Planet Technology Switch MII Series User Manual

Fast / Gigabit Ethernet Switch Module  
MII series  
User's Manual  
 
communications. Operation of this equipment in a residential area  
is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
CE Mark Warning  
This is a Class A product. In a domestic environment, this product may  
cause radio interference, in which case the user may be required to  
take adequate measures.  
WEEE Warning  
To avoid the potential effects on the environment and human  
health as a result of the presence of hazardous substances in  
electrical and electronic equipment, end users of electrical  
and electronic equipment should understand the meaning of  
the crossed-out wheeled bin symbol. Do not dispose of WEEE as  
unsorted municipal waste and have to collect such WEEE separately.  
Revision  
User’s manual for Fast / Gigabit Ethernet Switch Module  
For model: MII-VSC / MII-VST / MII-VS15 / MII-VSA20 / MII-VSB20 /  
MII-GT/ MII-SX / MII-LX / MII-L40 / MII-L70 / MII-SFP /  
MII-LA15 / MII-LB15  
Rev: 7.0 (JULY, 2008)  
Part No: 2010-000021-007  
 
Table of Contents  
Chapter 1 OVERVIEW...................................................................... 5  
Chapter 2 MODEL LIST ................................................................... 6  
Chapter 3 CHECKLIST..................................................................... 7  
Chapter 4 INTRODUCTION ............................................................. 8  
4-1 1-Port 100Base-FX Fast Ethernet Modules-MII-VSC /  
MII-VST / MII-VS15 / MII-VSA20 / MII-VSB20.................... 8  
4-2 1-Port 1000Base-T Gigabit Ethernet Module-MII-GT............11  
4-3 1-Port 1000Base-SX/LX Gigabit Ethernet  
Modules-MII-SX / MII-LX / MII-L40 / MII-L70 /  
MII-LA15 / MII-LB15........................................................12  
4-4 1-Port 1000Base-T/Mini GBIC interface Module-MII-SFP ......14  
Chapter 5 Installing Optional Modules..............................................16  
 
Chapter 1 OVERVIEW  
Thank you for purchasing PLANET MII family Fast / Gigabit Ethernet  
module. The MII family Fast / Gigabit Ethernet module can install into  
PLANET FNSW / FGSW family Switch. The distance can be extended  
from 100 meters (TP), 2 kilometers (Multi-mode, SC or ST), up to 120  
kilometers (Single-mode, SC/LC).  
 
Chapter 2 MODEL LIST  
Your MII family Fast / Gigabit Ethernet module comes with one of the  
following models.  
Fiber connector  
and distance  
Model  
Interface  
Fast Ethernet  
MII-VSC  
100Base-FX Module  
(SC, MM, 2km)  
(ST, MM, 2km)  
(SC, SM, 15km)  
(SC, SM, 20km)  
(SC, SM, 20km)  
MII-VST  
100Base-FX Module  
100Base-FX Module  
100Base-FX Module  
100Base-FX Module  
MII-VS15  
MII-VSA20  
MII-VSB20  
Gigabit Ethernet  
MII-GT  
10/100/1000Base-T Module  
1000Base-SX Module  
1000Base-LX Module  
1000Base-LX Module  
1000Base-LX Module  
1000Base-T/Mini-GBIC Module  
1000Base-LX Module  
1000Base-LX Module  
(RJ-45, 100m)  
(SC, MM, 550m)  
(SC, SM, 10km)  
(SC, SM, 40km)  
(SC, SM, 70km)  
(RJ-45, 100m)  
(SC, SM, 15km)  
(SC, SM, 15km)  
MII-SX  
MII-LX  
MII-L40  
MII-L70  
MII-SFP  
MII-LA15  
MII-LB15  
Models with LX or last two numbered characters indicate the fiber-port  
is with “Single-Mode” optic fiber connector and the number indicates  
the maximum distance in km. The rest will be “Multi-Mode” optic  
fiber models.  
 
Chapter 3 CHECKLIST  
Your MII carton should contain the following items:  
The MII family Fast / Gigabit Ethernet module  
This user’s manual  
If any item is missing or damaged, please consult the dealer from  
whom you purchased your MII family Fast / Gigabit Ethernet module.  
 
