STEP1 Press the [CBL] button and the
[SELECT] button simultaneously
for 3 seconds.
STEP3 Press the [DEVICE] button and the
[POWER] button you wish to store in
the [SYSTEM ON/OFF] button and
repeat this until you stored all the
power commands into the [SYSTEM
ON/OFF] button.
STEP4 Press the [CH+] button to save the
power commands you stored. The
[CBL] button will blink twice to
confirm the saving.
C. To Find the Three Digit Code Number
That was Stored in the Device.
STEP1 Press the [DEVICE] button (TV, VCR ,
DVD or AUX) you wish to verify and
the [SELECT] button simultaneously
for 3 seconds. The device LED will
turn on.
*Tip : The equipment will turn off when the
correct three-digit code number has
been entered. You can verify you have
selected the correct code by pressing
the [POWER] button, the equipment
should turn on or turn off.
Introduction
Button Functions
3
1
Operating Instructions
For The UR5-8400
The remote control is designed to operate
the Scientific Atlanta Explorer 8000, Pioneer
Voyager DVR and the Pace Micro DVR
Series. You can also control the majority of
TV, VCR, DVD and AUDIO equipment on the
market as shown below.
The [CBL] device LED will turn on.
*Tip :The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
Cable Remote Control
*Note : If there is more than one three-digit
number listed for your brand, try one
code number at a time until your
equipment turns off.
STEP2 Press the [VOL +] button.
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
CABLE : Cable Converters
VCR : VCRs and TV/VCRs
AUX : Audio Receivers, etc.
TV : Televisions
UR5-8400
DVD : DVD Players
STEP3 Press the [CBL] button.
The device LED will blink twice to
confirm the programming.
STEP4 Store the three-digit code number
by pressing the same [DEVICE]
button once again. The device LED
will blink twice to confirm that the
code has been stored.
F. Programming Channel Control.
STEP2 Press the [INFO] button.
Replacing Batteries
2
To return to original state:
By following the steps below, the user can
program the channel controls (Channel Up,
Channel Down and Last) from one device to
operate in another device mode. The default
channel control settings on the remote
control are as follows:
The device LED will blink number of times
indicating the number of each digit of the
code number. Each digit is separated by a 1
second interval of the LED being turned off.
If you wish to restore the TV volume
control in CBL mode, repeat the above
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
steps by pressing [TV] in STEP3
.
STEP1 Remove the battery compartment cover
*Note : Try all the functions on the remote
control. If any of the functions do not
work as they should, repeat from
Step 2 using the next three-digit code
number from the same brand list.
on the back of your remote control.
Example : One blink, three blinks and eight
blinks with an interval of 1 second
of LED being turned off, indicates
the code number 138.
STEP2 Check battery polarity carefully, and
install the batteries as shown In the
illustration below.
H. Programming For Advanced Function.
CBL : CBL
VCR : CBL
AUX : AUX
T V : CBL
DVD : DVD
In the CBL mode, the BLANK button can be
programmed to act as a macro or favorite
channel button. You can send out up to ten
commands with one button press.
STEP3 Replace the battery compartment cover.
Note : Ten blinks is equal to the number 0.
If you wish to store the TV channel control in
TV mode, use the following steps.
B. Auto Search Method.
D. Programming a second TV to AUX Mode.
STEP1 Press the [CBL] button to select
If the three-digit code numbers assigned to
your brand do not turn off your equipment or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by the following steps:
the CBL mode.
STEP1 Press the [AUX] button to be
programmed and the [SELECT] button
simultaneously for 3 seconds.The
[AUX] device LED will turn on.
STEP1 Press the [TV] button and the
[SELECT] button simultaneously for
3 seconds.
STEP2 Press the BLANK button and
[SELECT] button simultaneously
for 3 seconds. The [CBL] device
LED will turn on for 20 seconds.
STEP3 Press up to 10 buttons you wish to
store. The [CBL] device LED will blink
once for each command entered.
STEP4 Press the [CH+] button to store the
functions that were selected. The
[CBL] device LED will blink twice to
confirm the storage of functions.
The [TV] device LED will turn on.
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
*Tip :The device LED will light on for 20
seconds. The next step must be
entered while the LED is on.
STEP1 Turn on the equipment you wish to
operate.
STEP2 Press the [TV] device button to pick
STEP2 Press the [VOL -] button.
STEP2 Press the [DEVICE] button (TV, VCR,
DVD or AUX) to be programmed and
the [SELECT] button simultaneously
for 3 seconds. The device LED will
turn on.
up the TV code table.
STEP3 Press the [TV] button.
The device LED will blink twice to
confirm the programming.
STEP3 Point the remote control toward the
equipment and enter the three-digit
code number assigned to your TV
brand from the code tables.
STEP4 Store the three-digit code number by
pressing the [AUX] button once
again. The device LED will blink
twice to confirm that the code has
been stored.
I. Low Battery Warning.
To return to original state:
When the batteries are low and need to be
replaced with fresh batteries, the remote
control LED will blink 2 times in sequence
whenever a [POWER] button is pressed to
turn on equipment.
If you wish to restore the CABLE channel
*Tip : The device LED will turn on for 20
seconds. The next step must be
entered while LED is on.
Operations
4
control in TV mode, repeat the above steps
Programming the Remote Control
5
by pressing [CBL] in STEP3
.
Default State:
Device Default: CABLE
STEP3 Press the [CH+] or [CH-] button one
at a time or keep it pressed. The
remote will emit a series of power
on/off commands. Release the
[CH+] or [CH-] button as soon as the
equipment turns off.
*Tip : You can verify that you selected the
correct code by pressing the [POWER]
button. The equipment should either
turn on or turn off.
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit
code numbers are listed in the code table of the instruction manual.
Volume Default: You have the option of controlling
your TV volume and mute through the Cable box,
VCR or DVD. Refer to section G for programming the
volume and mute through your Cable box, VCR or
DVD.
G. Programming Volume Control.
J. Memory Lock System.
By following the steps below, the user can
program the volume controls (Volume Up,
Volume Down and Mute) from one device to
operate in another device mode. The default
volume control settings on the remote
control are as follows:
This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control.
E. Programming the System On/Off Button.
This is designed to program the System On/Off
button so that it can send out up to five power
on/off commands with one button press.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)
Channel Default: You have the option of controlling
your CABLE channel and number keys through the
TV or VCR. Refer to section F for programming the
channel and number keys through your TV or VCR.
STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [SELECT]
button simultaneously for 3 seconds. The device LED will turn on indicating the unit is
ready to be programmed.
K.Write your device Set-up codes.
STEP1 Press the [CBL] button.
TV
Set-up Code Number:
CBL : TV
VCR : TV
AUX : AUX
T V : TV
DVD : TV
STEP2 Press the [SYSTEM ON/OFF] button
and the [SELECT] button
System On/Off button:
VCR Set-up Code Number:
DVD Set-up Code Number:
AUX Set-up Code Number:
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED
This button is designed to send out power
commands for two, three, four or all five devices with
one button press. Please refer to section E for
details.
Universal Remote Control, Inc.
STEP4 Press the same [DEVICE] button to
store the code. The device LED will
blink twice to confirm that the code
has been stored.
is on.
simultaneously for 3 seconds. The
[CBL] button will turn on for 20
seconds.
STEP3 Point the remote control toward the equipment and enter the three-digit code number
OCE-0017D Rev 03 (11/29/05)
If you wish to store the CBL volume control in
CBL mode, use the following steps.
assigned to your brand from the code tables.
|