DECT3181 Series User's Guide
You will also find:
What's in the box?
DECT3181 base
with answering
system and
Accessory handset and charger
(DCX310 displayed)
cordless handset
For each accessory
handset (not pictured):
-
Rechargeable battery
(BT-1018)
-
-
Battery cover
Charger AC adapter
If you purchased
model number:
DECT3181
DECT3181-2
DECT3181-3
:
You should
have:
None
1 Accessory HS
2 Accessory HS
:
Battery
cover
Not pictured:
-
Rechargeable battery
(BT-1018)
-
-
AC adapter (PS-0034)
Telephone cord
DECT3181-12 11 Accessory HS
If any items are missing or damaged, contact our Customer Care Line
immediately. Never use damaged products!
If You...
Contact Uniden’s... Phone Number
817-858-2929 or
800-297-1023
have a question or problem
Customer Care Line*
need a replacement part or an
accessory
Parts Department*
800-554-3988
need special assistance due to
a disability
800-874-9314
(voice or TTY)
Accessibility Help Line
* During regular business hours, Central Standard Time; see our website for detailed busi-
ness hours.
© 2010 Uniden America Corp.
Printed in Vietnam
Ft.DWoorwthn, Tleoxaasd from Www.Somanuals.com. All Manuals Search And DUoNwZZn0l1o17a8dBZ.(0)
What’s in the manual?
ImPOrTANT SAfETY INSTrUCTIONS!
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
This unit is NOT waterproof. DO NOT expose this unit to rain or
moisture.
Do not use this product near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement, or near a
swimming pool.
Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
3
Do not use the telephone to report a gas leak in the vicinity of the
leak.
Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check with
local codes for possible special disposal instructions.
Do not place the handset in any charging cradle without the battery
installed and the battery cover securely in place.
SAVE THESE INSTrUCTIONS!
CAUTION! risk of explosion if battery is replaced by an
incorrect type! Dispose of used batteries according to the
instructions. Do not open or mutilate the battery. Disconnect
the battery before shipping this product.
For more details, see the Important Information section.
GETTING STArTED
Installing Your Phone
Charge the baꢀery
1. Unpack all handsets, batteries, and
battery covers. If you need to remove a
battery cover, press in on the notch and
slide the cover down.
2. Line up the battery connector with the jack inside the handset and
push the connector in until it clicks into place. Tug gently on the
wires to make sure the battery pack is securely connected.
3. Replace the cover and slide it up into place.
4. Connect the base AC adapter to the ac in 7.8V jack on the base. Run
the cord through the indent and out the back.
5. If you have accessory handsets, connect each charger’s applicable AC
adapter to the power jack.
If you have a DRX312 handset with a MULTIRANGE charger or
a DWX317 waterproof handset, be sure to use the correct AC
4
adapter for the charger. See the separate DRX312 or DWX317 user
guide that was packaged with your phone.
6. Plug the other end of each adapter into a standard 120V AC power
outlet.
7. Place one handset in the base and the other(s) in the charger(s) with
the display(s) facing forward. The display on the handset should light
up; if it doesn’t, reseat the handset or try plugging the AC adapter
into a different outlet.
Charge all handsets completely (about 15 hours) before using
them.
Connect the telephone cord
Connect the TEL LinE jack to a standard telephone wall jack.
Test the connecꢁon
1. Pick up the handset from the cradle and press TaLk/fLash. You
should hear a dial tone, and the display should say Talk
.
If you don't hear a dial tone, try checking the connection between
the base and the phone jack.
2. Make a quick test call. (Press End to hang up.)
If the tone doesn’t stop when you dial, try changing to pulse dialing
avoiding interference.
3. Test any accessory handsets the same way. If you can’t get a dial
tone or the handset display says Unavailable, try resetting the
Seꢃng Up the CellLink™ Bluetooth™ Connecꢀon
The new DECT3181 with CellLink technology can connect with mobile
phones that support the Bluetooth V2.0 handsfree profile.
Visit Uniden.com or contact customer service for a detailed list of tested
mobile phones.
5
If you are not certain of the profiles supported by your Bluetooth
phone or if you have difficulty pairing your phone to the DECT3181,
see the manual that came with your phone.
With the CellLink feature, you can essentially treat your cellular
phone as a second line. You can use the DECT3181 handset to make
and receive calls on your cellular phone number, put cellular calls
information.
Bluetooth wireless devices have a maximum range of about 10
feet (3 m); the actual range will vary depending on local conditions
(obstacles, battery power, interference, etc.).
Pair your Bluetooth phone
Pairing “introduces” two Bluetooth devices and gives them permission
to connect to each other. In most cases, once you pair a phone to the
DECT3181, the two devices connect automatically whenever they detect
each other. (If you have to manually reconnect each time, check the
Bluetooth settings on your cellular phone.) You can pair your Bluetooth
devices through the DECT3181 handset.
1. Press MEnu/sELEcT to display the handset’s main menu.
2. Select the Bluetooth menu, then select the Add Cellular submenu.
The LED on the base begins to flash and the base goes into pairing
mode when the handset displays Use Cellular to Pair (PIN 0000).
3. On your Bluetooth phone, start a search for other Bluetooth devices.
(This process may take several seconds and it will be different for
each mobile phone. See your phone owner’s manual for detailed
instructions.)
4. Your phone should discover a device called DECT3181 or Handsfree
device. When your phone asks if you want to pair with this device,
answer yes.
5. If your phone prompts you for a PIN code or password to pair with
the DECT3181, enter 0000 (four zeroes).
6. When your phone accepts the Bluetooth connection, the DECT3181
sounds a confirmation tone. The Bluetooth LED on the base and the
Bluetooth status icon on the handset display, remain lit.
6
most cellular phones automatically transfer the audio to a
Bluetooth device as soon as it pairs; if yours does not, look in
your cellular phone’s Bluetooth setup for a “transfer audio”
or “send audio to device” option.
To test the connecꢁon
1. Pick up the handset from the cradle.
2. Dial the number you want to call, then press cELLLink on the
handset. You may not hear a dial tone or ringing, but the handset
display says Talk
.
3. Make sure the call connects and you can hear clearly. (When you’re
finished, press End to hang up.)
The DECT3181 remembers the pairing information for your cellular;
if it loses connection with your phone for any reason (e.g., the
cellular phone travels out of range, runs out of charge, etc.), the
DECT3181 can automatically reconnect the next time your phone
becomes available.
