INSTRUCTIONS FOR PANAMAX SIGNAL LINE PROTECTION MODULES - PREMIUM SERIES
LINE
IN
RJ-45
EQUIP
OUT
RJ-45
LINE
IN
RJ-45
EQUIP
OUT
RJ-45
Model: MOD-AT2 (Secondary Protector)
EQUIP
OUT
RJ-14
LINE
IN
RJ-14
EQUIP
OUT
RJ-14
LINE
IN
RJ-14
EQUIP
OUT
S110D
EQUIP
OUT
S110D
LINE
IN
S110D
LINE
IN
S110D
LINE
IN
S110D
EQUIP
OUT
S110D
WIRING DIAGRAM AND SPECIFICATIONS
EQUIP
OUT
LINE
IN
EQUIP
OUT
LINE
IN
LINE
IN
EQUIP
OUT
RJ-11
RJ-11
RJ-11
RJ-11
EQUIP
OUT
LINE
IN
EQUIP
OUT
LINE
IN
MOD-AT2
RJ-11
RJ-11
RJ-11
RJ-11
For Analog Telephone Lines
LINE
IN
EQUIP
OUT
MOD-AT2
MOD-AT4
MOD-AT8110
MOD-DT4
• 4 Wires (1 RJ-14) Protected
• 260 Volt Clamping
• Auto-resetting PTC's
LINE
IN
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
RJ-11
SAT
/
CATV
EQUIP
OUT
RJ-11
The MOD-AT2 module is designed to protect
standard phone lines connected to computer
modems, telephones, pay-per-view ports, etc.
It will also protect DSL lines (ADSL, G.Lite)
going into the DSL modem. The MOD-AT2
module will protect a single phone line using
an RJ-11 (2 wire) cord or a dual phone line
using an RJ-14 (4 wire) cord.
1. Connect the telephone line to the LINE
jack on the module.
LINE
IN
EQUIP.
OUT
SAT
CATV
/
SAT
CATV
/
2. Use a modular cord to connect the
EQUIP modular jack to the equipment to be
protected.
MOD-UTP
MOD-CAT5
MOD-DBSTV
MOD-SPKP
These modules are approved accessories for use with compatible Panamax AC
base units. Compatible base units include the following:
DISCONTINUED PRODUCTS
CURRENT PRODUCTS
Model: MOD-AT4 (Secondary Protector)
AC Base Units
AC Base Units
WIRING DIAGRAM AND SPECIFICATIONS
M8HT-PRO
M8-HT
M8C-EX
PM8-EX
M4-EX
M4T-EX
M8-EX
Bl
Or
Gr
Br
Bl
Or
Gr
Br
M4
M8
M8KSU
M8COM
M8KSU
LINE
IN
RJ-45
M8DBS-EX
M8C-Pro
M8HC-Pro
EQUIP
OUT
RJ-45
PM8T-EX
PM8C-EX
M4T
M4L
M8T
M8C
PM8-HT
EQUIP
OUT
RJ-14
PM8DBS-EX M8C-EX
LINE
IN
RJ-14
EQUIP
OUT
S110D
LINE
IN
S110D
When properly installed, the base unit’s Connected Equipment Protection Policy
remains valid. All modules include a small rectangular bracket and mounting screws. This
bracket replaces the small triangular wall-mount bracket that comes with the models listed in
the CURRENT PRODUCTS above.
EQUIP
OUT
LINE
IN
RJ-11
RJ-11
EQUIP
OUT
LINE
IN
MOD-AT4
For Analog
RJ-11
RJ-11
Telephone
Lines
• 4 Pairs (8 wires) Protected
ping • Straight-Through Pinout
• 260 Volt Clam
The MOD-AT4 module is designed to pro-
tect standard phone lines and DSL (ADSL,
G.Lite) lines. Multiple input & output jacks
provide complete installation flexibility. The
following diagram shows how the
jacks/wires are interconnected. Different
cables/connections can be split or com-
bined to accommodate a variety of installa-
tions. For example:
• Two RJ14 (dual-line) cords connected to
the LINE side (upper 2 jacks) can be split to
four RJ11 (single-line) cords on the EQUIP
side.
Installation Instructions
1. Mount the rectangular bracket to the back
of the AC base unit with the #8-32 x 5/16”
machine screws.
Note: The brass ground connector must be
used with the bracket in order to bond the
module ground to the base unit’s ground.
Module
Bracket
• Four RJ11 (single-line) cords connected
to the LINE side can be combined into a
single RJ45 (8 wire) cord (upper jack) on the
EQUIP side.
Ground
Connector
2. Mount the signal line module to the
bracket (screws provided with the module).
• Incoming lines can be punched-down on
the 110 jack on the LINE side and four RJ11
(single-line) cords will connect from the
EQUIP side to the equipment.
Caution: Never install telephones
during a lightning storm.
Ground
Connector
3. Optional – The assembled base unit and
module(s) may be wall mounted if desired.
Ground
Connector
4. Connect the wiring to the signal line
module as shown in the appropriate follow-
ing section.
Model: MOD-AT8110 (Secondary Protector)
WIRING DIAGRAM AND SPECIFICATIONS
AC Base Unit
All telephone input/output connections will
be labeled with LINE and EQUIP.
Blue
Orange
Green
Blue
Orange
Green
Brown
EQUIP.
OUT
LINE
IN
Brown
Blue
Orange
Green
Blue
LINE
IN
S110D
EQUIP
OUT
S110D
Orange
Green
Brown
It is very important to connect
telephone signal lines properly.
Brown
An easy access
110
IDC
110
IDC
MOD-AT8110
L
I
PULL OUT card
is included on
the back of each
module for wiring
diagrams and
For Analog Telephone Lines
There are no designated
input/output connections
on coaxial protection
• 16 Wires (two 110 punch-downs) Protected
• 260 Volt Clamping
• Auto-resetting PTC's
SAT /
CATV
modules. These are
The MOD-AT8110 module is designed to
protect up to 8 standard phone lines using
110 punchdown connectors on both the
input LINE and output EQUIP.
cable to the LINE IN punchdown block on
the module.
bi-directional modules
in both transmission fre-
quency and voltage.
specifications.
2. Punch down another cable to the EQUIP
OUT punchdown block on the module and
connect to the phone equipment.
1. Cut the cable from the primary protector
to the correct length and punch down the
1
|