TC14A/TC18A
Domestic and Std. Export
English
P/N 39289
Rev. E • V1 • 5/00
Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • (847)741-3300 • FAX (847)741-4406
Conveyor Toaster
Models TC14A, TC18A
OWNER'SOPERATINGANDINSTALLATION
MANUAL
© 2000 Toastmaster, A Middleby Company.
is a registered trademark of Toastmaster, A Middleby Company. All rights reserved.
I. DESCRIPTION AND SPECIFICATIONS
A. Component Location
WARNING: IN CASE OF FIRE
Disconnect the toaster from its power source IMMEDI-
ATELY. This allows the unit to cool, making it easier to
put out the fire.
The major components of the toaster are shown in Figure 1 below.
Figure 1
WARNING
FOR YOUR SAFETY DO NOT STORE OR USE GASO-
LINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS
IN THE VICINITY OF THIS OR ANY OTHER APPLI-
ANCE
4. Entry rack
5. Conveyor
3. Crumb tray
WARNING
IMPROPER INSTALLATION, ADJUSTMENT, ALTER-
ATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ
THE INSTALLATION AND OPERATING INSTRUC-
TIONS THOROUGHLY BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT.
2. Conveyor speed
control knob
1. Product
selection knob
6. Return tray
WARNING
DO NOT OPERATE THE CONVEYOR TOASTER ON
EITHER OF ITS SIDES, ON ITS REAR SURFACE, OR
WITHOUT LEGS. PREMATURE FAILURE OF THE
HEATING ELEMENTS WILL OCCUR.
B. Component Function (see Figure 1)
1-2. Toaster control knobs - see Section III, Operation.
3. Crumb tray - Collects crumbs from the toasted product. The tray
can be removed for cleaning.
WARNING
4. Entry rack - Loaded with the bakery product to be toasted. The
product then slides onto the conveyor. The entry rack can be
removed for cleaning.
DISCONNECT THE TOASTER FROM ITS ELECTRICAL
POWERSUPPLYBEFORECLEANINGORSERVICING.
CAUTION
5. Conveyor - Transports the bakery product through the toaster,
between the top and bottom heating elements.
Using any parts other than genuine Toastmaster factory parts relieves
the manufacturer of all liability.
6. Return tray - Collects the toasted product. The tray can be removed
for cleaning.
IMPORTANT
Contact your authorized service agent to perform maintenance and
C. Operating and Electrical Specifications
Pre-Heat Time: 20 minutes
repairs. A service agency directory is supplied with your toaster.
IMPORTANT
Toastmaster (manufacturer) reserves the right to change specifica-
tions and product design without notice. Such revisions do not entitle
the buyer to corresponding changes, improvements, additions or
replacements for previously purchased equipment.
Electrical Specifications/TC14A toaster models:
•
•
•
TC14A74. 120V, 50/60 Hz, 1 Ph, 1.7kW, 14.3A, NEMA 5-20P plug.
TC14A63. 208V, 50/60 Hz, 1 Ph, 1.8kW, 8.6A, NEMA 6-15P plug.
TC14A66. 240V, 50/60 Hz, 1 Ph, 1.8kW, 7.5A, NEMA 6-15P plug.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
This manual provides detailed information for the installation and
operation of your toaster. It also contains information to assist the
operator in diagnosing problems in the event of a malfunction. This
manual is an important tool for the operator and should be kept readily
available.
Electrical Specifications/TC18A toaster models:
•
•
TC18A63. 208V, 50/60 Hz, 1 Ph, 2.2kW, 10.5A, NEMA 6-20P plug.
TC18A66. 240V, 50/60 Hz, 1 Ph, 2.2kW, 9.1A, NEMA 6-20P plug.
NOTE
Electrical wiring diagrams are provided at the back of this Manual.
B. Operation Procedure
C. Shutdown Procedure
1. Restore electrical power to the toaster at the circuit breaker/fused
disconnect.
1. Switch the Product Selection knob to the OFF (“O”) position.
2. Disconnect electrical power to the toaster at the circuit breaker/
fused disconnect.
2. Switch the Product Selection knob to either TOAST (
) or BUNS/
3. Allow the toaster to cool.
BAGELS ( ), depending on the product to be toasted.
D. Clearing Jams
3. Allow the toaster to pre-heat for at least 20 minutes.
WARNING
4. Adjust the toasting time (if necessary) by turning the conveyor speed
control knob.