Using the DECT3181 with four Bluetooth phones
The DECT3181 can save the pairing information for four different
Bluetooth phones, but it can only use one cellular line at any given
time. For example, if you pair the DECT3181 to four Bluetooth
phones, when you press cELLLink on the handset, the DECT3181
asks which phone you want to connect to.
If you are using the DECT3181 to talk on one Bluetooth phone, the
DECT3181 will not ring if a call comes in on another phone.
You can set a different ring tone for each paired cellular phone (see
To pair another Bluetooth phone, just repeat the pairing procedure
with the new phone. (If the paired phones interfere when you’re
pairing the new one, just turn off Bluetooth on any paired phones
until you finish pairing the the new one.)
7
TM
Seꢃng Up MULTIRANGE Chargers
If the model number ends in an r, at least one of the chargers
included with your phone is a MULTIRANGE charger.
The MULTIRANGETM charger extends the range of your base in all
directions, including up and down. Each handset will automatically
connect to the charger or the base, depending on which signal is stronger.
If your phone includes a MULTIRANGE charger, you will have a
separate manual discussing the charger in detail, including how it
works, how to reset it, etc.
Your base supports a total of 2 DRX312 MULTIRANGE chargers,
including any that were supplied with your phone.
Any MULTIRANGE charger included with your phone is ready to use
out of the box. Just pick the best location and plug it in.
To place a MULTIRANGE charger
Make sure you have a strong signal from the base (at least 3 bars in
the handset display).
Put the charger at least 35 feet away from the base or any other
MULTIRANGE charger. (If you put the charger on a different floor
from the base, don't forget to allow 35 feet vertically, also.)
for more information, see the DrX312 user guide.
8
UNDErSTANDING YOUr PHONE
Parts of the Base
MESSAGE
COUNTER
DOWN UP
ON/OFF
DO NOT
DISTURB
PLAY/
STOP
DELETE
Charging
contacts
FWD
FIND
REV
Base keys and how they work
Key name (and icon)
What it does
find
-
In standby: page all handsets to find a lost
one.
dO nOT disTuRB
-
In standby: turn the Do Not Disturb
(
)
On/Off
-
-
In standby: turn the answering system on
or off.
REV
While a message is playing: for the first
2 seconds, go to the previous message;
after that: go to the start of this message.
(
)
9
Key name (and icon)
What it does
PLaY/sTOP
-
-
In standby: start playing messages.
While a message is playing: stop playing
messages.
(
)
-
-
While the phone is ringing: mute the
ringer for this call only.
fWd
While a message is playing: skip to the
next message.
(
)
dELETE
-
While a message is playing: delete this
message.
In standby: delete all messages.
While Bluetooth phone is ringing: reject
the call.
(
)
-
-
-
In standby: decrease the ringer volume.
dOWn (–)
-
While a message is playing: decrease the
speaker volume.
-
-
In standby: increase the ringer volume.
While a message is playing: increase the
speaker volume.
uP
(+)
10
Parts of the Handset
Visual
ringer
Earpiece
Display
MENU/
SELECT
UP
CELL LINK
CLEAR/
INTERCOM
CID/RIGHT
PHONEBOOK/
LEFT
TALK/
FLASH
END
Twelve-
key dial
pad
DOWN
MESSAGES/
MUTE
REDIAL/
PAUSE
SPEAKER
Microphone
Charging
contacts
Handset keys and how they work
Key name (and icon)
What it does
-
-
-
In standby: increase the ringer volume.
During a call: increase the call volume.
In the menu or any list: move the cursor
up one line.
In standby or during a call: open the
Caller ID list.
uP
(
)
(
-
-
cid/RighT
)
During text entry: move the cursor to
the right.
11
Key name (and icon)
What it does
-
-
-
In standby: decrease the ringer volume.
During a call: decrease the call volume.
In the menu or any list: move the cursor
down one line.
dOWn
(
)
-
-
In standby: open the menu.
In the menu or any list: select the
highlighted item.
MEnu/sELEcT
-
-
During a call: hang up.
In the menu or any list: exit and go to
standby.
End
(
)
-
-
-
In standby: page another handset using
the intercom.
During a call: put the call on hold and
start a call transfer.
While entering text: delete one
character, or press and hold to delete all
the characters.
In standby or during a call: open the
phonebook.
In a menu: go back to the previous
screen.
During text entry: move the cursor to
the left.
In standby: start a telephone call on
your land line (get a dial tone).
While the land line is ringing: answer the
incoming call.
cLEaR/inTERcOM
PhOnEBOOk/LEfT
-
-
-
-
-
(
)
TaLk/fLash
(
)
-
-
During a call: switch to a waiting call.
Switch a call to the speakerphone (and
back).
sPEakER
(
)
12
Key name (and icon)
What it does
-
In standby: open the redial list.
-
While entering a phone number: insert a
2-second pause.
REdiaL/PausE
(
)
-
-
-
-
In standby: start a telephone call using
your paired Bluetooth phone.
While the Bluetooth phone is ringing:
answer the incoming call.
During a CellLink call: switch to a waiting
call.
In standby: access your answering
system.
cELLLink
(
)
-
-
During a call: mute the microphone.
While the phone is ringing: mute the
ringer for this call only.
MEssagEs/MuTE
(
)
Display icons and what they mean
Since the icons appear based on what you’re doing with the phone, you
won’t ever see all of these icons at the same time.
Icon
What it means
The ringer is turned off: this handset will not ring
when a call comes in.
Privacy Mode is on: no other handset can join your
call.
The speakerphone is on.
The microphone is muted, and the caller can’t hear
you.
13
Icon
What it means
T-coil mode is on (see page 36).
The battery is 1) empty, 2) getting low, 3) half
charged, or 4) fully charged.
The signal from the base is 1) weak, 2) low, 3)
strong, or 4) very strong.
[Aa]
[aA]
The handset enters lower-case letters first (see page
17).
At least 1 cellular phone is paired to the DECT3181.
Using the menus
To open the
menu, press
MENU/SELECT.
Press MENU/SELECT
to choose the
highlighted option
.
The cursor
shows the
highlighted
option.
To move the
cursor, use
UP & DOWN.
Bluetooth
<BLUETOOTH>
Day & Time
Handset Setup
Add Cellular
Paired Device
To go back a
screen, press
PHONEBOOK/LEFT
press EN
exit the
OR
menu
.
14
If you open the menu during a call, use PhOnEBOOk/LEfT to back out
of the menu without hanging up.
If you don't press any keys for 30 seconds, the handset exits the
menu.
The Bluetooth menu
You can pair up to 4 cellular devices to the DECT3181.
