Tivoli Audio Clock Radio Dual Alarm Speaker User Manual

OWNER’S MANUAL  
Dual Alarm Speaker  
voli Audio  
Ti  
12  
1
11  
10  
2
4
9
3
8
5
7
6
 
11) Use only with the cart, stand, tripod, bracket, or table specified by the  
manufacturer, or sold with the apparatus. When a cart is used, use  
caution when moving the cart/apparatus combination to avoid injury  
from tip-over.  
12) Unplug this apparatus during lightning storms or when unused for long periods of time.  
13) Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as if the power-supply cord or plug  
is damaged, liquid has been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not operate normally, or  
has been dropped.  
14) Operate this product only from the type of power source indicated on the rear  
panel. For products using an external power supply, use an exact replacement if  
lost or damaged. For products operating from battery power, refer to the user manual.  
15) Unplug this product from the wall outlet and refer servicing to qualified service  
personnel under the following conditions:  
a. When the power supply cord or plug is damaged.  
b. If liquid has been spilled or objects have fallen into the product.  
c. If the product has been exposed to water or rain.  
d. If the product does not operate normally by following the operating instructions.  
e. If the product has been dropped or damaged in any way.  
f.  
When the product exhibits a distinctive change in performance.  
16) When replacement parts are required, be sure the service technician has used  
replacement parts specified by the manufacturer.  
17) Upon completion of any service, ask the service technician to perform safety  
checks to confirm the product is in proper operating condition.  
18) This product has been tested and found to comply with the limits for Part 15 of  
the FCC rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This product generates, uses, and  
can radiate radio frequency energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference with radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the product on and off, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
- Reorient or relocate the receiving antennas  
- Increase the separation between the equipment and the receiver.  
- Connect the equipment to an outlet on a circuit different from that to which the  
receiver is connected.  
3
 
19) For added protection for this product during a lightning storm, or when it is left  
unattended and unused for long periods of time, unplug it from the wall outlet and  
disconnect the antenna or cable system. This will prevent damage to the product  
to lightning and power-line surges.  
20) Keep this product a safe distance away from naked flame, such as a lit candle.  
21) Do not expose this product to splashing or dripping. Objects containing liquid,  
such as vases or drinking glasses, should not be placed on top of this product.  
22 The recommended operating temperature range is 5 degrees C to 40 degrees C.  
23) The 12VDC input is suited for operating this product in a boat or camper using an  
optional 12VDC, 2A fused adapter.  
4
 
About Tivoli Audio  
Tivoli Audio was started by Tom DeVesto with the goal of bringing simple to use, high  
quality audio products to the consumer at reasonable prices. His long professional  
association with Henry Kloss includes co-founding Cambridge SoundWorks*. As CEO  
and head of research and development at his former company, Tom was responsible  
for the development of many of the best selling home entertainment and multi-media  
products on the market. He also held senior management positions in product development  
at both Advent and Kloss Video.  
*Cambridge SoundWorks is a registered trademark of Creative Labs, Singapore.  
Dual Alarm Instructions  
Congratulations on your purchase of the Dual Alarm Speaker. With the additional Dual  
Alarm Speaker connected, you will enjoy stereo sound and have a second alarm option.  
In order to take full advantage of what your new Dual Alarm Speaker is capable of,  
please take a moment to fully read this owner’s manual. If you have any questions,  
do not hesitate to contact your dealer or Tivoli Audio directly.  
Please save the carton and original packing should you ever need to ship your  
radio, as shipping damage is not covered by the factory warranty.  
On behalf of all of us, thank you for choosing Tivoli Audio!  
Packed with your Dual Alarm Speaker you should find:  
• 1 External Power Supply  
• 1 AA/UM-3 Alkaline Battery  
• 1 Warranty Registration Card  
Please contact your dealer or Tivoli Audio if any of these items are missing.  
Getting Started  
1. Connect the Dual Alarm Speaker’s audio cable to the Model Three’s rear “R-SPR”  
RCA output.  
2. Set the Model Three’s rear Mono/Stereo Switch to the “Stereo” position.  
3. Set the Model Three’s rear Balance Control to the center detent position.  
4. Plug the included power supply into the rear Power jack on the Dual Alarm Speaker.  
5. Adjust the Model Three’s volume level to the desired position.  
6. Install the included battery in the Dual Alarm Speaker and set the time using the  
Time Set button  
5
 
