®
LRD 6699SWS
Operating Guide
CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Feature Highlights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Speed Detection Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Radar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Included with Your Radar Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LED Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Helpful Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting the Windshield Mounting Clip. . . . . . . . . . . . . . . . . . . 10
Connecting the Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Replacing the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Full Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
The Safety Warning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Memory Retention Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Audio/Dimmer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Mute Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
City/Highway Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LED Signal Strength Meter in City Mode . . . . . . . . . . . . . . . . . . 18
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SWS Warning Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Highway Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Highway Hazard Zone Advisory . . . . . . . . . . . . . . . . . . . . . . . . . 23
Weather Related Hazard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Travel Information Convenience . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fast/Slow Moving Vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Features, Specifications, and availability of Optional Accessories are all
subject to change without notice.
Uniden® is a registered trademark of Uniden America Corporation.
Introduction
Welcome to the world of sophisticated, early warning laser/radar
detection. You have purchased one of the most advanced laser/radar
detectors available. The LRD 6699SWS is a complete integrated
laser/radar detector. It responds to the X-, K-, and Ka-SuperWideband
radar guns in use today and also provides 360° detection of the latest
speed monitoring system — the laser gun. And, the built-in Safety
Warning System (SWS™) is capable of detecting hazardous warning
signals transmitted on the K-band.
The LRD 6699SWS provides distinct visual and audio alerts to warn you
of the presence of X-, K-, and Ka-SuperWideband radar signals as well as
IR laser signals. You can drive with confidence when you bring along the
LRD 6699SWS.
The LRD 6699SWS employs Super Stalker Technology (SST), a
state-of-the-art electronic system designed to make this radar detector
invisible to all current VG-2 radar detector detectors. The LRD 6699SWS
also uses the new D.R.O. (Dielectric Resonant Oscillator) and E.D.I.T.
(Electronic Data Interference Terminator) circuitry, giving more reliable
performance.
We are certain that you will enjoy the LRD 6699SWS, and to ensure that
you get the most from its features, please read this Operating Guide
carefully before installing and operating the unit.
Feature Highlights
• Safety Warning System™ with • 360° Laser Detection
8-digit message display
• Complete Four-Band Coverage • Super Wideband
• VG-2 Undetectable
• K/Ka Priority
• Audio/Dimmer Mode
• Auto Mute Mode
• Self Test
• Pulse Detection
• Signal Strength Meter
• City and Highway Modes
• Memory Retention Feature
• 5 Alert tones
1
Speed Detection Systems
A speed detection device (often called a radar gun) sends out either a
microwave signal or beam of light. When this signal reaches its target,
part of the signal is reflected or bounced back toward the emitting gun.
The time required for the signal to leave the gun, bounce off an object,
and return is used to determine a vehicle’s distance and speed.
Radar
Radar (Radio Detection and Ranging) is a microwave system for
detecting the speed of moving objects by reflected pulses of high
frequency radio waves. There are three radar bands (microwave
frequencies): X-band (10.49 to 10.56GHz), K-band (24.04 to 24.26 GHz),
and the “SuperWide" Ka-band (33.4 GHz to 36 GHz).
The X-band was the first used for traffic, followed by the K-band which
is harder to detect (most instant-on radar is K-band). The Ka-band was
introduced in 1987, and widened to Ka-SuperWideband in 1990 by the
FCC. The LRD 6699SWS monitors all current radar bands including the
entire Ka-SuperWideband.
The radar beam is cone shaped — the narrower the beam, the greater the
resolution. A moving vehicle reflects radar signals back towards the radar
gun. The LRD 6699SWS can detect the signals emitted by radar guns,
and it will sound an audio alarm and flash a warning indicator.
For continuously transmitting radar, use the LRD 6699SWS to get
accurate detection from a safe distance. Weak signals cause the audio and
visual alarms to sound intermittently, but as the signal gets stronger (the
closer you get to the radar gun), both alarms increase in intensity.
Instant-on transmitters fire a short radar pulse beam at a vehicle and
instantly read its speed. When detected at a distance, you will hear a few
beeps and see the strength meter begin to light. Instant-On radar signals
are the most difficult to detect at a safe distance because they are
transmitted only when directed at you or at a vehicle directly ahead of
you.
2
Laser
The Laser Speed Detection System, also called LIDAR (for Light
Detection and Ranging), uses a laser gun that emits infrared light pulses
just outside the spectrum of visible light. Each reflected pulse measures
the speed of the object coming toward, or going away from, the laser gun.