Setting
What it does
Add Cellular
The base goes into pairing mode. The handset
displays a prompt to pair the cellular. Follow the
cellular’s procedures to pair the device with the
DECT3181.
Paired Device
A list of paired devices displays. Select a device.
The following two menus display:
- Remove Paired. This option allows you to
delete the pairing information for the selected
cellular phone.
- Privacy Setup. Only handsets set to On will ring
with an incoming call.
If all handsets are set to Off (default),
then all handsets will ring.
Privacy Setup only affects the ring; other
handsets will still get CID information
and be able to use the cellphone for
outside calls.
15
The Day and Time menu
If you subscribe to Caller ID, the phone automatically sets the day and
time when it receives Caller ID information from your phone company. If
you want to set the clock manually, just open the menu and select Day
and Time. The phone prompts you to select the day, enter the time, and
select AM/PM. (When prompted for the time, use the number keypad
to enter 2 digits for the hour and 2 digits for the minutes, e.g., 0530 for
5:30.)
The Handset Setup Menu
You can change these settings separately for each handset.
Setting
What it does
Turn on T-coil mode to reduce noise on some hearing
aids (see page 36).
T-coil
You can set a different ring tone for the land line and
each paired cellular phone. First, select the line you
want to set the ring tone for. Then, select the ring
tone that you want this handset to use for that line.
Ringer Tones
As you highlight each ring tone, the phone plays a
sample. When you hear the tone you want, press
MEnu/sELEcT.
Turn on the personal ring feature. This feature lets
you assign special ring tones to people in the cordless
phone’s local phonebook. When someone in your
phonebook calls, this handset uses the assigned ring
tone. (It doesn’t matter what line the person calls on,
as long as you have Caller ID service on that line.)
Personal Ring
Banner
Change the name used on the handset’s display.
Handset
Language
Change the display language.
Key Touch Tone Have the keypad sound a tone when you press a key.
16
The Ans. Setup menu
This menu controls the options and settings for your answering system
The Global Setup menu
The settings on this menu affect all handsets and the base. Before
changing these settings, make sure the phone is in standby and all
handsets are within range of the base. (Only one handset at a time can
change these settings.)
Setting
What it does
Change the way your phone communicates with
Dial Mode
Do not change this setting unless instructed to by
customer service.
Reset the message waiting indicator if it gets out of
Set Line Mode
VMWI Reset
How to enter text on your phone
Use the 12-key dial pad when you want to enter text into your phone (a
name in the phonebook, the handset banner, etc.).
The phone defaults to a capital letter for the first letter and any letter
after a space; otherwise, it uses small letters.
To switch to all capital letters, press . The phone defaults to all
*
capital letters first (e. g. ABCabc2) until you enter a blank space or
press again. (Any time you want to change case, just press .)
*
*
If two letters in a row use the same number key, enter the first letter
and wait a few seconds (or press RighT); the cursor will move to the
next space. Enter the next letter.
Press to enter a blank space.
To change a letter, move the cursor to that letter and press cLEaR to
erase the letter; enter the new one.
#
To erase the entire entry, press and hold cLEaR
.
Press to cycle through all available symbols and punctuation.
0
17
USING YOUr PHONE
You can control the features in this section through the handset.
Learning the Basics
To...
from the land line from the cell phone
make a call: Dial the
number, then
Press TaLk/fLash or
Press cELLLink.*
sPEakER.
Press TaLk/fLash or
Press cELLLink.
sPEakER.
Press End or put the handset in the cradle.
answer a call
hang up
mute the microphone
during a call
Press MEssagEs/MuTE. Press again to turn the
microphone back on.
Press cLEaR/inTERcOM. After 5 minutes on
hold, the call will be disconnected.
put a call on hold
Press TaLk/fLash or
Press cELLLink.
sPEakER.
return to a call on hold
Press cELLLink.*
Press TaLk/fLash. The
The handset
switch from one line to
the other (automatic
hold)
handset automatically
automatically puts
puts the CellLink line
the land line on hold
on hold and connects
and connects to the
to the land line.
cell phone.
switch between the
speakerphone and
earpiece
Press sPEakER.
While the phone is ringing, press MEssagEs/
MuTE on the handset or PLaY/sTOP on the
base.
mute the ringer for this
call only
* If you have two or more cellular phones paired, the phone prompts you
to choose one. Select the phone you want and press MEnu/sELEcT.
18
Change the volume
Speaker and earpiece
volume
ringer volume
-
-
-
You can change the volume
of the speaker on the base
and each cordless handset
separately.
-
-
-
You can change volume of the
ringer on the base and each
handset separately.
Each cordless handset uses the
same ringer volume for both the
land line and the cellular line.
When the phone is in standby,
press uP to increase the volume
and dOWn to decrease it.
If you turn the ringer volume all
the way down, the ringer turns
off.
You can change the volume of
the earpiece on each handset;
this does not affect the
handset’s speaker volume.
Anytime you are listening to a
speaker or earpiece, press uP
to increase the volume and
dOWn to decrease it.
-
Call waiꢁng
Call Waiting is a service available from your telephone provider that lets
you receive calls while you are on another call. Caller ID on Call Waiting
(CIDCW) service displays Caller ID information for a waiting call. You might
have to subscribe to these services separately for your land line and your
cellular phones. Contact your telephone provider(s) for more information.
If you get a Call Waiting call, the phone sounds a tone and displays any
CID information received for the waiting call. To switch between the
current call and the waiting call, press TaLk/fLash (if you’re on the land
line) or cELLLink (if you’re on a cellular line). Remember, each time you
switch, there is a short pause before you’re connected to the other caller.
Using Caller ID and Redial Lists
Caller ID (CID) is a service available from your telephone provider that
shows the phone number (and sometimes the caller’s name) of incoming
calls. You might have to subscribe to CID service separately for your land
19
line and your cellular phones. Contact your telephone provider(s) for
more information.
On CellLink calls, you might see the name of your cellular
phone in place of the caller’s name.
Caller ID List
Redial List
-
The phone saves the information for
the last 30 received calls to the CID list.
Land line calls and CellLink calls are
saved to the same CID list. The CID list
is shared by all cordless handsets. New
records have an asterisk next to the
received time.
When the phone’s in standby, each
handset shows how many calls came
in since the last time you checked the
CID list.
-
Each cordless handset
remembers the last 5
numbers you dialed
on it.
The redial list is separate
for each handset;
however, only one
handset can access the
redial list at a time.
The handset doesn’t
record which line was
used to call the number.
-
-
-
-
Only one handset can access the CID
list at a time.
