Taylor Blender AC 1200 BL User Manual

by  
Chopper & Blender  
Prep System  
Instruction Manual  
Item # AC-1200-BL 120V ~ 60Hz 260W  
 
IMPORTANT SAFEGUARDS  
When using electrical appliances, basic safety precautions should always be followed, including  
the following:  
1. READ ALL INSTRUCTIONS COMPLETELY BEFORE USING.  
2. To protect against electrical shock do not immerse or rinse cord, plugs or this appliance in  
water or any other liquid.  
3. Close supervision is necessary when any appliance is used by or near children.  
4. Unplug from outlet when not in use, before putting on or taking off parts and before  
cleaning.  
5. Avoid all contact with moving parts and blades.  
6. Do not operate any appliance with a damaged cord or plug or after the appliance mal-  
functions, or has been dropped or damaged in any manner. Return the appliance toTay-  
lor® (see warranty) for examination, repair or adjustment.  
7. Do not use attachments that are not supplied for this appliance fromTaylor®. The use of  
attachments, including canning jars, is not recommended byTaylor and may cause a risk  
of injury to persons, or permanently damage this product.  
8. Do not use outdoors.  
9. Do not let cord hang over edge of table or counter, or touch hot surfaces including a  
stove.  
10. Keep hands and utensils out of the blender container or chopper bowl while blending or  
chopping to reduce the risk of severe injury to persons or damage to the Chopper &  
Blender. A scraper may be used but must only be used when the Chopper & Blender is  
not running.  
11. Blades are sharp;handle very carefully.  
12. To reduce the risk of injury, never place cutter-assembly blades on the base without the  
blender jar or chopping bowl properly attached. Ensure the unit is completely assembled  
before using.  
13. Do not operate uncovered;always operate the blender and chopper with the cover in  
place. Do not attempt to remove the cover until blades have come to a complete stop.  
14. Do not blend hot liquids.  
15. Make sure the motor stops completely and the electrical cord is unplugged before disas-  
sembling or cleaning.  
16. To disconnect, be sure the unit is off, then remove the plug from the wall outlet by grasp-  
ing the plug and pulling. Never unplug the appliance by pulling on the cord.  
17. When using this appliance, provide adequate air space above and on all sides for air circu-  
lation.  
18. Do not place this appliance near a hot gas or electric burner or in an oven.  
19. Do not leave the appliance unattended during use.  
20. Do not use this appliance for other than its intended use.  
21. The Chopper & Blender does its work in seconds. Never process for extended periods.  
22. Do not operate the Chopper & Blender while it is empty.  
23. Before using, check that there are no unwanted objects inside the chopper or blender  
containers.  
24. Do not attempt to defeat the covers interlock mechanism, as serious injury may result.  
SAVETHESE INSTRUCTIONS  
 
3
SPECIAL INSTRUCTIONS  
This appliance is for HOUSEHOLD USE ONLY.  
This appliance has a polarized plug (one blade is wider than the other). To re-  
duce the risk of electrical shock, this plug will fit in a polarized outlet only one  
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does  
not fit, contact a qualified electrician. Do not modify the plug in any way.  
Make sure the voltage in your outlet is the same as the voltage indicated on  
the appliance. For 120 –Volt AC electrical outlet only.  
The length of the cord used on this appliance was selected to reduce the haz-  
ards of becoming tangled in, or tripping over a long cord. For safety, it is not  
recommended to use an electrical extension cord with this appliance.  
Do not immerse or rinse base of unit, plug or cord in water or other liquids.  
Use with wall receptacle only.  
Do not attempt to service this unit yourself.  
Pulse Operation  
This appliance operates with Pulse Control.The unit will operate only as long  
as the 2-Speed Power Button is held down.When the 2-Speed Power Button  
is released, the unit will automatically turn OFF. To restart, power off then  
turn back on.  
INTRODUCTION  
Now you can learn how to prepare and enjoy great tasting, healthy meals in min-  
utes using your The Biggest Loser™ Chopper & Blender Prep System by Taylor®.  
You will learn how to make the delicious and easy recipes that cut out calories,  
but leave in all the taste. The appliance and recipes are great tools to get you on  
track. There are over 125 more healthy and delicious recipes that you can find in  
the Biggest Loser Cookbook. When you start eating right, you may feel better,  
have more energy and feel empowered. For more information on NBCs The  
Biggest Loser, or to join The Biggest Loser Club, please visit the official Biggest  
Loser web site at www.nbc.com/The_Biggest_Loser.com or www.biggestloser-  
club.com  
 