Unlike radar, the laser gun emits a very narrow beam of light, so it can
pinpoint a speeding car within traffic. The infrared beam spreads out, but
slowly and over a longer distance than a radar signal.
The laser gun can acquire a speed reading as quickly as 0.3 seconds,
sometimes less. However, since it isn’t easy to accurately aim at and hit a
moving target, an operator often moves the laser gun in several directions
to get a reading. So laser signals are emitted continuously for a few
seconds for each speed measurement. The LRD 6699SWS can detect
these light pulses from as far away as 1.5 miles, which is about four times
the effective range of a laser gun (2,000 feet), and about ten times its
average operating range (500-800 feet).
Note: To be safe, do not ignore any warnings. Although there are other
types of radar signals that may cause interference, when the
LRD 6699SWS detects a signal, be on the alert. It is important to
exercise caution at all times.
3
Included with Your Radar Detector
Windshield Mounting
Owner’s Guide
Clip
Printed Material
Fuses and Spare Parts
Coiled Cigarette
Adapter
Straight Power Cord
If any of these items are missing or damaged, contact Uniden Parts
Department at (800) 554-3988, 8 a.m. to 5 p.m., Central, Monday through
Friday. Be sure to complete and mail the Product Registration Card.
4
Controls and Functions
2
1
2
3
4
5
6
9
8
7
1.
2.
3.
Clip Release — Press the clip release button to remove the LRD
6699SWS from the windshield mounting clip.
Rear, Side, and Front Laser Detector Lenses — For rear, side, and
front detection of laser signals.
CITY Button — With each press, the mode toggles from Highway
to City mode. The CITY button helps reduce X-band false alarms
while driving in the city. Select HIGHWAY for long range
detection. Depending on the mode selected, either CTY or HWY
will display in the LED Display.
4.
5.
AUDIO Button — With each press, the mode toggles from
DIMMER (LEDs dim only), to AUDIO (turns off LED display
except mode indication and dims the Three-Color LED), to
NORMAL (LED display and audio on).
Speaker — Sounds audio alert. There are five different alert tones
to distinguish each type of signal received. When you become
familiar with all the distinct alert tones, you can operate the
LRD 6699SWS just by listening, devoting your full attention
to driving.
6.
MUTE Button — Press the MUTE button to activate the Auto
Mute feature, which produces a full alert tone when a signal is first
received, then automatically reduces to half volume. If activated in
City mode, an alert sounds briefly, followed by a Mute tone (see
page 18).
5
7.
LED Display — LEDs display LASER/RADAR alerts, signal
strength, operation mode, and Safety Warning System (SWS)
messages.
8.
9.
On-Off/Volume Control — Turns the power on (with a click) and
adjusts the Audio alert volume.
12V DC Power Input — Connect the DC power cord here.
®
Note: Use only a Uniden supplied power cord or its replacement.
6
LED Displays
3
1
2
4
5
6
1.
2.
Three-Color LED — Red indicates a radar detection; Green
indicates a laser detection; and Amber indicates a Safety Warning
System(SWS) message.
Band and City/Highway Mode — The first three LEDs indicate
X-, K-, Ka-SuperWideband radar signal, and City or Highway
mode. If a laser signal is detected, LASER will display in the first
five LEDs while the remaining LEDs light. A distinct audio alert
is heard for radar and laser signals.
3.
4.
LED Signal Strength Meter — Starting with the third LED
position, as the signal gets stronger, additional LEDs will light.
See page 18, LED Signal Strength Meter in City Mode.
Safety Warning System (SWS) Display — All eight LEDs display
SWS messages. Messages longer than eight-digits are scrolled
repeatedly. When SWS data is received and cannot be specified,
‘SAFETY WARNING MESSAGE’ displays. A distinct audio
alert is heard for SWS messages.
5.
6.
Dimmer/Audio Mode — The fifth LED position indicates Dimmer
(D) or Audio (A) mode. Dimmer mode dims the LEDs but
displays all possible data. Audio mode disables signal displays and
dims the Three-Color LED.
Mute Mode — The seventh LED position indicates Mute (M)
mode. Signals received sound for a few seconds then are reduced
to half the normal tone (Mute tone).