Chapter 4 INTRODUCTION  
4-1 1-Port 100Base-FX Fast Ethernet Modules - MII-VSC /  
MII-VST / MII-VS15 / MII-VSA20 / MII-VSB20  
Figure 1. 1-Port 100Base-FX (SC, Multi-mode) Module Front View  
Features:  
● Comply with IEEE 802.3u, 100Base-FX Fast Ethernet standard  
● 1 x 100Base-FX fiber ports (SC/ST/single SC fiber connectors)  
● Store-and-Forward technology for abnormal packet filtering  
● For establishing fiber link with cable length up to 2km (Multi-mode  
module) and 15/20km (Single-mode module) or 412m (half-duplex  
mode)  
● Slide switch for Half /Full-Duplex selection (default in full-duplex)  
● Plug and Play Installation  
1. The fiber connector and distance support will be  
different by various models.  
2. The MII-VSA20/VSB20 should runs in pair. It means  
you must connect MII-VSA20 in one end and another  
MII-VSB20, for example, in the other end.  
Note  
 
LED DEFINITION  
LED  
Color  
Function  
Lit: indicate the link through that port is  
successfully established.  
Blink: indicate that the switch is actively sending  
or receiving data over that port.  
LNK/  
ACT  
Green  
Lit: indicate that port is operating in full-duplex  
mode.  
Off: indicate that port is operating in half-duplex  
mode.  
FDX  
Orange  
Blink: if a collision is detected when the port is  
in half-Duplex mode.  
Table 1. LED definition of 100Base- FX module  
Slide switch settings:  
Figure 2 shows the 100Base-FX module slide switch overview and the  
screen in Figure 3 appears shows the web settings for working under  
100Mbps full-duplex mode and half-duplex mode.  
Please make sure you have correctly configured the 100Base-FX  
module in the same duplex mode between the module’s slide switch  
and web interface speed duplex mode settings of module slots before  
physically installing the modules.  
FULL  
HAL F  
Figure 2. Slide switch overview of 100Base- FX module  
 
Figure 3. 100Base- FX module duplex mode setting of web interface  
Table 2 below shows the settings for working under 100Mbps full-  
duplex mode and half-duplex mode. Both module (slide-switch) and the  
switch (web interface) should be fixed on the same mode.  
Speed/duplex  
100Full-duplex mode  
Full-duplex mode  
100 Full  
100Half-duplex mode  
Half-duplex mode  
100 Half  
Hardware (module)  
Software (firmware)  
Table 2. Settings of 100Base-FX module  
Table 3 below shows the slide switch operation for full duplex and half  
duplex mode.  
Slide Switch Description  
The module works on full duplex mode. The other side must  
be also configured on full duplex mode. This provides up  
to 2km distance by multi-mode module and 15/20km by  
FDX  
single-mode module.  
The module works on half duplex mode. The other side must  
HDX  
be also configured on half duplex mode. This provides up to  
412m distances.  
Table 3. Slide switch settings of 100Base-FX module  
10  
 
4-2 1-Port 1000Base-T Gigabit Ethernet Module-MII-GT  
Figure 4. 1-Port 1000Base-T Module Front View  
Features:  
● Comply with IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet, IEEE  
802.3ab Gigabit Ethernet standard  
● 1 x 10/ 100/1000Mbps N-Way auto-negotiation switch port  
● Automatic MDI/MDI-X crossover function  
● Store-and-Forward technology for abnormal packet filtering  
● Non-blocking and full wire speed forwarding rate  
● LED indicators for Speed status  
● Up to 100m over 4-pair UTP Cat.5e cable  
● Plug & Play Installation  
11  
 
LED DEFINITION  
LED  
Color  
Function  
Lit: indicate that the port is operating at  
1000Mbps.  
LNK/ACT  
1000  
Off: indicate that the port is operating at 10  
Mbps or 100Mbps.  
Blink: indicate the traffic sending or receiving  
over that port.  
Green  
Green  
Green  
Lit: indicate that the port is operating at  
100Mbps.  
Off: indicate that the port is operating at 10  
Mbps or 1000Mbps.  
Blink: indicate the traffic sending or receiving  
over that port.  
LNK/ACT  
100  
Lit: indicate that the port is operating at  
10Mbps.  
Off: indicate that the port is operating at 100  
Mbps or 1000Mbps.  
LNK/ACT  
10  
Blink: indicate the traffic sending or receiving  
over that port.  
Table 4. LED definition of 1000Base-T Module  
4-3 1-Port 1000Base-SX/LX Gigabit Ethernet Modules-  
MII-SX / MII-LX / MII-L40 / MII-L70 / MII-LA15 /  
MII-LB15  
Figure 5. 1-Port 1000Base-SX Module Front View  
12  
 
Features:  
● Comply with the IEEE 802.3z Gigabit Ethernet standard  
● 1 X 1000Mbps fiber port (SX/LX/single SC fiber connectors)  
● Store-and-Forward technology for abnormal packet filtering  
● Full-duplex mode supported  
● Plug and Play Installation  
● LED indicators for LNK/ACT, FDX status  
● MII-SX provide distance up to 220m over 62.5/125μm fiber cable  
and 500m over 50/125μm fiber cable  
● MII-LX provide distance up to 550m over multimode fiber cable and  
10km over 9/125μm single mode fiber cable  
● MII-L40 provide distance up to 550m over multimode fiber cable and  
40km over 9/125μm single mode fiber cable  
● MII-L70 provide distance up to 550m over multimode fiber cable and  
70km over 9/125μm single mode fiber cable  
● MII-LA15 / LB15 provide distance up to 550m over multimode fiber  
cable and 15km over 9/125μm single mode fiber cable  
1. The fiber connector and distance support will be  
different by various models.  
2. The MII-LA15/LB15 should runs in pair. It means you  
must connect MII-LA15 in one end and another MII-  
LB15, for example, in the other end.  
Note  
LED DEFINITION  
LED  
Color  
Function  
Lit: indicate the link through that port is  
successfully established.  
Blink: indicate that the switch is actively  
sending or receiving data over that port.  
LNK/ACT  
Green  
Lit: indicate that port is operating in full-  
duplex mode.  
FDX  
Orange  
Table 5. LED definition of 1000Base-SX/LX Module  
13  
 