To…
follow these steps …
open the CID list
Press cid/RighT.
open the Redial list Press REdiaL/PausE.
scroll through the Press dOWn to scroll through the list from newest
list
to oldest. Press uP to scroll from oldest to newest.
Find the number you want* and press TaLk/fLash
dial a number
close the list
or cELLLink †.
Press PhOnEBOOk/LEfT.
* If the number is a toll or long distance call, but there’s no
1
at the front
of the CID record, press to add the
1
before you dial the number.
*
20
† If you have two or more cellular phones paired, the phone prompts you
to choose one. Select the phone you want and press MEnu/sELEcT.
To select a number, highlight the number and press MEnu/sELEcT. The
phone gives you the following options:
Option
What it does...
Delete Entry Erase the number from the list.
Add the number to the phonebook. The handset prompts
you to edit the name and number and select a personal
ring.
Store Into
Pb
(Caller ID list only.) Erase all numbers from the list.
(This does not affect the CID lists on the paired cellular
phones.)
Delete All
Using the Directory
You can download the phonebook from each paired cellular phone
(up to four) and store a copy in the local directory. Each downloaded
phonebook can be up to 1500 entries.
You can also store up to 70 entries in the DECT3181’s Home
phonebook, which is separate from any downloaded phonebooks.
You can edit or delete individual entries in the Home phonebook only.
If you need to edit an entry on a downloaded phonebook, edit the
entry on your cellular phone, then re-download the phonebook.
Only one cordless handset can access the directory at a time.
Downloading phonebooks into the directory
1. Make sure your cellular phone is paired to the DECT3181 and is
within range of the base.
2. With the DECT3181 in standby, press PhOnEBOOk/LEfT on any
cordless handset.
3. Select Download, then select the cellular phone you want to
download from. The DECT3181 begins downloading the phonebook
from the cellular phone. When downloading is complete, the
cordless handset displays a confirmation screen. To cancel
downloading, press End on the handset.
21
Each time you download the phonebook from a paired cellular phone,
the DECT3181 overwrites any previous copy of that phonebook in its
directory. The phone automatically cancels the download if it receives an
incoming call or someone tries to make an outgoing call.
While a phonebook is downloading, do not try to use either the cellular
phone or the DECT3181. If the download is interrupted or canceled, the
DECT3181 reverts to the original copy of the downloaded phonebook in
its directory.
If you delete the pairing information for a cellular phone, the downloaded
phonebook from that phone will also be deleted.
Using a phonebook
1. To open the directory, press PhOnEBOOk/LEfT. The handset displays
the list of available phonebooks: the Home phonebook and up to
four downloaded phonebooks.
2. Highlight the phonebook you want to use, then press MEnu/sELEcT.
3. The handset displays the name of the phonebook and the number of
entries in the phonebook.
To...
follow these steps...
Press dOWn to scroll through the entries
from A to Z or uP to scroll from Z to A.
scroll through the entries
jump to entries that start Press the number key corresponding to
with a certain letter
the letter you want to jump to.
Find the entry you want to dial, and
press TaLk/fLash or cELLLink.
If you have two or more cellular phones
paired, the phone prompts you to chose
one. Select the phone you want to use
and press MEnu/sELEcT.
dial an entry
If the phonebook entry is for a toll/
long distance call but does not begin
with 1, press * to add 1 before dialing.
22
To...
follow these steps...
Find the entry you want to edit. Press
MEnu/sELEcT and select Edit. The
handset prompts you to edit the name
and number and select a personal ring.
edit an entry (Home
phonebook only)
Find the entry you want to delete. Press
MEnu/sELEcT and select Delete. When
the handset prompts you to confirm,
delete an entry (Home
phonebook only)
select Yes
.
Phonebook menu opꢁons
With the phone in standby, open the directory and select the phonebook
you want to use. From the main phonebook screen (instead of an
individual entry), press MEnu/sELEcT. The phone gives you the following
options:
Option
What it does...
Create New
Add an entry to your phonebook. The handset
(Home phonebook prompts you to enter a name and number and
only)
select a personal ring.
Delete All
Erase all the entries in the phonebook.
Finding a Lost Handset
With the phone in standby, press find on the base. All the handsets will
beep for 1 minute; to end the page, press find again or press any key on
any handset.
Using Mulꢀ-Handset Features
To use the features in this section, you must have at least two cordless
handsets.
23
Expanding your phone
Your base supports a total of 12 cordless handsets: the one that came
with the base and up to 11 DCX310, DRX312, or DWX317 accessory
handsets.
Your base might be compatible with other Uniden accessory
handsets: please visit our website for a list of compatible handsets.
Accessory handsets must be registered to the base before you can
use them. Handsets that aren't registered display a Handset not
registered message. For instructions on registering handsets to the
Any accessory handsets that came packaged with the base are already
registered for you.
If a handset was previously registered to a base, you have to reset it
the accessory handset).
Conference calling
When an outside call comes in on the land line, two handsets can join
in a conference call with that outside caller.
To join an ongoing call, press TaLk/fLash or sPEakER.
To leave the conference call, hang up normally; the other handset
remains connected to the call.
Privacy mode
You can prevent other handsets from joining a land line call. Start your
call as usual, then press MEnu/sELEcT: the display shows Call Privacy
Press MEnu/sELEcT again to turn privacy mode on (you’ll see in the
display). When you hang up, privacy mode turns off automatically.
.
As long you have privacy mode on, no other handsets can interrupt your
call. To allow another handset to join the call, press MEnu/sELEcT twice
to turn privacy mode off.
24
Call transfer
To…
On the land line
Using CellLink
Press cLEaR/inTERcOM, then select the
handset you want to transfer the call to
(select All to page all the handsets). When
the other handset accepts the call, you’ll be
disconnected.
transfer a call
cancel a transfer and
leave the call on hold
Press End.
return to the call
Press TaLk/fLash.
Press cELLLink.
1. Press cLEaR/inTERcOM. You can speak to
the transferring handset.
2. To speak to the outside caller,
answer a call transfer
page
press TaLk/fLash.
press cELLLink.
Intercom
Whenever the phone is in standby, you can make an intercom call
between handsets without using the phone line.
You can make an intercom call from any handset, but only two
handsets can be in an intercom call at any time.
If an outside call comes in during an intercom page, the phone sounds
a tone and shows any received CID information. If another handset
hasn't answered the page yet, the phone cancels the page to let you
can answer the incoming call.
To...
follow these steps...
Press cLEaR/inTERcOM, then select the
handset you want to talk with (select All
to page all handsets at the same time).
make an intercom page
cancel a page
Press End.
answer an intercom page
leave an intercom call
Press cLEaR/inTERcOM or TaLk/fLash.