7
When a Ka-band is received with a signal strength of 4:
Ka
Red
When City, Audio, and Mute modes are turned on:
C Y A
T
M
When a SWS message ‘ROAD CLOSED AHEAD’ is received:
R O A D CL O
Amber
1. The first eight characters display for about two seconds.
2. The message scrolls to the left at the rate of approximately three
characters each second.
3. Scrolling stops at the end of the message and the display turns off
for one second.
4. The message displays again and repeats scrolling.
Note: Every time you turn on the LRD 6699SWS, a self-test is
performed for all LEDs and Alert tones. You will hear in-order
five distinct tones for the X-, K-, and Ka-SuperWideband radar
bands, Laser, as well as for SWS.
8
Installation
The LRD 6699SWS uses a highly sensitive horn-type antenna and IR
laser sensor to receive radar/laser signals. Its sensitivity and range depend
on the method of installation and the direction of the antenna/sensor in
relation to the signal source. The inherent nature of radar waves makes
them reflect off metallic surfaces. This is why these waves are so useful
for measuring the speed of a vehicle. The IR laser light may reflect only
from shiny surfaces. Both radar waves and IR laser light will, however,
pass through plastic or glass.
Before you decide where to put your radar detector, please keep in mind
these two important factors:
• For safety, do not mount the LRD 6699SWS in a location where it
will obstruct your driving vision.
• Most vehicles have the top part of the windshield tinted. Mounting
the LRD 6699SWS behind tinted or mirrored glass may reduce the
effectiveness of laser detection by reducing the amount of laser light
received by the Detector.
Helpful Tips
The antenna and the forward looking sensor
are located behind the rear panel of the unit,
(and the rear- and side-looking sensors are
located on top of the unit), directly behind the
mode selection keys. The antenna and
sensors should not be obstructed by metal or
metallic surfaces and should be pointed at the
horizon for accurate long-range detection.
• Do not mount the unit behind the windshield wiper blades, radio
antenna, tinted glass area, or mirrored glass. Be sure the unit is free
from obstruction by seat backs, rear view mirror, sun visors, or the
ceiling of the automobile.
• Do not mount the unit in front of the heater or defroster vents.
• Do not leave the unit in direct sunlight or in the glove compartment of
a closed car for long periods of time, as extreme changes in
temperature may cause internal damage. Also, removing the unit from
the windshield makes you less susceptible to break-in and theft.
9
Adjusting the Windshield Mounting Clip
1.
2.
The metal portion of the bracket locks into the plastic portion at
three different positions. These positions can be used for vehicles
with different vertical windshield angles. The back position can be
used for vehicles with windshields that are slanted back.
For optimum laser detection, bend the angled portion of the
windshield mounting bracket so that the LRD 6699SWS is parallel
to the road surface. Be sure the LRD 6699SWS is mounted so it is
free of obstructions from seat backs, rear view mirror, sun visors,
or the ceiling of the automobile. There must be a clear 360° line of
sight to the outside of the vehicle.
To mount the LRD 6699SWS:
1.
2.
Insert the windshield clip into the LRD 6699SWS.
Place the bracket and the LRD 6699SWS in the proper location on
the windshield of your vehicle, and press the suction cups firmly
against the windshield.
10
Connecting the Power
Warning: The LRD 6699SWS is designed to operate only with
12V DC, negative ground power systems. Operation of
the unit on other voltages or polarities will cause damage
to the unit and may create a fire hazard.
1.
Insert the small connector into the jack on the side of the unit.
2.
Insert the other end into the cigarette lighter socket of
your vehicle.
When installing the power cord, make sure that:
• The socket is clean to allow proper contact.
• The power cord does not block the antenna area on the back of the
unit.
Your unit also comes with ten power cord mounting clips. You can use
these clips to attach the power cord to the window frame or other parts of
the vehicle, keeping it neat and out of the way. Use the double-sided
foam tape squares to attach each clip. Slip the power cord into the clip to
hold it securely in place.
11
Replacing the Fuse
The cigarette lighter plug contains a 1-ampere fuse to protect it from
power surges.
1.
To replace the fuse,
unscrew the top of the plug.
2.
3.
Remove the fuse and
replace it with the same
type.
To replace the top, push in
the two metal contacts and
twist into place.
Note: Your LRD 6699SWS comes with an extra fuse.
12
Operation
You are now ready to enjoy the convenience and security of your
LRD 6699SWS. Please read this section of the Operating Guide carefully
to familiarize yourself with the basic operation of this unit.