4-4 1-Port 1000Base-T/Mini GBIC interface Module-  
MII-SFP  
Figure 6. 1-Port 1000Base-T/Mini GBIC Module Front View  
Features:  
● Comply with the IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet stan-  
dard  
● 1-Port 1000Base-T/Mini GBIC interface module  
● High performance Store-and-Forward architecture  
● Auto-MDI/MDI-X on 1000Base-T port  
● Mini-GBIC interface for optional Mini GBIC module  
● Plug and Play Installation  
● LED indicators for LNK/ACT status on 1000Base-T port  
● LED indicators for LNK/ACT, FDX status on Mini GBIC interface  
The MII-SFP module does not supports the 1000Base-T  
port and Mini-GBIC interface operate at the same time.  
Note  
14  
 
LED DEFINITION  
Mini GBIC interface  
LED  
Color  
Function  
Lit: indicate the link through that port is  
successfully established.  
Blink: indicate that the switch is actively  
sending or receiving data over that port.  
LNK/ACT  
Green  
Lit: indicate that port is operating in full-  
duplex mode.  
FDX  
Orange  
Table 6. LED definition of Mini GBIC interface from MII-SFP Module  
1000Base-T port  
LED  
Color  
Function  
Lit: indicate the link through that port is  
successfully established.  
Blink: indicate that the switch is actively  
sending or receiving data over that port.  
1000  
LNK/ACT  
Green  
Lit: indicate the link through that port is  
successfully established.  
Blink: indicate that the switch is actively  
sending or receiving data over that port.  
100  
LNK/ACT  
Orange  
Table 7. LED definition of 1000Base-T port from MII-SFP module  
1ꢀ  
 
Chapter 5 Installing Optional Modules  
You can purchase optional modules separately to meet the needs of  
your network. The process of installing optional modules is the same.  
Follow these steps to install the optional module:  
1.Power the Switch off before installing the optional module.  
2.Place the Switch on a flat surface. Grasp the thumbscrew on the  
sides of the optional module or blank bracket and turn counter-  
clockwise to unscrew them. You can also use a screwdriver. Remove  
the old module or the blank bracket and set aside. Do not discard  
the module or blank bracket. Put the module or blank bracket back  
in if you remove the new module.  
3.Install the new module by inserting it into the guides and sliding it in  
until it stops (See Figure 7). Press it firmly until you feel the module  
snap into place. Never force, twist or bend the optional module. The  
optional module slides in smoothly.  
4.Gently push the thumbscrews in and turn clockwise to tighten. Do  
not over tighten the thumbscrews.  
5.Power the Switch on after you have installed the new module. The  
Switch will automatically detect the new module.  
1
2
3
4
9
10  
11  
12  
WGSW-2402A  
Intelligent 10/100/1000Mbps Ethernet Switch  
100Mbps  
ACT  
100Base  
-
FX  
1
9
2
3
4
5
6
7
8
LNK/ACT  
100/10  
LNK/ACT  
100/10  
PWR  
Mbps  
1000  
TX  
RX  
WGSW-C1ST  
10 11 12 13 14 15 16  
100Base - FX  
5
6
7
8
13  
14  
15  
Slot  
2
100  
10  
WGSW-C1GT  
10/100/1000Base-T  
Figure 7. Insert the modules  
6.Take off the dust cover from the transceiver and plug the cable in, if  
you are installing a fiber optic module.  
7.Check the LEDs to verify that if there is a link and a proper connec-  
tion at the port.  
Please refer to the Switch’s user’s manual for more about Switch or  
module’s management.  
1ꢁ  
 

Peavey Stereo Amplifier PV 1500 User Manual
Philips Coffeemaker HD7800 User Manual
Philips Projector Head Hall C13 User Manual
Philips Universal Remote AZ 8348 User Manual
Philips Universal Remote SRU4205 User Manual
Philips Work Light P 5794 B User Manual
Phoenix Gold Speaker TI210D4 User Manual
Pioneer Stereo Amplifier PRS D2000T User Manual
Planet Technology Network Router ADU 2100 User Manual
Planet Technology Network Router PL 201 KIT User Manual