Press End.
25
To...
follow these steps...
Press TaLk/fLash or cELLLink (depending
answer an outside call
during an intercom call
on which line is ringing). The phone
automatically disconnects the intercom
call and connects you to the outside line.
Using Special features
Do Not Disturb (DND)
The Do Not Disturb feature (DND) turns off the ringers on the base
and all handsets at the same time.
You can turn on DND from the base whenever the phone is in
standby: just press and hold dO nOT disTuRB for about a second. The
phone automatically turns on the answering system and shows Do
Not Disturb on all handsets.
To turn DND off, press dO nOT disTuRB again.
If you turn the answering system off while DND is on, the phone turns
off DND along with the answering system.
Chain dialing
If you often have to enter a series of digits or a code number during
a call, you can save that code number to a phonebook entry and use
the phonebook to send the code number.
Enter the code number (up to 20 digits) into the phonebook just like a
regular phonebook entry. Be sure to enter the code number into the
phonebook exactly as you would enter it during a call.
When you hear the prompt that tells you to enter the number, open
the phonebook and find the entry that contains your code number.
Press MEnu/sELEcT to transmit the code. Or, if you change your mind,
use PhOnEBOOk/LEfT to close the phonebook.
Voice message noꢁficaꢁon
This feature supports Frequency-Shift Keying (FSK) message
notification. Contact your voice mail provider for more details.
If you subscribe to a voice mail service, your phone can notify you
when you have a new message waiting.
26
When you have new messages, the voice message icon (
)
appears in the display, and the light at the top of the handset blinks.
The voice message icon should disappear after you listen to all your
new messages. If it doesn’t, you can reset it manually: With the phone
in standby, open the menu and select Global Setup. Select VMWI
Reset, then select Yes
.
USING THE ANSWErING SYSTEm
The answering system works with land line calls only. The system will
not answer or take messages on incoming call on the paired Bluetooth
phones.
Answering System Opꢀons (Ans. Setup)
You can change the answering system options from any handset. Just
open the menu and select Ans. Setup. Select one of the following:
Setting
What it does...
Enter a 2-digit PIN so you can access your answering
Security Code
Set the number of rings (2, 4, or 6) before the
answering system answers the phone. Choose Toll
Saver to have the system answer after 2 rings if you
have new messages or after 4 rings if you don’t.
Ring Time
Set the amount of time callers have to leave a message,
either 1 minute or 4 minutes. Choose Announce Only
if you don’t want the system to let callers to leave a
message.
Have the system beep every 15 seconds when you have
a new message; the beeping stops when you listen
to all your new messages. (To mute the alert without
listening to your messages, press any key on the base.)
Record Time
Message Alert
Ans.
Language
Change the language of the system’s voice prompts.
27
Setting
What it does...
Turn on the call screen feature so you can hear callers
as they leave messages on the base speaker (see page
30).
Call Screen
Turn your answering system on or off. (To turn your
system on or off from the base, just press On/Off.)
Ans. On/off
Accessing the Answering System
You can access your system from a handset whenever the phone is in
standby.
Press MESSAGES/
MUTE to start remote
operation mode.
5:Stop
[
/
/select]
Press MENU/SELECT
to choose the
displayed
option.
Use PHONEBOOK/
LEFT to go to the
previous option:
Use CALLER ID/
RIGHT to go to
the next option:
4:Delete
3:Skip
6:SelectGreeting
8:RecNewGreeting
Press END to exit
remote operation
mode.
2:Play
1:Repeat
During remote operation, the phone beeps to let you know it's
waiting for your next command.
You can press the number key next to the commands instead of
scrolling through them.
If you don't press any keys for 30 seconds, the phone returns to
standby.
Only one handset can access the system at a time, and you can't
access the system while another handset is on a land line or CellLink
call.
28
Personalizing Your Greeꢀng
Your greeting can be between 2 seconds and 30 seconds long. If you don’t
record an outgoing message, the system uses a pre-recorded greeting:
Hello, no one is available to take your call. Please leave a message after
the tone.
Record your personal outgoing message or greeꢁng
1. Access the system from any handset. Wait until the system finishes
its announcements, or press
2. Press
3. Wait for the system to say “Record greeting,” then begin speaking.
5
(Stop) to skip them.
8
(RecNewGreeting).
4. When you’re finished, press
8
(RecNewGreeting) to recording.
The system plays back your new greeting.
5. To keep this greeting, press End. To re-record it, go back to step 2.
Switch between the two greeꢁngs
1. Access the system from any handset. Wait until the system finishes
its announcements, or press
5
(Stop) to skip them.
2. Press
3. Press
6
(
(
SelectGreeting) to play back the current greeting.
SelectGreeting) again to switch greetings.
6
Delete your greeꢁng
Switch to your personal greeting following the steps above. While the
system is playing back your greeting, press
4
(Delete).
Geꢃng Your Messages
from a handset
(remote operation)
To…
from the base
Press PLaY/sTOP.
Press MEssagEs/MuTE.
The system announces the number of new and old
messages, then plays each new message (followed
by the time and date) in the order it was received.
play new messages
29
from a handset
(remote operation)
To…
from the base
Within the first 2 seconds of a message,
replay an earlier
message
press REV.
select 1:Repeat.
Wait at least 5 seconds
after the message
starts, then select 1:
Repeat.
Wait at least 4 seconds
after the message starts,
then press REV.
restart the current
message
skip a message
Press fWd.
Select 3: Skip.
While the message is
playing, press dELETE.
While the message is
playing, select 4:Delete.
delete a message
With the phone in
standby, press dELETE.
When the system asks
you to confirm, press
dELETE again.
delete all of your
messages
Not available.
After the system plays the new messages,
press PLaY/sTOP again. Select 2:Play.
play old messages
stop playback
Press PLaY/sTOP.
Select 5: Stop.
Screening Your Calls
Another feature your answering system gives you is call screening. While
the system is taking a message, you can hear the caller on the base
speaker (if you turn on Call Screen) or from a handset. Only one handset
at a time can screen calls. If another handset is screening the call, the
handset beeps and returns to standby.
To...
from the base
from a handset
Press MEssagEs/MuTE.
Press TaLk/fLash.
Just listen to the
caller over the
speaker.
hear the caller
leaving a message
answer the call
Not available.
30
To...
from the base
from a handset
Press End or return the
handset to the cradle.
Press PLaY/sTOP.
mute the call screen
without answering
If you mute the call screen, the system continues
taking the message: it just stops playing through
the speaker.