Power On
Turn the Volume Control switch to turn power on. Once the Power-On
alert sounds, your LRD 6699SWS performs a six second self-test of all
circuits. The X-band alert sounds for two seconds while the Three-Color
LED illuminates red, and the Signal Meter LED lights. Next you will
hear the K-band, Ka-Super Wideband, Laser, and SWS alerts for one
second each. (The corresponding Three-Color LED, City/Highway,
Audio/Dimmer, and Mute indications also light.)
After the self-test, your detector sets the modes which were used last. If
this is the first time you have used your LRD 6699SWS, it should be set
for HWY use, and both the AUDIO and MUTE modes should be off.
If you experience any of these problems:
• Settings do not display
• The unit turns on and off intermittently
• An alert sounds too often for no reason
Check to make sure both ends of the power cord are tightly secured. If the
problems continue, refer to page 20, “Troubleshooting” for more
information.
Volume Control
Adjust the Volume to a
comfortable announcement/
alarm tone level for your
vehicle. The volume level
does not have any effect on
the unit’s sensitivity.
13
Full Warning
When the LRD 6699SWS detects a radar, laser, or safety warning signal,
it emits a distinct warning tone. The corresponding X-, K-, Ka-Super
Wideband, Laser, or SWS indication display along with the
corresponding red, green or amber Three-Color LED. For radar, as the
signal gets stronger, more signal strength LEDs light.
Note: The alert tones for the radar, laser, and SWS are all different.
The Safety Warning System
The Uniden Safety Warning System™ (SWS) is a new communication
system which will provide you with an early warning message when a
road hazard exists. The LRD 6699SWS is capable of detecting SWS
signal broadcasts on the K-band by either law enforcement or local
departments of transportation.
You will receive several indications when an SWS warning is received.
The three-color LED on the left part of the display turns amber, an alert
sounds, and a message appears on the 8-digit screen.
Since some warning messages exceed the screen’s display length, your
detector is designed to scroll messages with more than 8 characters. Also,
during an alert, certain conditions can cause warning indications to be
different from those you’ll usually get. These special indications are
listed below:
• If your detector receives a message but cannot determine its content,
the message “SAFETY WARNING MESSAGE” is displayed.
• Similarly, if an incomplete message is received or if the signal is
interrupted during an alert, the 8-character display begins to flash.
The display stops flashing once the full message is received or the
SWS signal is reacquired.
Important: Your unit only displays safety warning messages when it
receives signals from an active Safety Warning System
transmitter.
14
Memory Retention Feature
The Memory Retention Feature retains the LRD 6699SWS’s operational
settings in memory for at least two days without power. When you turn
on the LRD 6699SWS, it will be in the same mode as when you turned it
off.
Audio/Dimmer Operation
Press the AUDIO button to select one of the following modes:
• DIMMER mode – dims your detector’s display. A “D” is displayed to
indicate this mode.
• AUDIO mode – turns your detector’s display off. An “A” is
displayed to indicate this mode.
(The mode indications ( CITY, AUDIO, or MUTE) remain on.)
Note: Do not set the Volume control at minimum while in this
mode because you’ll disable both alert types–visual
and audio.
• NORMAL mode – is the normal display mode.
15
Mute Operation
Press the MUTE button to briefly hear full audio when a signal is first
received, then the alert tone is automatically reduced to half volume for
the duration of the warning. An “M” is displayed to indicate this mode.
16
City/Highway Operation
In highly populated areas, you may encounter many devices that use the
same frequencies as radar signals, such as motion detectors, automatic
doors, and intrusion alarms. These devices may trigger an effect called
“falsing.”
Press the CITY button to change between Highway or City mode:
• CITY mode – filters most of the weaker radar signals and
significantly reduces “falsing.” In this mode, the combination of
visual and audio alert tones varies based on the strength of the signal
received. “CTY” is displayed to indicate this mode.
• HIGHWAY mode – has a lower signal threshold, which simply
means it doesn’t filter out weaker signals. Your detector will be more
sensitive to distant signals, but it also is more likely to “false.” Since
radar use declines significantly outside heavily populated areas, this
mode provides better long range detection while traveling long
distances. “HWY” is displayed to indicate this mode.
Note: If you use both Mute mode and City modes, you won’t receive an
alert until you are very close to the radar source.