Guide To Features (Front Panel)  
1. ALARM: Once you have set the wake-up time using the Alarm Thumbwheel, push  
this button in to activate the alarm and the corresponding green LED will light. The  
LED will remain lit until the Alarm button is turned off. Push the Alarm button out to  
deactivate the alarm and the LED will extinguish. This Alarm button controls the  
Dual Alarm Speaker only and has no affect on the Model Three clock radio’s alarm,  
and vise-versa. See “How to set the alarm” for more information.  
2. ALARM THUMBWHEEL: Rotate the aluminum thumbwheel counterclockwise  
until the Alarm hand points to the designated time you wish to wake to. Do NOT  
turn the Thumbwheel clockwise or you may damage the mechanism. See  
“How to set the Alarm” for more information.  
3. SNOOZE (Top of Cabinet): When the Alarm sounds, press, hold, and then release  
the Snooze button to silence the Alarm for approximately 5 minutes. After 5 minutes,  
the alarm will automatically resume. This Snooze button controls the Dual Alarm  
Speaker only and has no affect on the Model Three clock radio’s alarm or radio.  
Likewise, the Model Three’s Snooze button will not affect the Dual Alarm Speaker’s  
alarm tone. The snooze time is not adjustable.  
4. CLOCK: This quartz analog clock features a fine mechanical quartz movement  
for superb accuracy. The clock operates off of a single “AA” battery so power  
failures will not affect the clock’s accuracy. Check the battery annually so the  
clock remains accurate. The clock’s illumination cannot be turned off or adjusted.  
It is normal for the light to take take several seconds to extinguish if the power  
supply is disconnected.  
6
 
Guide To Features (Rear Panel)  
1. CONNECTING CABLE: Connect the male RCA from this cable to the Model Three  
clock radio’s rear female RCA output marked “R-SPR” and switch to Stereo. Set  
the Model Three’s rear Balance Control to the center detent position for equal balance  
between the two speakers. Connecting a speaker other than the Tivoli Audio Dual  
Alarm or Stereo Speaker will void your warranty and possibly damage your unit.  
2. 12VDC, 10mA: Connect the included AC power supply to this input. Use only the  
power supply provided with this product. To obtain a replacement,  
contact your authorized dealer or Tivoli Audio, USA: 1.877.297.9479.  
The power supply connector is 5.5mm/2.1mm x 13mm long, center  
positive. Do not connect the power supply to an electrical outlet  
controlled by a wall switch. It is normal for the power supply to become warm during  
use. An optional 12VDC nominal, 1.5A fused source may also be used.  
3. TIME SET: Briefly press and release this button to advance the hands in small  
increments. Press and hold this button to continuously advance the clock’s hands.  
Release the button when the clock is set properly. Be sure the alarm button is in  
the Off position when setting the time. See “How to set the clock”.  
4. ALARM GRILLE: The alarm beep emits from this grille. Do not block this grille.  
5. BATTERY BACK UP: Remove the battery cover and install a fresh major brand 1.5V  
“AA” battery, observing correct +/– polarity. The clock operates off of  
the battery continuously and the battery also acts as a back up. In the  
event of a power failure, the battery back up will maintain the clock’s  
operation and sound the wake-up tone if the alarm button is in the On  
position, provided a fresh battery is correctly installed. The clock face will not illuminate  
and the radio will not operate during a power failure in order to conserve battery  
life. Check the battery’s strength annually and replace only with a major brand,  
1.5V “AA” alkaline battery. If the clock stops operating, replace the battery. To  
reduce the risk of fire or injury, do not leave a dead battery in the clock. Do not  
dispose of the spent battery into a fire. Do not open or tamper with the battery. Do  
not recharge the supplied battery. Dispose of the spent battery according to your  
state/country's regulations. Remove the battery if the Dual Alarm is to be stored or  
unused for a long period of time.  
7
 
How To Set The Clock  
Set the hands to the correct time with the Time Set button. Push the Time Set button in  
and release to move the hands in small increments or hold the button in to continuously  
advance the hands. Be sure the front panel alarm button is in the OFF position when  
adjusting the time.  
How To Set The Alarm  
1. Rotate the alarm thumbwheel counter-clockwise and set the alarm hand to the  
approximate time you wish to wake to. DO NOT TURN THE ALARM BEZEL  
CLOCKWISE OR YOU MAY DAMAGE THE MECHANISM.  
2. Press the Alarm button ON and the green alarm LED will light. The alarm tone activate  
when the clock time roughly coincides with the setting of the alarm hand.  
3. To turn the Alarm OFF, press the Alarm button again and the Alarm LED will extinguish.  
The Dual Alarm Speaker can be set to wake to the alarm tone only.  
Important Note: Due to the nature of the alarm thumbwheel’s analog mechanism,  
which was designed for simplicity, there can be up to a five-minute deviation from  
when the alarm activates. For example, if the alarm is set for 10:00, it is possible it  
could activate at 9:55 or 10:05. We recommend you set the alarm early the first  
time you use it to accommodate for this. As you use your Dual Alarm Speaker you  
will get a better idea of where you need to set the alarm in order to wake-up  
at the desired time.  
8
 