Using the System While You’re Away from Home
You can also use your answering system from any touch-tone phone.
Before you can use this feature, you must program a security code.
Programming a security code
1. With the phone in standby, open the menu from any handset.
2. Select Ans. Setup, then select Security Code
.
3. Use the number keypad to enter a two-digit security code (01 to 99).
Press MEnu/sELEcT when you’re finished.
remember to make a note of your new security code!
Dialing in to your system
1. Call your telephone number and wait for the system to answer.
If you have the Ring Time set to Toll Saver, the system answers
after 2 rings if you have new messages and 4 rings if you don’t. You
can hang up during the third or fourth ring.
If your answering system is off, it will answer after about ten rings
and sound a series of beeps instead of your greeting.
2. During the greeting (or beeps), press and immediately enter your
0
security code. (If you enter it incorrectly 3 times, the system hangs
up and returns to standby.)
3. The system announces the current time, the number of messages
stored in memory, and a help prompt. Then it starts beeping
intermittently to let you know it's waiting for your command.
4. When you hear the intermittent beeping, enter a command from the
chart:
31
01
02
03
04
Repeat message
Play message
Skip message
05
06
09
10
Stop playback
Turn on
Turn off
Delete message
Hear prompts
If you don’t press any keys for 15 seconds, the phone will
hang up and return to standby.
ImPOrTANT INfOrmATION
Solving Problems
If you have any trouble with your phone, try these simple steps first. If
you need help, call our Customer Care Line listed on the front cover.
If…
Try…
-
-
-
Checking the telephone cord connection (for
land line calls).
No handsets can
make or receive calls.
Disconnecting the base AC adapter. Wait a few
minutes, then reconnect it.
Making sure the base is plugged in.
A handset can’t
make or receive calls.
Moving the handset closer to the base.
-
-
-
Making sure the ringer is turned on.
Making sure Do Not Disturb is turned off.
Checking the privacy settings for your paired
cellular phones.
A handset can make
calls, but it won’t
ring.
-
-
-
-
-
Charging the battery for 15-20 hours.
Checking the battery connection.
Resetting the handset.
Moving the handset closer to the base.
Seeing if another handset is in Privacy Mode.
A handset is not
working.
A handset says
Unavailable.
32
If…
Try…
-
-
Letting calls ring twice before answering.
Making sure your Caller ID service is active.
No handsets display
Caller ID information.
Caller ID displays
briefly and then
clears.
-
You may have to change the line mode. Contact
customer service.
I can’t transfer calls. Resetting all handsets.
-
-
Making sure no handset is in Privacy Mode.
Two handsets can’t
talk to the caller.
Making sure the call was on the land line
(conference calling is not available for CellLink
calls).
The answering
system does not
work.
-
-
Making sure the answering system is on.
Making sure the base is plugged in.
-
Making sure Record Time is not set to
Announce Only.
The system won’t
record messages.
-
-
Deleting messages (memory may be full).
Making sure the call was on the land line (the
system cannot answer CellLink calls).
A handset can’t
access the answering
system.
-
-
Seeing if another handset is using the system.
Making sure the phone is in standby.
-
Making sure your phone has Bluetooth turned
on.
-
-
Making sure your phone is in range of the base.
The DECT3181
doesn’t ring when
my cellular phone
does.
Checking if the DECT3181 is on the paired
device list on your cellular phone and is in
connected status. If not, try pairing again.
Making sure your phone doesn’t connect with
other Bluetooth devices.
-
-
Making sure the handset’s ringer is not turned
off. (The base doesn’t ring on cellular calls.)
33
If…
Try…
-
Making sure your phone is in pairing mode.
-
Check your phone’s manual for instructions on
Bluetooth device pairing.
-
Making sure your phone supports the
Bluetooth hands-free profile.
-
-
Making sure your phone is in range of the base
If DECT3181 appears in your cellular phone’s
paired device list, remove it and try pairing
again.
The DECT3181 won’t
pair with my phone.
-
-
Turn your phone off, then turn it on again.
Repeat pairing steps.
Disconnecting the base AC adapter. Wait a
few minutes, then reconnect it. Repeat pairing
steps.
-
Checking the link order for that phone. In rare
cases, some cellular phones may not be linked
as the third or fourth cellular phone.
-
-
Adjusting the handset volume.
Setting your cellular phone to transfer the
audio to a Bluetooth device. Check your
phone’s manual for instructions on Bluetooth
setup and options.
Erase all Bluetooth pairing and repair again. To
erase the Bluetooth pairing, see page 15.
The DECT3181 paired
with my phone, but
I can’t hear anything
through the handset.
-
Weak or hard to hear audio
If a caller’s voice sounds weak or soft, the signal might be blocked by large
metal objects or walls; you might also be too far from the base, or the
handset’s battery may be weak.
Try moving around while you’re on a call or moving closer to the base
to see if the sound gets louder.
Make sure the handset’s battery is fully charged.
Try adjusting the earpiece volume.
34
Noise or staꢁc on the line
Interference is the most common cause of noise or static on a cordless
phone. Here are some common sources of interference:
electrical appliances, especially microwave ovens
computer equipment, especially wireless LAN equipment and DSL
modems
radio-based wireless devices, such as room monitors, wireless
controllers, or wireless headphones or speakers
fluorescent light fixtures (especially if they give off a buzzing noise)
other services that use your phone line, like alarm systems, intercom
systems, or broadband Internet service
If static is on 1 handset or in 1 If static is on all handsets or in
location: all locations:
-
Check nearby for one of the
common interference sources.
-
Check near the base for the
source of interference.
-
Try moving the handset away
from a suspected source, or try
moving the suspected source
so it’s not between the handset
and the base.
There is always more noise at
the edges of the base’s range.
If an Out of Range message
displays, try moving closer to
the base.
-
Try moving the base away from
a suspected source, or turn off
the source if possible.
If the base has an adjustable
antenna, try raising the antenna
so it stands straight up.
If you have any service that uses
the phone line, you might need
a filter (see below).
-
-
-
Installing a line filter or DSL filter
Sometimes, broadband Internet services that use the telephone line
can interfere with phones. One of these services−DSL−often causes
static on telephones. A DSL filter or telephone line filter usually solves
this problem. The technician who installed your DSL service might have
left some filters for you; if not, call your DSL provider or look in any
electronics store.
35
Plug the DSL filter into the telephone wall jack and plug your phone’s base
into the filter. Make a test call to make sure the noise is gone.
Do you use a T-Coil hearing aid?