4
DESCRIPTIVE DIAGRAM  
Measuring Cup  
Blender Cover  
Chopper Cover  
Blender  
Container  
Chopper Blade  
Chopper Bowl  
2 Speed Button  
 
5
USING YOUR CHOPPER & BLENDER PREP SYSTEM  
BEFORE FIRST USE  
Make sure the voltage in your outlet is the same as the voltage indicated on  
the appliance. This product is for 120 –Volt AC electrical outlet only.  
The chopper bowl is equipped with a safety locking system to increase secu-  
rity during operation. The chopper function will not work if the chopper  
bowl, blades and cover are not properly locked in place.  
Remove any bags, labels or stickers from the appliance.  
Clean the unit with a damp soft cloth.  
Wash all of the removable parts – chopper bowl, blade and cover, blender con-  
tainer, cover and measuring cup, using a sponge, warm water and mild dish  
detergent. Rinse and dry carefully.  
NOTE: do not immerse the base unit in water when cleaning  
HOW TO USE YOUR CHOPPER  
Place the unit on a flat, sturdy surface with adequate clearance (i.e., do not  
place under wall cabinets or on carpeting or other soft surfaces). This appli-  
ance is not for use in convection or conventional ovens, microwaves, or on  
stovetop.  
Make sure the appliance is switched off and unplugged.  
Wash and dry all components thoroughly as stated above.  
Assemble with chopper components. Always be sure that the appliance is  
properly assembled before using. Chopper blades are extremely sharp; never  
touch the cutting edge of blades.  
Clean and wash the food to be used.  
Add food ingredients to the chopping bowl, distributing them evenly with a  
spatula (not included). When chopping larger foods, pre-cut them into pieces  
of an even size, approximately ½ inch to ¾ inch pieces.  
Place the cover onto the chopper bowl. NEVER OPERATE THE  
CHOPPER UNLESS THE COVER AND BOWL ARE COR-  
RECTLY LOCKED IN.  
Plug the appliance into the power outlet.  
Start the chopper by pushing the 2 speed button continuously. The chopper  
operates with pulse control – press the button once and the chopper will op-  
erate for 45 seconds then stop automatically. Press the button again to operate  
for an additional 45 seconds.  
Reverse the above procedure to remove the chopper cover, blade and bowl.  
 
6
HOW TO USE YOUR BLENDER  
Place the unit on a flat, sturdy surface with adequate clearance (i.e., do not  
place under wall cabinets or on carpeting or other soft surfaces). This appli-  
ance is not for use in convection, or conventional ovens, microwaves, or on  
stovetop.  
Make sure the appliance is switched off and unplugged.  
Wash and dry all components thoroughly as stated above.  
Assemble with blender components. Always be sure that the appliance is  
properly assembled before using. Blender blades are extremely sharp; never  
touch the cutting edge of blades.  
Add ingredients to the blender a little at a time to ensure proper blending and  
to prevent overflow. Never fill container more than ¾ full; the action of the  
blade will cause ingredients to rise in the container. Make large recipes in  
multiple batches.  
Unless the recipe states differently, pour liquid ingredients into the blender be-  
fore solid ingredients. The liquid will help the processing time go faster and at  
a lower speed. Always add 1 cup of liquid before processing ice.  
Place the cover and measuring cup onto the blender.  
Plug the appliance into the power outlet.  
Switch on by pressing the 2 speed button continuously. The blender operates  
with pulse control – press the button once and the blender will operate for 45  
seconds then stop automatically. Press the button again to operate for an addi-  
tional 45 seconds.  
Reverse the above procedure to remove the blender cover and container.  
 