17
LED Signal Strength Meter in City Mode
The LED signal strength meter gives you instant information about the
strength of the signal being detected. A weak signal causes the first LED
to light, but as signal strength increases, additional LEDs light. All LEDs
light when a full-strength signal is received. Use this meter to judge the
distance from the signal source.
Signal Strength
X-, K-, and Ka-Super
WideBand
Laser*
●❍❍❍❍❍
●●❍❍❍❍
●●●❍❍❍
●●●●❍❍
●●●●●❍
●●●●●●
Visual
Audio
Audio
Audio
Audio
Audio
Audio
Visual
Visual/Audio
Visual/Audio
Visual/Audio
Visual/Audio
*Note: Signal Strength for the Laser level is not displayed, only
‘LASER’ displays in the LED screen with an alert.
18
Care and Maintenance
The LRD 6699SWS is designed to give you years of trouble-free service.
There are no user-serviceable parts inside, and, except for the fuse, no
maintenance is required. To keep your detector in new condition, follow
these important suggestions:
• Never leave the LRD 6699SWS on the windshield when you park
your vehicle. The temperature in the vehicle in summer can reach
levels above what is considered safe for this unit.
• To make you less susceptible to break-in and theft, remove the unit
from your windshield when you leave your vehicle.
• Do not expose the unit to moisture. Rain, dew, road splash, or other
liquids can damage the internal components and reduce sensitivity of
the LRD 6699SWS.
19
Troubleshooting
If your LRD 6699SWS does not perform up to expectations, try the
suggestions listed below. If you cannot get satisfactory results, call the
Uniden Customer Service Center at (800) 297-1023, 8:00 a.m. to 5:00
p.m. Central Time, Monday through Friday.
Unit does not operate:
• Check the power cord. Be sure the connectors
are properly installed.
• Be sure ignition key is ON or in the
accessory position.
• Fuse out. Check and replace.
• Check power to lighter socket.
• Vehicle electrical problem exists.
• Make sure that the volume control is in the
ON position.
• Clean cigarette lighter socket.
Unit fails the self test.
Weak detection.
• Call Uniden Customer Service Center,
(800) 297-1023.
• Check angle of unit. Point to the horizon.
• Antenna/Sensor is obstructed. Relocate the unit
clear of any obstruction outside the windshield,
such as a wiper blade.
• Relocate the unit clear of the window tint.
Inaccurate or erratic
detection:
• Loose power cord.
Check both connectors.
• Power cord is broken. Check and replace.
Beeps over bumps or
rough road.
• Check that the power cord is connected at
both ends.
• Clean cigarette lighter socket.
Beeps at same location.
• Falsing because you have passed a motion
sensor or alarm.
Signal strength meter
registers, but no audio.
• For highway use, make sure the Highway mode
is ON.
• Increase the volume.
The unit bounces against
the windshield.
• Reposition so that the bumpers are firmly
against the windshield.
20
Specifications
General
Dimensions:
3 1/9 in.(W) x 4 5/8 in.(D) x 5/6 in.(H)
Weight:
3.5 oz.
Power Requirements:
Temperature Range:
13.8 VDC
Operating: -5°F to 160°F (-20°C to 70°C)
Storage: -40°F to 185°F (-40°C to 85°C)
360° Laser Detector
Receiver Type:
Sensor Front End:
Detector Type:
Receiver Bandwidth:
Spectral Response:
Alert Hold Time:
Pulse Laser Signal Receiver
Convex Condenser Lens
Pulse Width Discriminator
30 MHz
800 - 1100 nm
3 seconds
Radar Detector
Receiver Type:
Double Conversion Superheterodyne
Self-Contained Antenna
Detector Type:
Antenna Type:
Sensitivity:
Scanning Frequency Discriminator
Linear polarized, E vector vertical
X-band = -114 dBm/cm2
K-band = -104 dBm/cm2
Ka-SuperWideband = -100 dBm/cm2
10.490 - 10.560 GHz (X-band)
24.040 - 24.260 GHz (K-band)
33.40 - 36.00 GHz (Ka-SuperWideband)
Frequency of Operation:
Specifications are subject to change without notice.
