MODEL SF-680
Digital Fabric Steam Press
by Top Innovations, Inc.
Please read all instructions before use.
Mail in your warranty registration card.
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of fire, electrical shock, or injury,
the following basic safety precautions should always be followed
when using an electrical appliance.
READ ALL INSTRUCTIONS BEFORE USING YOUR STEAM PRESS
1. DO NOT leave your SF-680 Digital Fabric Steam Press unattended when plugged
in or not in use.
2.
This unit is not a toy. Close supervision is required when using unit
near children, pets, and plants. Unit produces steam that is hot and
pressurized. Care must be taken to avoid burns or other injuries.
3. Always unplug electrical cord when unit is not in use. DO NOT use this unit if
electrical cord or outlet is damaged. DO NOT use unit if it is not working
properly or has been dropped, damaged, or left outdoors. If such damage occurs,
return unit to a licensed service technician for repairs.
4. This unit is an electrical appliance. DO NOT submerge it in water. DO NOT use
electrical cord as a handle. DO NOT allow cord to be crimped by closing it in
doors. DO NOT pull or stretch cord around sharp corners or edges. Be sure to
keep electrical cord away from all heated surfaces.
5. DO NOT use this unit with extension cords or electrical outlets that have
inadequate current capacity. A three-prong outlet or a properly grounded adapter
is necessary when using SF-680 Digital Fabric Steam Press.
6. In order to unplug SF-680 Digital Fabric Steam Press, grasp plug and pull
smoothly and firmly from outlet. DO NOT attempt to unplug unit by pulling or
tugging on cord.
7. Use caution when operating unit, as burns can occur from touching hot metal
parts, or from close proximity to steam.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Top Innovations, Inc.
3
IMPORTANT SAFEGUARDS
WARNING: To reduce the risk of electric shock, this appliance
has a three-pronged plug. This plug will fit in a polarized wall
outlet only one way. If the plug does not fit fully in the outlet,
contact a licensed electrician to install a proper outlet. DO NOT
attempt to modify the plug or defeat this safety feature.
8. DO NOT handle or use this unit while hands are wet or when not wearing shoes.
To avoid falls and other injuries, be sure to dry any wet areas on floors and to
stand away from damp surfaces while using steam press.
9. SF-680 Digital Fabric Steam Press is only meant to be used with recommended
SF-680 accessories. Other types of accessories are not to be used with
Digital Fabric Steam Press. Doing so may cause injuries or damage to unit.
10. Surfaces become hot during use. To avoid injuries, DO NOT touch Pressing
Plate or any other surface while using this appliance. DO NOT place arms or
hands between Pressing Plate and Ironing Board while unit is in operation.
11. When filling your Digital Fabric Steam Press with distilled water, DO NOT fill
Water Reservoir past MAX (300 ml) line.
12. Before filling unit with water, always take the following steps:
(1) Turn appliance off
(2) Unplug electrical cord
Failure to follow these steps may result in electric shock and injury.
13. Only water should be used in unit. Other cleaning agents will damage unit and
can cause injuries.
14. DO NOT operate unit if steam openings are blocked. Should this occur, shut
unit off and unplug.
15. Store your SF-680 Digital Fabric Steam Press in a cool, dry place. Always
allow unit to cool completely before storing.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Top Innovations, Inc.
4
DIGITAL FABRIC STEAM PRESS PRODUCT
INFORMATION
The following features and accessories are included with your steam press. Carefully inspect
packaging material as some parts are shipped inside Styrofoam packaging. To obtain
possible missing parts, refer to the Customer Support section on page 10 of this manual.
UNIT FEATURES AND ACCESSORIES
1. Handle
2. Steam Burst Buttons
3a. Water Reservoir Cap
3b. Water Reservoir
4. Ironing Board
5. Pressing Plate
6. Pressing Plate Cover
7. On/Off Switch
8. Locking Knob
9. Power Indicator Light (Red)
10. Pressing Indicator Light (Green)
11. Steam Burst Ready Indicator
Light (Yellow)
12. Temperature Control Buttons
13. Cord Storage Compartment
14. Measuring Cup
15. Spray Bottle
16. Pressing Cushion
Top Innovations, Inc.