7
TIPS FOR PROCESSING FOOD AND SELECTING THE RIGHT  
OPERATION CONTROL  
Chopper Blade  
for chopping and  
grinding  
CHOPPING: Make sure that the bowl, blade and cover are in proper position.  
The “LO” and “HI” pulse buttons are designated for chopping, pureeing and mix-  
ing food. Use this function also for soft foods such as herbs, celery, onions, garlic,  
sauces and in preparation of salad dressings. Normally, 2 or 3 pulses are enough for  
chopping. Several pulse actions will help the food drop to the bottom for better  
chopping. Check the food frequently to prevent over processing.  
GRINDING: Make sure that the bowl, blade and cover are in proper position.  
The “LO” and “HI” pulse buttons are designated for grinding coffee beans, dry  
fruits, hard cheese, chocolate, etc. For these foods, use continuous pulse for several  
seconds. The desired result for preparing seeds or coffee will always depend on  
taste but 20 to 40 seconds is normally enough.  
BLENDING: Make sure the blender container and cover are in proper position.  
Blend for 30 seconds to one minute and check consistency. Continue blending  
until the desired consistency is reached. Over-blending will result in loose consis-  
tency.  
A scraper may be used (not included), but must only be used when the blender is  
not running. Thick mixtures require special attention during blending. Periodi-  
cally turn off the unit and scrape the mixture off of the sides of the container in-  
ward toward the blade. Replace the cover and continue blending. Select a higher  
speed if blending becomes sluggish. When the measuring cup is removed, you can  
add ingredients a little at a time through the hole in the blender cover. Always cut  
solid foods such as cheese or vegetables into small chunks before placing in the  
blender.  
NOTE: always operate the Chopper & Blender Prep System with the cover in  
place.  
 
8
IMPORTANT OPERATION INFORMATION  
Stability during processing: Due to the high power of the unit, it is recom-  
mended to use one hand to hold the unit while running. Make sure the cover  
is securely in place and keep hands away from blades and moving parts.  
Maximum operating time: Never use the appliance continuously for more  
than 1 minute at a time. OVERTIME OPERATION PROTECTION – a  
timer is built into the Chopper & Blender Prep System. It will automatically  
cut off the power when continuous operating time has reached one minute.  
Release the power button and allow the appliance to cool down before start-  
ing the next operation.  
Maximum quantity: Never overload the Chopper bowl or Blender container.  
As a guide, the maximum volume of ingredients to be processed is about ¾ of  
the chopper bowl or blender container capacity after processing.  
Chopper bowl and Blender container: The bowl and container are made of  
high quality plastic. However they may become scratched when used for  
grinding dry fruits, beans, nuts or some herbs. These scratches will not affect  
the performance or hygiene of the appliance.  
Removing food from the sides of the chopper bowl or blender container: If  
during processing you find some food sticking to the sides, unplug the unit  
and wait until the blades have come to a complete stop. Remove the cover  
and use a spatula to scrape the food inward toward the center and blades.  
DO NOT USE YOUR HAND OR FINGERS.  
CLEANING AND MAINTENANCE  
After each use and before cleaning, unplug the appliance from outlet and allow the  
unit to stop. DO NOT ATTEMPT TO CLEAN WHILE THE MOTOR IS  
RUNNING OR THE COMPONENTS ARE STILL MOVING.  
CAUTION: NEVER IMMERSE THE BASE UNIT, CORD OR PLUG  
IN WATER  
Open the securing clamps by pushing the release button.  
Remove chopper bowl/blender container, cover and blades. It is recommended  
to wash the components immediately after each use in warm, soapy water.  
Rinse and dry thoroughly. Chopper blades are extremely sharp. Wash chopper  
blades carefully and avoid direct contact with the blades themselves.The pre-  
ferred method of drying is to lay on a flat surface and air dry. Do not leave the  
blade where children can reach it.  
Chopper bowl and cover and blender container and lid areTOP RACK dish-  
washer safe. Put the blades in the cutlery basket of your dishwasher, but handle  
carefully.  
NEVER WASH THE BASE MOTOR UNIT.To clean the base, wipe clean  
with a damp sponge or cloth and dry immediately. Never use excess water,  
treated cloths, harsh cleaning agents, or sprays.  
Reassemble all parts and store in a dry place, unplugged and away from the  
reach of children.  
Some foods may discolor the containers. This is normal and will not affect the  
flavor of your food. Rub a soft cloth, dipped in vegetable oil to remove discol-  
oration.  
 