Placement  
Placing your Dual Alarm Speaker inside a bookshelf or against a wall will inflate the  
bass as well as confine the speaker’s output. For best sound reproduction, allow the  
sound from the speaker to emit without restriction. Do not place objects over the  
speaker grille. Do not obstruct the rear bass port.  
The Dual Alarm Speaker is magnetically shielded but it is best kept at least 5” away  
from a computer monitor or television set.  
Cleaning  
Never use harsh cleaners or solvents or abrasive pads. The face may be cleaned with a  
slightly damp, soft cloth. Take care not to rub too hard. For the wood cabinet, liquid  
polish usually yields better results than spray-on waxes. Do not use glass cleaner or  
other chemicals to clean the clock’s window.  
Painting or staining the cabinet is not recommended and will void your warranty.  
Since the cabinet is natural wood, it is not always possible to achieve an exact  
color/grain match between the main unit and other Tivoli Audio products. You  
may also notice the wood darken over time.  
9
 
Warranty  
Tivoli Audio manufactures its products to very high standards and we are confident our  
products will perform well. Accordingly, we warranty this product against manufacturing  
defects in material and workmanship to the original owner, for a period of one year from  
the original date of purchase. This warranty is non-transferable.  
This warranty does not extend to damage caused by improper use/installation, faulty  
ancillary equipment, modifications, unauthorized repair, shipping damage or loss,  
abuse, accidents, use on improper voltage/current, power surges, lightning or other  
acts of God, normal wear and tear, or commercial use. Please consult the dealer  
from which you purchased this product for warranty service or repair. Proof of  
purchase may be required.  
Please resist the temptation to take apart this product. There are no user serviceable parts  
inside, and any attempt at modifying or repairing your unit will void the warranty.  
Tivoli Audio will not pay for costs incurred due to correction of reception problems,  
elimination of externally generated static/noise, loss of time, inconvenience, loss of use  
of product, or damage caused by improper use of this product.  
This warranty gives you specific legal rights, and you may also have other rights which  
vary from state to state. Some states do not allow limitations on implied warranties or the  
exclusion of consequential damages, therefore, such restrictions may not apply to you.  
If you purchased an extended service contract from your dealer and service is required  
after the manufacturer’s warranty has expired, please contact your dealer to obtain service.  
For your convenience, you may register your product for warranty coverage on the web  
days of purchase.  
Please visit Tivoli Audio’s FAQ section before calling or e-mailing with questions:  
10  
 
Specifications  
Model:  
Type:  
Tivoli Audio Dual Alarm Speaker™  
Quartz analog clock with speaker  
One 3" full-range driver  
Driver:  
Power Supply: MDA-PS, 12VDC, 10mA, 120V-60Hz (UL); 230V-50Hz (CE)  
Clock Battery:  
Dimensions:  
AA/UM-3 1.5V Alkaline  
8.375" W x 4.5" H x 5.25" D  
21.27 cm W x 11.43 cm H x 13.34 cm D  
2.94 lbs (1.33 kg)  
Weight:  
Specifications subject to change without notice.  
Tivoli Audio reserves the right to make product changes without notice.  
Tivoli Audio, the Tivoli Audio logo, Model Three, Dual Alarm Speaker  
and the Stereo Speaker are trademarks of Tivoli Audio, LLC.  
11  
 
This manual was written by Peter Skiera and is  
the property of Tivoli Audio. Tivoli Audio shall  
not be held liable for operational, technical, or  
editorial errors/omissions.  
For more information about other exciting  
products by Tivoli Audio, please visit our  
website or contact us directly:  
Tivoli Audio, LLC  
One Broadway, Suite 600  
Cambridge, MA 02142 USA  
1.877.297.9479  
MD0805  
 

Taylor Computer Hardware CONROE1333 DVI H User Manual
Taylor Scale 5754 User Manual
Texas Instruments Network Router 28xxx User Manual
Toshiba DVD Player SD 6980SY User Manual
Toto Plumbing Product CST 703 User Manual
Transition Networks Switch CSEFE10XX 10X User Manual
Transition Networks TV Converter Box SGETF1013 100 User Manual
Uniden Portable Radio UH012 User Manual
Verbatim Blu ray Player Blu ray HD DVD User Manual
Weed Eater Lawn Mower WET2242STD User Manual