5
DIGITAL FABRIC STEAM PRESS PRODUCT
INFORMATION
- The Handle (1) is used to safely lift up and lower the Pressing Plate, and carry the
unit.
- The Steam Burst Buttons (2) are located on either side of the Handle, and
produce a powerful burst of steam when pressed.
- The Water Reservoir Cap (3a) covers the Water Reservoir fill hole and must be
removed in order to fill the Water Reservoir with distilled water.
- The Water Reservoir (3b) is the tank in which distilled water is stored for use by
the unit. There must be water in the Water Reservoir in order for the units steam
burst function to work correctly.
- The Ironing Board (4) is the padded surface onto which fabric is placed during
pressing. The fabric cover is removable and can be washed.
- The Pressing Plate (5) is the temperature-controlled teflon surface that heats and
presses fabric.
- The Pressing Plate Cover (6) is the stainless-steel cover that protects the Pressing
Plate.
- The On/Off Switch (7) activates and deactivates the unit.
- The Locking Knob (8) locks the Pressing Plate and Ironing Board together. This
allows for carrying and storage of the unit.
- The Power Indicator Light (Red) (9) illuminates when the On/Off Switch is set to
the “On” position, providing you with a clear visual indication that the unit is
powered on.
- The Pressing Indicator Light (Green) (10) illuminates while the unit is heating to
the selected temperature. When deactivated, this indicates that you are ready to
press.
- The Steam Burst Ready Indicator Light (Yellow) (11) illuminates once the unit is
ready to produce bursts of steam, providing you with a clear visual indication that
you can begin using the Steam Burst Buttons.
- The Temperature Control Buttons (12) are pushed to select a desired temperature.
Press the right arrow button to cycle right through the list of fabric choices above
the buttons, and press the left arrow button to cycle left through the list of fabric
choices above the buttons.
- The Cord Storage Compartment (13) provides a convenient and easily accessible
place to store the power cord.
- The Measuring Cup (14) is designed to assist you in easily filling the Water
Reservoir with distilled water.
- The Spray Bottle (15) allows you to moisten fabrics before pressing, which helps
to make the pressing process easier and more effective in certain instances.
- The Pressing Cushion (16) is a fabric-covered pad used for pressing gathered or
contoured areas such as sleeves, darts, or yokes.
Top Innovations, Inc.
6
USING THE DIGITAL FABRIC STEAM PRESS
FILLING WATER RESERVOIR
1. Place Digital Fabric Steam Press on a flat, level surface.
2. Turn Locking Knob to “Unlock” position to unlock Pressing Plate.
3. Lift up Pressing Plate using Handle. It will automatically stay in lifted position.
4. Pull Water Reservoir out. Note that Water Reservoir cannot be completely
removed from unit; do not attempt to force it free.
5. Remove Water Reservoir Cap to expose Water Reservoir fill hole.
6. Using Measuring Cup (included), fill Water Reservoir up to the MAX (300 ml)
line with distilled water.
7. Replace Water Reservoir Cap and push filled Water Reservoir back into main
unit.
OPERATING DIGITAL FABRIC STEAM PRESS
1. Plug power cord into electrical outlet, and set
On/Off Switch to “On” position (FIGURE 1).
2. Identify type of fabric you are going to press,
and select corresponding temperature setting
using Temperature Control Buttons. Note that it
is best to start with the most delicate fabrics
first, as higher levels of heat will cause damage
to Nylon and Silk.
3. Lay fabric flat on Ironing Board.
4. Digital Fabric Steam Press is ready for use when
Pressing Indicator Light deactivates. If pressing
FIGURE 1
wool, you may choose to spray with a burst of
steam. This function is available once Steam
Burst Ready Indicator Light illuminates.
