Introduction
Congratulations on your purchase of a Ultratec Special Effects LSX MKII Low Smoke Convertor. With basic care,
your LSX will provide years of trouble-free performance. The LSX is a product of many years of research and
development resulting in a machine with many fine features and exceptional reliability.
This manual contains detailed information on the operation of your LSX. Please take a few moments to read it
over carefully before use, and keep it handy for your reference.
Warning
Important Safety Instructions:
1. Do not touch, place hands or expose skin within 20” (50 cm) of the discharge nozzle.
2. Do not remove the outer case.
3. Persons suffering from asthma or allergenic sensitivity may experience irritation, discomfort or allergic
symptoms when exposed to fog effects.
4. Ensure that this unit is grounded at all times. Failure to do so may result in serious injury.
5. Use Ultratec Special Effects fluid ONLY.
Safety Precautions
1. Ensure that any operation of the machine is supervised by suitably trained and authorized personnel.
2. Do not modify the machine or use a machine which has been damaged in any way.
3. Allow sufficient air circulation around the machine at all times.
4. Protect the machine from direct weather effects and wet locations.
5. Only use fluids manufactured by Ultratec Special Effects.
6. Do not continue to produce fog when visibility is reduced to 20” 50cm or below.
7. Avoid directing fog output continuously at people, structures or objects within close proximity of the discharge
nozzle.
8. Ensure that adequate exhausting arrangements are available in the event of an emergency.
9. Do not place hands or exposed skin within the first 20” (50 cm) of the discharge nozzle at any time during fog
production.
10.Fog effects can trigger smoke alarms and detectors. Please take suitable precautions to prevent false alarms.
3
Technical Specifications
Model:
LSX Low Smoke Converter
Part Number:
CLF 2930 - 120 volt
CLF 2915 - 240 volt
Length:
59in
150cm
75cm
71cm
68kg
Width:
29.5in
28in
Height:
Net Weight:
150lbs
Power Rating:
Fluid:
120 Volt A.C. 50/60 Hz. 12 Amps.
240 Volt A.C. 50/60 Hz. 6 Amps.
Ultratec Special Effects Water Base Fog Fluid
Technical Drawings
4
Operating Procedure
1. During use this machine generates condensation. After use the LSX should be drained via the drain valve.
CAUTION: This may cause the floor to become very slippery. This may also inhibit the performance of the LSX unit.
2. This unit requires a 15 amp circuit to run properly. The use of any extension cords or shared circuit is strongly not
recommended.
3. It is essential that Ultratec Special Effects’s Genuine Molecular Fluid is used in the Fog Machine to achieve optimum
effect.
4. The LSX unit is controlled by a user-friendly panel. When the system switch is in the ‘On’ position and illuminated,
power is established to the LSX unit. A ‘green led’ is provided to indicate the compressor is operating.
5. An Automatic Reset Low Pressure Switch is provided as protection against compressor damage. If the Low Pressure
Switch has been activated the ‘Red’ LED will illuminate (the ‘Green’ LED will not be illuminated).
6. The Variable Fan Control regulates Fog Density Output. Some experimenting will produce various effects. An OFF
position is provided on this control. It is not recommended that this control be left in the off position as this will
eventually result in activation of the Low Pressure Switch and cause a freeze up condition.
Control Panel Operations
1. Fan Knob: this controls the speed of the lower fan.
Turning clockwise reduces the speed. Off is at the
counter clockwise end.
Note: It is not recommended to leave the control left
in the ‘Off’ position or in a very low setting, the low
pressure switch may activate turning off the compressor.
2. Low Pressure Light: when lit, indicates that Low Pressure
1
2
3
Protection has been activated. The Low Pressure Switch
will automatically reset but may take 2 - 3 cycles to start,
unless a leak has occurred in the system.
3. Compressor Light: compressor is operating normal when
lit.
4. Power Switch: power is on when lit.
Note: A cooler ambient temperature may result in
activation of Low Pressure Switch within a short period
of time after initial start up. To remedy this problem the
unit can be stored in a warm location, a “load” can be
put on the cooling chamber by introducing warm fog
into the unit just after start up, or by simply covering the
top of the unit to stop air flow.
4
5
Before Requesting Service
If LSX will not Power Up
Check Power source and connections
Green ‘LED’ is not illuminated & Red ‘LED’ is
illuminated
Low Pressure Switch has tripped, allow for Auto Reset
Low Pressure Switch will not Auto Rest. Red ‘LED’ Low Refridgerant Charge (Contact Local Dealer)
remains illuminated
Fog will not remain on ground
1. Ensure the use of Ultratec Special Effects Fluid
2. Check digital temperature display reading for coil
temperature
3. Check Green and Red ‘LED’ see above
Green ‘LED’ goes out when unit is operating and
Red ‘LED’ doesn’t illuminate
Check Power Source for sufficient voltage. Do NOT use
extension cords.
Condensation on floor / Floor seems slippery
4. Too much fog going through LSX
5. Fog machine nozzel is too close to LSX
6. Reduce fog output, or duration
Recommended Fluids
Molecular Fog Fluid: A faster dissipation versus the Director’s Choice Fog Fluid. This thick, clean, white fog is an
optimal solution for a dense low-lying fog effect when chilled with the LSG or LSX machines.
Maintenance Fluid
EZ Kleen Preventative Maintenance Fluid: Using EZ Kleen preventative maintenance fluid on a regular basis ensures
longer life for the heat exchanger in Ultratec fog machines by reducing blockage.
All of our Fog Fluids are water based. Damage will occur if Haze Fluid is used.
6
Warranty
Warranty:
All warranty is for one year parts and labour unless specified or manufacturer defect only.
Abuse or Poor Maintenance will not be covered under warranty. Ultratec Special Effects Fluids
must always be used. Use of any non Ultratec Special Effects Fluids will void all warranties.
Accept no substitutions as there are no exceptions to this rule. Proof of Purchase or Proof of
Sale must always accompany any warranty returns. An RA (return authorization) number must
be noted on the outside of the box being returned to our facilities. Any packages without
a clearly marked RA number will not be accepted by our receiving department. Freight on
warranty items are freight prepaid to our facility and we will prepay freight back to your facility
after repair by the most economical means available. Should you require the item express-
returned, then you are responsible for any difference in freight cost.
Return Policy:
Return of any product must be done within 30 days of purchase. The package must be
returned freight prepaid and the RA number clearly marked on the outside of the box.
Minimum restocking fee is 25%. Once our facility has received the product a technical
assessment will be completed to determine if an additional restocking fee needs to be issued.
Only credits are issued to the dealers account. Any product not returned within 30 days is
considered purchased.
Warning:
Ultratec Special Effects Inc. considers all of it’s product to be safe for use in the application it
was intended. Ultratec Special Effects takes no responsibility for misuse or incorrect use. Always
refer to the Product Manual for proper use.
Contact Information
Head Office
Canadian Shipping Address
USA Shipping Address
(For All USA Repairs)
Ultratec Special Effects Inc.
640 Gadson St.
Ultratec Special Effects Inc.
1960 Blue Heron Drive
London, Ontario N6H 5L9
(For All Canadian Repairs)
Ultratec Special Effects Inc.
1960 Blue Heron Drive
London, Ontario N6H 5L9
Groveland, Florida 34736
Direct: 519-659-7972
Toll Free: 866-534-5557
Fax: 519-659-7713
Please remember to include the RA Number on all items being shipped for
repairs.
and then click on “Master Service Tracker or contact service at 519-951-3357 /
866.534.5557
7
|