21
Replacement Parts
Owner’s
Guide
Windshield Mounting
Clip
Fuses and
Spare Parts
Printed Material
Coiled Cigarette
Adapter
Straight Power Cord
22
SWS Warning Messages
Highway Construction
WORK ZONE AHEAD
ROAD CLOSED AHEAD / FOLLOW DETOUR
BRIDGE CLOSED AHEAD / FOLLOW DETOUR
HIGHWAY WORK CREWS AHEAD
UTILITY WORK CREWS AHEAD
ALL TRAFFIC FOLLOW DETOUR AHEAD
ALL TRUCKS FOLLOW DETOUR AHEAD
ALL TRAFFIC EXIT AHEAD
RIGHT LANE CLOSED AHEAD
CENTER LANE CLOSED AHEAD
LEFT LANE CLOSED AHEAD
Highway Hazard Zone Advisory
TRAIN APPROACHING / AT CROSSING
LOW OVERPASS AHEAD
DRAWBRIDGE UP
OBSERVE BRIDGE WEIGHT LIMIT
ROCK SLIDE AREA AHEAD
SCHOOL ZONE AHEAD
ROAD NARROWS AHEAD
SHARP CURVE AHEAD
PEDESTRIAN CROSSING AHEAD
DEER / MOOSE CROSSING
BLIND / DEAF CHILD AREA
STEEP GRADE AHEAD / TRUCK USE LOW GEAR
ACCIDENT AHEAD
POOR ROAD SURFACE AHEAD
SCHOOL BUS LOADING /UNLOADING
NO PASSING ZONE
DANGEROUS INTERSECTION AHEAD
STATIONARY EMERGENCY VEHICLE AHEAD
23
Weather Related Hazard
HIGH WIND AHEAD
SEVERE WEATHER AHEAD
HEAVY FOG AHEAD
HIGH WATER / FLOODING AHEAD
ICE ON BRIDGE AHEAD
ICE ON ROAD AHEAD
BLOWING DUST AHEAD
BLOWING SAND AHEAD
BLOWING SNOW AHEAD
BLOWING SNOW WHITE AREA AHEAD
Travel Information Convenience
REST AREA AHEAD
REST AREA WITH SERVICE AHEAD
24 HOUR FUEL SERVICE AHEAD
INSPECTION STATION OPEN
INSPECTION STATION CLOSED
REDUCED SPEED AREA AHEAD
SPEED LIMIT ENFORCED
HAZARDOUS MATERIALS EXIT AHEAD
CONGESTION AHEAD / EXPECT DELAY
EXPECT 10 MINUTE DELAY
EXPECT 20 MINUTE DELAY
EXPECT 30 MINUTE DELAY
EXPECT 1 HOUR DELAY
TRAFFIC ALERT / TUNE AM RADIO
PAY TOLL AHEAD
TRUCKS EXIT RIGHT
TRUCKS EXIT LEFT
Fast/Slow Moving Vehicles
EMERGENCY VEHICLE IN TRANSIT
POLICE IN PURSUIT
OVERSIZE VEHICLE IN TRANSIT
SLOW MOVING VEHICLE
24
One Year Limited Warranty
Important: Evidence of original purchase is required for
warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail
owner, this Uniden Product to be free from defects in materials and craftsmanship with
only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of
no further effect 12 months after the date of original retail sale. The warranty is invalid if
the Product is (A) damaged or not maintained as reasonable or necessary, (B) modified,
altered, or used as part of any conversion kits, subassemblies, or any configurations not
sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than
an authorized Uniden service center for a defect or malfunction covered by this warranty,
(E) used in any conjunction with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed
by the Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this
warranty at any time while this warranty is in effect, warrantor will either, at its option,
repair or replace the defective unit and return it to you without charge for parts, service, or
any other cost (except shipping and handling) incurred by warrantor or its representatives
in connection with the performance of this warranty. Warrantor, at its option, may replace
the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH
ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE
PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF
ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. This warranty is void outside the United
States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in this Operating Guide you are certain that the Product is
defective, pack the Product carefully (preferably in its original packaging). The Product
should include all parts and accessories originally packaged with the Product. Include
evidence of original purchase and a note describing the defect that has caused you to return
it. The Product should be shipped freight prepaid by traceable means to warrantor at:
Uniden America Corporation
Parts and Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023, 8:00 a.m. to 5:00 p.m. Central Time, Monday through Friday
Covered under one or more of the following U.S. patents:
4,622,553 4,698,632 4,709,407 4,791,420
4,831,498 5,315,302 5,469,287
®
©1998 Uniden America Corporation. All rights reserved.
Printed in the Philippines
|