NOTE: Do not activate burst of steam with unit completely closed, as this may
damage unit. Best results are obtained if Pressing Plate is held open approxi-
mately 75 mm above Ironing Board before pressing Steam Burst Button. For
safety reasons, do not hold Pressing Plate open more than 75 mm when using
steam burst function.
5. To press, lower Pressing Plate gently onto fabric and Ironing Board. Hold there
for 8-10 seconds, then lift up Pressing Plate. Repeat until you have achieved
desired crease and smoothness.
6. Once pressing tasks are complete, immediately set On/Off Switch to “Off”
position. Refer to page 9 of this manual for further information about cleaning
and storage of Digital Fabric Steam Press.
Top Innovations, Inc.
7
USING THE DIGITAL FABRIC STEAM PRESS
STEAM BURST
1. Hold Pressing Plate approximately 3” above Ironing Board.
2. Press Steam Burst Button to release a burst of steam onto fabric.
3. Lower Pressing Plate onto fabric, then raise once again.
4. Repeat steps 1-3 above until fabric is smooth and wrinkle-free.
PRESSING AND STEAMING TIPS
Pressing Shirts and Blouses
1. Place shoulder yoke on Ironing Board first and press.
2. Next, place sleeves onto Ironing Board with fold parallel to long seam and press.
3. Place cuffs onto end of Ironing Board and press.
4. Place bottom of shirt behind Ironing Board. Begin by pressing the side with
pocket. Pull shirt towards you as you press each section.
5. Finish by pressing collar of shirt.
Pressing Pants
1. Place Pressing Cushion under waistband and press, repositioning waistband until
completely pressed.
2. To press inseam, place Pressing Cushion under area to be pressed.
3. Place pleated area on Ironing Board. Carefully fold pleats and press.
4. Embroidery should be placed face down on Ironing Board to reduce wear and
prevent damage to delicate areas.
Other Techniques
- Placing Pressing Cushion between fabric and Pressing Plate may help with
delicate fabrics.
- Buttons and zippers. If you have older types of buttons or zippers, you may need
to take special care to avoid melting. In order to do so, place garment face-down
and cover with Pressing Cushion before pressing.
- Spray Bottle may be used to spray fabrics lightly. This will further help to remove
exceptionally stubborn wrinkles.
- Place a damp cloth over fabric before pressing, which will help with stubborn
wrinkles or heavy gauge fabrics.
- To press large pieces of fabric, place entire piece behind Ironing Board. Pull
fabric towards you, over Ironing Board, and lower Pressing Plate. Press fabric in
sections until completed.
Top Innovations, Inc.
8
CARE AND STORAGE GUIDELINES
AUTO SHUT-OFF
The Auto Shut-Off feature of the Digital Fabric Steam Press includes both an
Auto Shut-Off and an Auto Wake-Up. These multiple function safety features
deactivate electrical power to the heater when the Pressing Plate has been left in
closed position against the Ironing Board for more than 10 seconds. Heater
deactivation is signaled by a beeping sound. Heater functionality is restored
when the Pressing Plate is lifted back up.
Power to the heater will also be cut if the Pressing Plate is left in the lifted
position without use for approximately 15 minutes (signaled by a beeping sound
for approximately 22 seconds). After the beeping sound has stopped, the heating
ability of the unit can only be restored in by pressing the Temperature Control
Buttons.
IMPORTANT: Auto Shut-Off does not mean that power to the unit is
totally cut off. Power is always on, and the Power Indicator Light will
remain illuminated until On/Off Switch is set to “Off” position.
CLEANING THE DIGITAL FABRIC STEAM PRESS
1. Place Pressing Cushion in the middle of Ironing Board.
2. Place a clean towel over Pressing Cushion and Ironing Board.
3. Set Temperature Control Buttons to the highest setting (LINEN).
4. When Steam Burst Ready Indicator Light illuminates, lower Pressing Plate
onto Pressing Cushion.