-
If you have a hearing aid equipped with a telecoil (T-coil) feature, the
interaction between the hearing aid and digital cordless phones can
cause noise in the handset. If you have a T-coil hearing aid and you have
problems with noise on the line, try turning on T-coil mode. Open the
menu. Select Handset Setup, then select T-coil
.
-
Using T-coil mode can shorten the handset’s talk time; make sure to
watch the battery status and keep the battery charged.
Liquid damage
Moisture and liquid can damage your cordless phone. If the exterior
housing of the handset or base is exposed to moisture or liquid, wipe off
the liquid, and use as normal. If moisture or liquid is inside the plastic
housing (i.e. liquid can be heard in the phone or liquid has entered the
handset battery compartment or vent openings on the base), follow these
steps:
Handset
Base
-
Remove the battery cover and
disconnect the battery.
Let dry for at least 3 days with the
battery disconnected and the cover off
for ventilation.
After the handset dries, reconnect the
battery and replace the cover. Recharge
the battery fully before using.
-
Disconnect the AC
adapter to cut off the
power.
-
-
-
Disconnect the
telephone cord.
Let dry for at least
3 days before
reconnecting.
-
CAUTION! DO NOT use a microwave oven to speed up the
drying process. This will cause permanent damage to the
handset, base, and the microwave oven.
Changing from Tone to Pulse Dialing
Your phone communicates with the land line telephone network two
ways: tone dialing or pulse dialing. Most telephone companies use tone
36
dialing. If your phone company uses pulse dialing, you will need to change
your phone’s dial mode.
1. From a handset, open the menu and select Global Setup
.
2. Select Dial Mode, then select Pulse. The phone sounds a
confirmation tone.
If you use pulse dialing and you need to send DTMF tones during a call
(if you’re using an automated response system, for example), press
to temporarily switch to tone dialing. When the call ends, the phone
automatically returns to pulse dialing mode.
*
Reseꢃng and Registering Handsets
If you are having trouble with a cordless handset or if you want to replace
one, you need to clear the registration information from the base and the
handset:
Do you have the base the handset is registered to?
Yes
No
1. Press and hold End and
#
until the
1. Press and hold End and
System Reset menu appears (about 5
#
until the System Reset
seconds).
menu appears (about 5
seconds).
2. Select Base Unavailable.
2. Select Deregister HS. The display lists
all registered handsets.
3. Select the handset you want to reset.
3. When the handset asks
you to confirm, select
Yes. The handset deletes
its own link without
4. When the handset asks you to
confirm, select Yes. The handset clears
its information from the base and
deletes its own link to the base.
contacting the base.
Registering a handset
When you reset a handset (or if you buy a new one), that handset displays
a
Handset Not Registered message. If you see this message on a
handset, you need to register it to a base before you can use it.
37
Does the handset fit in the base cradle?
Yes
No
Place the handset
in the base. The
display should
say Handset
1. With the phone in standby, press and hold
find on the base for about 5 seconds.
2. On the handset you want to register, press
and hold until the display says Handset
#
Registering.
Registering (about 2 seconds).
In about 30 seconds, the handset display should say Registration
Complete. Press TaLk/fLash and make sure you get a dial tone.
If...
Try...
-
-
you don’t hear a dial tone
the display says Registration Failed
Making sure the handset is
fully charged, then starting
over at step 1.
For information on resetting and registering MULTIRANGE chargers, see
the manual that came with the MULTIRANGE handset.
AC Adapter and Baꢁery Informaꢀon
Use only the supplied AC adapters. Be sure to use the proper adapter
for the base and any chargers.
Do not place the power cord where it creates a trip hazard or where it
could become chafed and create a fire or electrical hazard.
Do not place the unit in direct sunlight or subject it to high
temperatures.
Fully charged, the battery should provide about 10 hours of talk time
and about 7 days of standby time. For best results, return the handset
to the cradle after each call to keep it fully charged.
When the battery gets too low, the handset shows a low battery alert.
If you hear a strange beep during a call, check the display: if you see
the low battery alert, finish your conversation as quickly as possible
and return the handset to the cradle. If the handset is in standby,
none of the keys will operate.
38
With normal use, the battery should last about one year. Replace the
battery when the talk time becomes short even when the battery is
charged. To buy a replacement battery, call the Parts Department
listed on the front cover.
Rechargeable Nickel-Metal-Hydride Baꢁery Warning
This equipment contains a rechargeable Nickel-Metal-Hydride
battery.
Nickel is a chemical known to the state of California to cause cancer.
Do not short-circuit the battery.
The rechargeable batteries contained in this equipment may explode
if disposed of in a fire.
Do not charge the battery used in this equipment in any charger other
than the one designed to charge this battery as specified in the owner’s
manual. Using another charger may damage the battery or cause it to
explode.
Rechargeable batteries must be recycled or disposed of properly.
Uniden works to reduce lead content in PVC coated cords in our products
and accessories.
Warning! The cords on this product and/or accessories contain
lead, a chemical known to the State of California to cause birth
defects or other reproductive harm. Wash hands after handling.
Compliance Informaꢀon
FCC Part 68 informaꢀon
This equipment complies with Part 68 of the FCC rules and the require-
ments adopted by the ACTA. On the boꢁom of this equipment is a label that
contains, among other informaꢀon, a product idenꢀꢂer in the format US:
AAAEQ##TXXXX. If requested, this number must be provided to the phone
company.
An applicable Universal Service Order Codes (USOC) cerꢀꢂcaꢀon for the jacks
used in this equipment is provided (i.e., RJ11C) in the packaging with each
piece of approved terminal equipment. A plug and jack used to connect this
equipment to the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is
39
designed to be connected to a compaꢀble modular jack that is also compliant.
See installaꢀon instrucꢀons for details.
The REN is used to determine the number of devices that may be connected
to a phone line. Excessive RENs on a phone line may result in devices not
ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed ꢂve (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the total RENs, contact the
telephone provider. The REN for this product is part of the product idenꢀꢂer
that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone
company will noꢀfy you in advance that temporary disconꢀnuance of service
may be required. But if advance noꢀce isn't pracꢀcal, the telephone company
will noꢀfy the customer as soon as possible. Also, you will be advised of your
right to ꢂle a complaint with the FCC if you believe it is necessary. The tele-
phone company may make changes in its faciliꢀes, equipment, operaꢀons or
procedures that could aꢄect the operaꢀon of the equipment. If this happens
the telephone company will provide advance noꢀce in order for you to make
necessary modiꢂcaꢀons to maintain uninterrupted service.
