*Tip : The equipment will turn off when
the correct three-digit code
number has been entered. You
can verify you have selected the
correct code by pressing the
[MUTE] button, the equipment
should turn on or turn off.
STEP3 Press the [CH+] or [CH-] button
one step at a time or keep it
pressed. The remote will emit
a series of Power ON/OFF
commands. Release the [CH+]
or [CH-] button as soon as the
equipment turns off.
STEP3 Press the [DEVICE] button
you wish to store in the
[SYSTEM ON/OFF] button
and repeat this until you
stored all the power
D. Programming a second TV
to VCR Mode.
G. Programming For
Advanced Function.
Introduction
Button Functions
3
1
Operating Instructions
For 4 Function
DTV Remote Control
The remote control is designed to
operate the DTV series set top boxes
and the majority of TV, VCR/DVD and
AUDIO equipment on the market.
In the CABLE mode, the [ ] button can
STEP1 Turn on the TV you wish to
*
be programmed to act as a macro or
program.
favorite channel button to send out up
to 10 commands with one button press.
commands
into
the
STEP2 Press the [VCR] button to be
programmed and the [SELECT]
button simultaneously for 3
seconds. The [VCR] device
LED will turn on.
[SYSTEM ON/OFF] button.
STEP1 Press the [CBL] button to
*Note : If there is more than one
three-digit number listed for your
brand, try one code number at a time
until your equipment turns off.
STEP4 Press the [CH+] button to save
the power commands you
stored. The [CBL] device LED
will blink twice to confirm the
saving.
*Tip : You can verify that you selected
the correct code by pressing the
[MUTE] button. The TV should
either turn on or turn off.
Replacing Batteries
Before you program or operate the
remote control, you must install two
new AA alkaline batteries.
2
select the CABLE mode.
STEP2 Press the [ ] button and
*
*Tip : The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
[SELECT] button simultaneously
for 3 seconds. The [CBL] device
LED will turn on for 20 seconds.
STEP4 Store the three-digit code
number by pressing the same
[DEVICE] button once again.
The device LED will blink
twice to confirm that the
code has been stored.
STEP4 Press the same [DEVICE]
button to store the code. The
Device LED will blink twice to
confirm that the code has
been stored.
STEP1 Remove the battery compartment cover
F. Program the Volume
Controls.
By following the steps below, you
can program the volume controls
(Volume UP, Volume Down and
MUTE) to your TV, VCR and Audio.
STEP3 Press the [TV] button to
STEP3 Press up to 10 buttons you
wish to store. The [CBL] button
LED will blink once for each
command entered.
on the back of your remote control.
access the TV code table.
STEP2 Check battery polarity carefully,
and install the batteries as shown
in the illustration below.
STEP4 Point the remote control
toward the equipment and
enter the three-digit code
number assigned to your TV
brand from the code tables.
*Tip : You can verify that you selected
the correct code by pressing the
[MUTE] button. The equipment
should either turn on or turn off.
STEP4 Press the [CH+] button to store
the functions that are selected.
The [CBL] device LED will blink
twice to confirm the storage of
functions.
*Note : Try all the functions on the
remote control. If any of the functions
do not work as they should, repeat from
Step 2 using the next three-digit code
number from the same brand list. Make
sure that the VCR/VOD button is in the
VCR position when using your VCR.
STEP3 Replace the battery compartment cover.
C. To Find the Three Digit
Code Number That was
Stored in the Device.
STEP1 Press the [DEVICE] button (TV,
VCR or AUD) you wish to verify
and the [SELECT] button
simultaneously for 3 second.
The device LED will turn on.
The default volume control settings
on the remote control is TV volume
control. If you wish you can control
the volume via your cable box or
audio equipment. Use the following
steps to change the volume control H. Low Battery Warning.
STEP5 Store the three-digit code
number by pressing the [VCR]
button once again. The [VCR]
device LED will blink twice to
confirm that the code has
been stored.
settings:
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh
batteries, device LED will blink 2 times
in sequence whenever a [DEVICE]
button is pressed to turn on equipment.
STEP1 Press the [CBL] button and
the [SELECT] button
B. Auto Search Method.
If the three-digit code numbers assigned
to your brand do not turn off your
equipment or the code tables do not list
your brand, you can use the Auto Search
Method to find the correct three-digit
code number for your equipment by the
following steps:
simultaneously for 3 seconds.
The [CBL] device LED will
turn on.
*Tip : The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
Programming the Remote Control
5
*Tip : The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
E. Programming the
System On/Off Button.
This button is pre-programmed to turn on
all devices with one button press,
however you can also program to turn on
one or two devices by following these
steps:
I. Memory Lock System.
A. Programming For Your Devices.
Operations
Default State :
4
STEP2 Press the [INFO] button.
This remote control is designed to
retain programmed memory for 10
years even after batteries are removed
from the remote control.
The remote control can be programmed by pressing in a three digit code number
that corresponds to particular manufacturers and brands of Audio/Video
equipment. The three-digit code numbers are listed in the code table of the
instruction manual.
The device LED will blink number of
times indicating the number of each
digit of the code number. Each digit is
separated by a 1 second pause of the
LED being turned off.
Device Default: DTV Cable box.
Volume Default: TV volume and mute
through the TV, with the option of
controlling volume and mute through
the Cable box or Audio. Refer to Section
F for programming the volume and mute
through your Cable box or Audio.
STEP2 Press the [ VOL + ] button.
STEP1 Turn on the equipment you
STEP3 Press the [ CBL ], [ AUD ]
(whichever applicable) button.
The [CBL] device LED will
blink twice to confirm the
programming.
wish to operate.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUDIO).
STEP2 Press the [DEVICE] button (TV,
VCR or AUD) to be programmed
and the [SELECT] button
simultaneously for 3 seconds.
The device LED will turn on.
J. Write your device Set-up codes.
STEP2 Press the [DEVICE] button (TV , VCR or AUD) to be programmed and the
[SELECT] button simultaneously for 3 seconds. The device LED will turn
on indicating the unit is ready to be programmed.
TV
Set-up Code Number :
STEP1 Press the [CBL] button.
Example : One blink, three blinks and
eight blinks with an interval of 1 second
of LED being turned off, indicates the
code number 138.
VCR Set-up Code Number :
AUDIO Set-up Code Number :
STEP2 Press the [SYSTEM ON/OFF]
button and the [SELECT]
button simultaneously for 3
seconds. The [CBL] device
LED will turn on for 20
seconds.
System On/Off button:
To return to original state:
*Tip : The device LED will light on for 20 seconds. The next step must be entered
This button is designed to send out
power commands for two, three or all
four devices with one button press.
Please refer to section E for details.
If you wish to restore the TV volume
control in CABLE mode, repeat the
above steps by pressing [ TV ] button in
while the LED is on.
Universal Remote Control, Inc.
*Tip : The device LED will light on for
20 seconds. The next step must
be entered while the LED is on.
OCE-0002A Rev 12(05/31/07)
STEP3 Point the remote control toward the equipment and enter the three-digit
Note : Ten blinks is equal to the
number 0.
code number assigned to your brand from the code tables.
|