9
CHOPPING GUIDE  
 
10  
TROUBLESHOOTING  
The Chopper & Blender Prep System will not operate.  
Has a household fuse blown, or has a circuit breaker tripped?  
Is the power supply cord properly seated in the unit and the outlet?  
Is the inter-locking bowl and lid secured properly?  
Has the cord been damaged in some way? If so, DO NOT USE THE AP-  
PLIANCE. Contact Customer Service for replacement information.  
Has the auto-shut off feature activated?  
The Chopper & Blender Prep System is vibrating.  
Are the components securely positioned in the base? If not, turn off the unit  
and reposition the components onto the unit base.  
Has the appliance been overloaded? Attempting to process large quantities or  
large pieces of food may cause vibration. See section titled “How to use your  
Chopper” or the Chopping Guide.  
The lid will not seat properly.  
Is the product assembled properly?  
Is there food blocking the ability to close the lid properly? If so, remove half of  
the ingredients and process in two batches.  
Food is unevenly chopped.  
Either you are chopping too much food at one time, or the pieces are not  
small enough. Try cutting food into smaller pieces of even size and processing  
a smaller amount per batch.  
Food is chopped too fine or is watery.  
The food is over processed. Use brief pulses, or process for less time.  
Food is collecting on the sides of the bowl or container.  
You may be processing too much food. Turn machine off. When the blade  
stops completely, remove cover and clean with a spatula, turning food inward  
toward the blade.  
Food hangs up on the blade.  
You may be processing too much food or pieces are too large.  
See Chopping Guide.  
 
11  
WARRANTY  
Taylor® warrants this product to be free from defects in material or workmanship  
for one (1) year for the original purchaser from date of retail purchase. It does not  
cover damages or wear resulting from accident, misuse, abuse, commercial use, or  
unauthorized adjustment and/or repair. If service is required, do not return to re-  
tailer. Should this product require service (or replacement at our option), please  
contact Taylor Customer Service at 1-800-289-0944.  
There are no expressed warranties except as listed above.This warranty gives you  
specific legal rights, and you may have other rights which vary from state to state.  
If you need replacement parts:  
Use only Taylor specified parts. These specified parts will fit right and work  
right because they are made with the same precision used to build every new  
Taylor appliance.  
Keep this book and your sales receipt together for future reference. You must pro-  
vide proof of purchase for warranty purposes.  
For additional product information, or warranty information in Canada or else-  
where outside the USA, please contact us through www.taylorusa.com.  
Taylor® is a registered trademark of Taylor Precision Products and its affiliated  
companies.All rights reserved.  
Made to our exact specifications in China.  
www.taylorusa.com  
© 2008 The Biggest Loser is a registered trademark and copyright of NBC Stu-  
dios, Inc. & Reveille LLC.All Rights Reserved.  
AC-1200-BL 8.08  
 
12  

Topcom Telephone AXISS 130 User Manual
Top Innovations Sewing Machine SP 402 User Manual
Toshiba Telephone CTX670 User Manual
Tripp Lite Computer Monitor SUPDU001 User Manual
Troy Bilt Trimmer TB25ET User Manual
U Line Ice Maker ULN SS1095FCS 03A 115 Field Reversible User Manual
ViewSonic Car Video System VA2013wm User Manual
ViewSonic Digital Photo Frame VS12078 User Manual
VTech Laptop 80 067848 User Manual
Wagner SprayTech Paint Sprayer 323 User Manual