Please follow instrucꢀons for repairing, if any (e.g. baꢁery replacement sec-
ꢀon); otherwise do not subsꢀtute or repair any parts of the device except as
speciꢂed in this manual. Connecꢀon to party line service is subject to state
tariꢄs. Contact the state public uꢀlity commission, public service commission
or corporaꢀon commission for informaꢀon. This equipment is hearing aid
compaꢀble.
If you experience trouble with this equipment, contact the manufacturer (see
the cover of this manual for contact informaꢀon) or an authorized agent.
If the equipment is causing harm to the telephone network, the telephone
company may request that you disconnect the equipment unꢀl the problem
is resolved.
If your home has wired alarm equipment connected to a phone line, be sure
that installing the system does not disable your alarm equipment. If you have
quesꢀons about what will disable alarm equipment, contact your telephone
company or a qualiꢂed installer.
Any changes or modiꢂcaꢀons to this product not expressly approved by the
manufacturer or other party responsible for compliance could void your authority
to operate this product.
NOTICE: According to telephone company reports, AC electrical surges, typically
resulꢀng from lightning strikes, are very destrucꢀve to telephone equipment
connected to AC power sources. To minimize damage from these types of
surges, a surge arrestor is recommended.
FCC Part 15 informaꢀon
This device complies with part 15 of the FCC rules. Operaꢀon is subject to the
following two condiꢀons: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interfer-
ence that may cause undesired operaꢀon. Privacy of communicaꢀons may not
be ensured when using this phone.
fCC PArT 15.105(b): Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protecꢀon against harm-
ful interference in a residenꢀal installaꢀon. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instrucꢀons, may cause harmful interference to radio communicaꢀons.
However, there is no guarantee that interference will not occur in a parꢀcular
installaꢀon. If this equipment does cause harmful interference to radio or
television recepꢀon, which can be determined by turning the equipment oꢄ
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separaꢀon between the equipment and receiver.
Connect the equipment into an outlet on a circuit diꢄerent from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Informaꢀon
This product complies with FCC radiaꢀon exposure limits under the following
condiꢀons:
•
•
•
The base must be placed to allow a minimum of 20 cm (8 inches) between the
antenna and all persons during normal operaꢀon.
The base must not be collocated or operated in conjuncꢀon with any other
antenna or transmiꢁer.
The handset is designed for body-worn operaꢀon and meets FCC RF exposure
guidelines when used with any belt clip, carrying case, or other accessory supplied
with this product. (All necessary accessories are included in the package; any
addiꢀonal or opꢀonal accessories are not required for compliance with the guide-
lines.) Third party accessories (unless approved by the manufacturer) should be
avoided as these might not comply with FCC RF exposure guidelines.
Industry Canada (I.C.) Noꢀce
Terminal equipment
NOTICE: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Speciꢂcaꢀons. This is conꢂrmed by the registraꢀon
number. The abbreviaꢀon IC before the registraꢀon number signiꢂes that
registraꢀon was performed based on a Declaraꢀon of Conformity indicaꢀng
that Industry Canada technical speciꢂcaꢀons were met. It does not imply that
Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment
is marked on the equipment itself. The REN assigned to each terminal equip-
ment provides an indicaꢀon of the maximum number of terminals allowed to
be connected to a telephone interface. The terminaꢀon on an interface may
consist of any combinaꢀon of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Radio equipment
The term IC before the radio cerꢀꢂcaꢀon number only signiꢂes that Industry
Canada technical speciꢂcaꢀons were met. Operaꢀon is subject to the follow-
ing two condiꢀons: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause
undesired operaꢀon of the device. "Privacy of communicaꢀons may not be
ensured when using this telephone".
Warranty (Limited, 1 Year)
Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original
retail owner, this Uniden Product to be free from defects in materials and
craꢅsmanship with only the limitaꢀons or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and
be of no further eꢄect 12 months aꢅer the date of original retail sale. The
warranty is invalid if the Product is (A) damaged or not maintained as reason-
able or necessary, (B) modiꢂed, altered, or used as part of any conversion
kits, subassemblies, or any conꢂguraꢀons not sold by Uniden, (C) improperly
installed, (D) serviced or repaired by someone other than an authorized
Uniden service center for a defect or malfuncꢀon covered by this warranty, (E)
used in any conjuncꢀon with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by anyone other than
as detailed by the owner's manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to
this warranty at any ꢀme while this warranty is in eꢄect, warrantor will either,
at its opꢀon, repair or replace the defecꢀve unit and return it to you without
charge for parts, service, or any other cost (except shipping and handling) in-
curred by warrantor or its representaꢀves in connecꢀon with the performance
of this warranty. Warrantor, at its opꢀon, may replace the unit with a new or
refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND
ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE
FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow this exclusion or limitaꢀon of incidental or
consequenꢀal damages so the above limitaꢀon or exclusion may not apply to
you.
LEGAL REMEDIES: This warranty gives you speciꢂc legal rights, and you may also
have other rights which vary from state to state. This warranty is void outside
the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, aꢅer follow-
ing the instrucꢀons in the owner's manual you are certain that the Product
is defecꢀve, pack the Product carefully (preferably in its original packaging).
Disconnect the baꢁery from the Product and separately secure the baꢁery in its
own separate packaging within the shipping carton. The Product should include
all parts and accessories originally packaged with the Product. Include evidence
of original purchase and a note describing the defect that has caused you to
return it. The Product should be shipped freight prepaid, by traceable means, to
warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
As an Energy Star® Partner,Uniden has determined that this
product meets the Energy Star® guidelines for energy efficiency.
Energy Star® is a U.S. registered mark.
•
•
Uniden® is a registered trademark of Uniden America Corporaꢀon.
The pictures in this manual are for example only. Your phone may not look
exactly like the pictures.
May be covered under one or more of the following U.S. patents:
5,491,745
5,660,269
5,758,289
5,864,619
5,960,358
6,253,088
6,788,920
6,914,940
7,206,403
5,533,010
5,663,981
5,768,345
5,893,034
5,987,330
6,321,068
6,788,953
6,953,118
7,310,398
5,574,727
5,671,248
5,787,356
5,912,968
6,044,281
6,418,209
6,839,550
7,023,176
7,460,663
5,581,598
5,717,312
5,794,152
5,915,227
6,070,082
6,618,015
6,889,184
7,030,819
5,606,598
5,732,355
5,801,466
5,929,598
6,076,052
6,714,630
6,901,271
7,146,160
5,650,790
5,754,407
5,825,161
5,930,720
6,125,277
6,782,098
6,907,094
7,203,307
Other patents pending.
|