAL PIECES
2
INCLUDED IN THIS PACKAGE
TM
- One VTech® Talk & Go Farm Rattle
- One instruction manual
WARNING: All packing materials, such as tape, plastic sheets,
packaging locks and tags are not part of this toy, and
should be discarded for your child’s safety.
ATTENTION: Pour la sécurité de votre enfant, débarrassez-vous
de tous les produits d’emballage tels que rubans
adhésifs, feuilles de plastique, attaches et étiquettes.
Ils ne font pas partie du jouet.
NOTE:
Please keep this instruction manual as it contains
important information.
Unlock the packaging locks:
Rotate the packaging lock 90
degrees counter-clockwise
Pull out the packaging lock
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the back of
the unit. Use a screwdriver to loosen the
screw.
3. Install 2 new ‘AAA’ (AM-4/LR03) batteries
following the diagram inside the battery box.
4. Replace the battery cover and tighten the
screw to secure .
3
BATTERY NOTICE
•
The use of new alkaline batteries is recommended for maximum
performance.
•
•
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the toy before
being charged (if removable).
•
•
•
Rechargeable batteries are only to be charged under adult
supervision (if removable).
Different types of batteries or new and used batteries are not to
be mixed.
Only batteries of the same or equivalent type as Instructions &
Activitiesare to be used.
•
•
•
•
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the toy.
The supply terminals are not to be short-circuited.
The toy is not to be connected to more than the recommended
number of power supplies.
•
Do not dispose of batteries in fire.
PRODUCT FEATURES
1. ON/OFF/VOLUME CONTROL SWITCH
To turn the unit ON, slide the ON/OFF/
VOLUME CONTROL SWITCH to the LOW
VOLUME [
] position or to the HIGH
VOLUME [
] position.To turn the unit OFF,
slide the ON/OFF/VOLUME CONTROL
SWITCH to the OFF [ ] position.
2. AUTOMATIC SHUT-OFF
TM
To preserve battery life, the VTech® Talk & Go Farm Rattle will
automatically power-down after approximately 30 seconds without
input. The unit can be turned on again by pressing any of the buttons
or dangling animal pieces. Please note, activating the motion sensor
will not turn the unit back on.
4
ACTIVITIES
1. Slide the on/off/volume control switch
to turn the unit on. You will hear an
encouraging phrase and animal sounds
followed by a sing-along song. The light
will flash with the sound.
2. Press one of the animal buttons to hear
short tunes, animal sounds, melodies and
fun phrases. The light will flash with the
sound.
3. Flip the dangling animal pieces to learn
colors, animal names and sounds and hear
playful phrases and short tunes. The light
will flash with the sound.
4. Shake the rattle to activate the motion
sensor and hear a variety of melodies and
a sing-along song. The light will flash with
the sound.
MELODY LIST
1. Farmer in the Dell
2. Happy Farmer
3. Old MacDonald Had a Farm
4. Animal Fair
5. The Bear Went Over the Mountain
6. Little Miss Muffet
5
SING-ALONG SONG LYRICS
The animals are playing peek-a-boo,
Come along, join the fun!
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct
heat source.
3. Remove the batteries when the unit is not in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
TROUBLESHOOTING
If for some reason the program/activity stops working or malfunctions,
please follow these steps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. If the product still does not work, replace with an entire new set
of batteries.
If the problem persists, please call our Consumer Services Department
at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, and a
service representative will be happy to help you.
For information on this product’s warranty, please call VTech® at
1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada.
6
IMPORTANT NOTE:
Creating and developing Infant Learning products is accompanied
by a responsibility that we at VTech ® take very seriously. We make
every effort to ensure the accuracy of the information, which forms
the value of our products. However, errors sometimes can occur.
It is important for you to know that we stand behind our products
and encourage you to call our Consumer Services Department at
1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, with
any problems and/or suggestions that you might have. A service
representative will be happy to help you.
Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Caution: changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
7
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OP-
ERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OP-
ERATION.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À
LA NORME NMB-003 DU CANADA.
8
|