NEVER INSERT YOUR HANDS INTO THE TOASTING CHAM-
BER TO CLEAR A JAM. SERIOUS INJURY MAY RESULT.
5. Load the entry rack with the bakery product to be toasted. The
product will slide off the entry rack and onto the conveyor.
CAUTION
NEVER use a plastic object to clear a jam. If the toaster is not com-
IMPORTANT
pletely cool, damage to the toaster may result.
If the Product Selection knob is set to BUNS/BAGELS (
), load
CAUTION
the bakery product CUT SIDE DOWN for proper toasting. Refer to
Figure 5.
When clearing a jam, use care to avoid damaging the heating elements.
1. Switch the Product Selection knob to the OFF (“O”) position.
6. After toasting, remove the product from the return tray.
2. Disconnect electrical power to the toaster at the circuit breaker/
fused disconnect.
7. During inactive periods, switch the Product Selection knob to the
3. Allow the toaster to cool.
BUNS/BAGELS (
) position. This leaves only the lower heating
CAUTION - HOT SURFACES
DO NOT ATTEMPT TO CLEAR THE JAM UNTIL THE TOASTER
HAS COOLED THOROUGHLY.
elements on, allowing a quicker recovery to normal toasting
temperatures.
4. Carefully clear the jam using a long object as a probe. This object
should preferably be made of wood, which is less likely to damage
the heating elements.
Figure 5
Product selection
knob in “BUNS/
BAGELS” position
E. Daily Cleaning
WARNING
WHEN CLEANING THE TOASTER, NEVER APPLY ENOUGH
LIQUID TO STAND IN PLACE ON THE UNIT. DO NOT SPRAY,
RINSE, OR SUBMERGE THE TOASTER. EXCESSIVE MOIS-
TURE IN THE UNIT WILL CAUSE A SEVERE ELECTRICAL
HAZARD AND MAY OTHERWISE DAMAGE THE TOASTER.
CAUTION
DO NOT clean your toaster using abrasive cleaners or pads. Both will
scratch and dull the finish.
Load buns/bagels
CUT SIDE DOWN
for proper toasting
1. With the conveyor running, use a brush to clean any crumbs off the
conveyor into the crumb tray.
2. Switch the Product Selection knob to the OFF (“O”) position.
3. Disconnect electrical power to the toaster at the circuit breaker/
fused disconnect.
4. Allow the toaster to cool.
CAUTION - HOT SURFACES
DO NOT TOUCH HOT SURFACES ON THE TOASTER, OR
REACH INTO THE TOASTING CHAMBER, UNTIL THE UNIT
HAS COOLED THOROUGHLY.
5. Wipe the exterior of the toaster with a sponge or cloth soaked in hot
or warm detergent water. Wipe with a clean, damp cloth to remove
the excess detergent, and then wipe again to dry the toaster.
6. Remove the crumb tray and the return tray from the toaster, and
empty them. Wash the trays in warm detergent water, and rinse
them.
CAUTION
Never remove the crumb tray while the conveyor is moving.
7. Remove the entry rack from the toaster. Wash the rack in warm
detergent water, and rinse it.
8. Towel the trays and entry rack dry. Reassemble all parts onto the
toaster.
Wiring Diagram
Model TC14A74
120V Toasters
TOP ELEMENT
BTM ELEMENT 1
BTM ELEMENT 2
FAN
MOTOR
CONVEYOR
SPEED CONTROL
PRODUCT
SELECTION
SWITCH
TERMINAL
BLOCK
GND
Wiring Diagram
Model TC14A63, -66
208V and 240V
Toasters
TOP ELEMENT
BTM ELEMENT 1
BTM ELEMENT 2
FAN
MOTOR
TRANSFORMER
230V p
PRODUCT
115V s
CONVEYOR
SPEED CONTROL
SELECTION
SWITCH
TERMINAL
BLOCK
GND
Wiring Diagram
Model TC18A63, -66
208V and 240V
Toasters
TOP ELEMENT 1
TOP ELEMENT 2
BTM ELEMENT 1
BTM ELEMENT 2
FAN
MOTOR
TRANSFORMER
230V p
PRODUCT
SELECTION
SWITCH
115V s
CONVEYOR
SPEED CONTROL
TERMINAL
BLOCK
GND
Switch
Configuration
All Model TC14A
and TC18A Toasters
BUNS/
BAGELS
OFF
TOAST
A Middleby Company
Toastmaster • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406
Middleby Corp 24-Hour Service Hotline 1-800-238-8444
|