Instruction Manual
®
Intelli-Time Digital Clock
model 75071T
CONTENTS
Troubleshooting ..................... 5
Care & Maintenance.............. 6
Replace Intelli-Time Battery ... 6
Specifications......................... 6
FCC Information .................... 6
Customer Support.................. 7
Warranty............................... 7
Unpacking Instructions ........... 2
Package Contents .................. 2
Product Registration ............... 2
Features & Benefits................. 3
Clock Setup........................... 4
®
®
Intelli-Time Clock .................. 4
Set the Time & Date ............... 5
Using the Clock...................... 5
Questions? Contact Customer Support at
(877) 221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Features & Benefits
1
2
3
4
®
1. Intelli-Time Clock
9. TIME ZONE Button
10. RESET Button
2. AM/PM Indicator
3. Time Zone Indicator
4. Daylight Saving Time Indicator
Full reset to factory defaults
11. DST OLD/NEW/OFF Switch
for DST setup preferences.
5. Integrated Hang Hole
12. Battery Compartment
For easy wall mounting.
®
13. Intelli-Time Battery
6. SET Button
7. UP Button
Compartment
14. Fold-Out Stands
8. DOWN Button
5
6 785 9 10
5
14
11 12
13
14
3
SETUP
Install or Replace Batteries
1. Remove the battery compartment cover.
2. Insert 4 x AA alkaline batteries into the battery compartment, as shown.
Follow the polarity (+/-) diagram in the battery compartment.
3. Replace the battery cover.
Install or Replace Batteries
4 AA alkaline batteries
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.
Intelli-Time® Clock
Intelli-Time clock and calendar are pre-programmed to the correct time and
date, and update automatically for Daylight Savings Time. All you need to do
is select your time zone using the “TIME ZONE” button.
4
Set the Time & Date
Set the time zone (HAST, AKST, PST, MST, CST, EST, AST) by pressing the
“TIME ZONE” button, located on the back of the clock. The Time Zone
selected is indicated on the clock display.
Set the Daylight Saving Time preference (NEW, OLD, OFF) using the DST
switch, located on the back of the clock. If you live in an area that observes
Daylight Savings Time, DST should be set to "NEW", even if it is not currently
Daylight Savings Time. While DST is being observed, "Daylight ST" is indicated
on the clock display.
Press and hold the “SET” button for 3 seconds to enter SET MODE. Once in
SET MODE the preference you are currently setting will blink on the clock.
To adjust the currently selected (flashing) item, press and release the “UP” or
“DOWN“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the "SET" button to adjust the next
preference. The preference order is as follows:
CLOCK HOUR (Please note AM/PM indicator)
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
You will automatically exit SET MODE if no buttons are pressed for 15 seconds.
Enter SET MODE any time by pressing and holding "SET" button for 3 seconds.
OPERATION
Using the Digital Clock
To view the MONTH/DATE/YEAR, press and release the "SET" button. Press
"SET" button again to display time. If no buttons are pressed after 15 seconds
the display will automatically display time again.
Troubleshooting
• Reset the unit by pressing the reset button located on the
Clock is too dark,
back of the clock. This will reset the clock to the original
hard to read or
factory settings. Time and date will need to be entered
after a reset.
doesn’t work
If your AcuRite product does not operate properly after trying
(877) 221-1252 for assistance.
5
Care & Maintenance
Clock Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
Replace Intelli-Time Clock Battery
Intelli-Time technology is powered
by a pre-installed coin-cell battery
that stores the time and date
settings. The battery has a shelf
life of several years. To replace
the Intelli-Time battery:
1. Locate the coin cell battery
compartment door on the back
of the display unit. Unscrew and
remove the compartment cover.
2. Insert 1 x CR2032 coin cell battery into the battery compartment, as shown.
Install battery with “+” positive terminal facing right.
3. Screw in the battery cover.
Specifications
POWER
4 X AA alkaline batteries
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
6
Customer Support
AcuRite customer support is committed to providing you with best-in-
class service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(877) 221-1252
24/7 support at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
IMPORTANT
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
Register a Product
►
Limited One Year Warranty
warranty will not be breached, and Chaney will give no credit
for products it manufactures which have received normal wear
and tear, been damaged (including by acts of nature), tampered,
abused, improperly installed, damaged in shipping, or repaired
or altered by others than authorized representatives of Chaney.
At AcuRite, we proudly uphold our commitment
to quality technology. Chaney Instrument Co.
warrants that all products it manufactures to
be of good material and workmanship, and to
be free of defects when properly installed and
operated for a period of one year from the date
of purchase.
The above-described warranty is expressly in lieu of all other
warranties, express or implied, and all other warranties are
hereby expressly disclaimed, including without limitation the
implied warranty of merchantability and the implied warranty
of fitness for a particular purpose. Chaney expressly disclaims
all liability for special, consequential or incidental damages,
whether arising in tort or by contract from any breach of this
warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Chaney further disclaims all
liability from personal injury relating to its products to the extent
permitted by law. By acceptance of any of Chaney’s products,
the purchaser assumes all liability for the consequences arising
from their use or misuse. No person, firm or corporation is
authorized to assume for Chaney any other liability in connection
with the sale of its products. Furthermore, no person, firm or
corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing
and signed by a duly authorized agent of Chaney. This warranty
gives you specific legal rights, and you may also have other
rights which vary from state to state.
We recommend that you visit us at
your product. However, product registration
does not eliminate the need to retain your
original proof of purchase in order to obtain
warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures
to be of good material and workmanship, and to be free of
defects when properly installed and operated for a period of
one year from the date of purchase. Remedy for breach of this
warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is
proven to breach the warranty contained herein within ONE
YEAR from date of sale will, upon examination by Chaney,
and at its sole option, be repaired or replaced by Chaney.
Transportation costs and charges for returned goods shall
be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
7
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
It’s more than accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark
of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and
copyrights are the property of their respective owners. AcuRite uses patented
Printed in China
75071T INST 022614
|