5. Press Steam Burst Button six times.
6. Allow Pressing Plate to cool.
7. Clean Pressing Plate with damp cloth. Do not use abrasive materials, as this
may damage Pressing Plate.
8. Ironing Board fabric cover is removable for cleaning. Hand wash only with
mild detergent.
PROPER STORAGE
1. Once pressing is complete, immediately turn unit off and unplug power cord
from electrical outlet.
2. Allow unit to cool completely (at least 30 minutes).
3. Lower Pressing Plate down, and turn Locking Knob to “Lock” position.
4. Wrap up power cord and place in Cord Storage Compartment.
5. Store all accessories safely away, preferably near Digital Fabric Steam Press.
6. Store Digital Fabric Steam Press in a cool, dry place.
Top Innovations, Inc.
9
CUSTOMER SUPPORT
SOLUTION
PROBLEM
POSSIBLE CAUSE
Unit fails to steam. Power
Indicator Light does not
illuminate.
Unit is not plugged in.
Plug into electrical
outlet.
Household Circuit Breaker /
Ground Fault Interrupter has
tripped or blown a fuse.
Reset Circuit Breaker /
Ground Fault Interrupter, or
replace fuse. If you need
assistance, contact a licensed
electrician.
Auto Shut-Off has engaged.
Water Reservoir is empty.
Refer to Auto Shut-Off
section on page 9 of this
manual for proper
procedure.
Unit fails to steam. Power
Indicator Light does
illuminate.
Refill Water Reservoir using
procedures on page 7 of this
manual.
Unit is damaged or
malfunctioning.
Please contact our customer
support department.
Steam Burst output is weak
or intermittent.
Pressing Plate needs to be
cleaned.
Refer to Cleaning the
Digital Fabric Steam Press
section on page 9 of this
manual for proper procedure.
CUSTOMER SUPPORT
For problems with your steamer, please refer to the Troubleshooting Guide located
above. Additional inquiries should be directed to our Customer Support services at
(800) 711-6617 or (816) 584-9700 ext. 102 or 130, or e-mailed to:
Top Innovations, Inc.
10
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
(If outside USA, additional shipping charges may apply)
Top Innovations, Inc. warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. This warranty
does not cover damage caused by misuse, negligence, use by improper current or
voltage, use contrary to operating instructions or disassembly, repair or alteration
by any person other than Top Innovations, Inc. Warranty Service Department.
Top Innovations, Inc. will repair or replace, at its option. This warranty gives you
specific legal rights and may have other rights, which may vary from state to state.
Performance of any obligation under this warranty may be obtained by:
1. Call (800) 711-6617 or (816) 584-9700 for Return Authorization Number
before returning for repair. Failure to obtain a Return Authorization Number
will cause a delay in warranty and out-of-warranty service requests.
2. Include copy of purchase receipt.
3. Include your name, address, telephone number, and Return Authorization
Number on returned package.
Please send product postage-prepaid to:
TOP INNOVATIONS, INC.
WARRANTY SERVICE DEPARTMENT
400 N.W. PLATTE VALLEY DR.
RIVERSIDE, MO 64150
Should there be any missing or defective parts or accessories, please contact
Customer Support. In most cases, it is not necessary to return the entire unit. We
can ship most parts directly to your door.
Upon expiration of 1 year limited warranty, you will be advised of the repair cost
before any services are performed. However, you may enclose a note indicating
that you would like us to proceed with repairs without first notifying you.
If you have any questions about coverage under this warranty, you may contact the
Warranty Service Department by telephone at (800) 711-6617 or (816) 584-9700
ext. 102 or 130, or e-mail [email protected].
Top Innovations, Inc.
11
Top Innovations, Inc.
400 N.W. Platte Valley Dr.
Riverside, MO 64150
Tel: (800) 711-6617
(816) 584-9700
Printed in China
V040415
|