C8314A Size: A4
11.BATTERY COMPARTMENT:
Accommodates 2 AA size batteries.
Note
1.
2.
·
During the setting period, press and hold “+” or “-”
key to speed up the change of settings.
The time zone indicators are abbreviated as
below: P=Pacific, M=Mountain, C=Central,
E=Eastern.
12.RESET key:
·
·
Press it to return all values to default values.
In case of malfunction, the unit may be required
to reset.
Projection Alarm Clock
with Indoor Thermometer
Model: EW96
13.°C/°F slide switch:
USER MANUAL
ALARM TIME SETTING
·
Slide it to switch between Celsius and Fahrenheit.
Thank you for your purchase of this Projection Alarm
Clock. Please read these instructions carefully and
keep the manual well for future reference.
1.
In normal time mode, press “SET ALARM” key
once to enter the alarm time setting mode.
Press “+” or “-” key to set hour/minute.
Press “SET ALARM” key to save and exit the
setting mode. “ ” indicates alarm is ON.
14.PROJECTION ON/OFF slide switch:
·
Slide it to turn on/off the projector.
2.
3.
15.180° FLIP key:
The unit has a clear and easy-to-read display that
shows the indoor temperature, time and date.
·
Press it to rotate the projected image by 180°.
16.RCC key:
This product is designed to synchronize its date and
time automatically once it is within range of the WWVB-
60 signal from the atomic clock inFort Collins, Colorado.
·
In normal time mode, press it once to receive
the RC signal for reception testing.
Normal time mode
Note
Alarm time setting
17.BATTERY DOOR
OVERVIEW
RECEIVER
LCD DISPLAY
1. Time zone
1.
2.
The alarm will be automatically turned on when
you set the alarm time.
During the alarm time setting period, press and
hold “+” or “-” key to speed up the change of
settings.
1
2. Low battery indicator
3. Signal reception indicator
4. Indoor temperature
5. Time
2
6. Alarm time & Date
3
1
2
3
USING ALARM FUNCTION
5
6
ALARM
1.
Follow the directions above to set the alarm
time.
4
2.
3.
In normal time mode, press “ALARM ON/OFF”
key once to display the current alarm time.
Press it again to turn alarm ON/OFF.
OPERATING THE MAIN UNIT
1.
Remove the battery door and insert 2 new AA
4
size batteries as per the polarity information
marked on the battery compartment.
Press “RESET” key to restart the clock.
Slide “°C/°F” switch to select between Celsius
and Fahrenheit.
8
TO SILENCE THE ALARM
5
9
6
2.
3.
1.
Press “SNOOZE/LIGHT” to silence the alarm
for 8 minutes. The “ ” will be flashing.
Press any other key to turn the alarm off and
activate it again after 24 hours.
If no key is pressed within 120 seconds, the
alarm will be turned off and be activated again
after 24 hours.
7
2.
3.
10
4.
Replace the battery door.
RECEPTION OF RADIO CONTROLLED TIME SIGNAL
14
1213
The time and calendar are radio-controlled. The current
time and calendar are automatically synchronized with
the atomic clock signal from Fort Collins, Colorado.
When used for the first time (after inserting batteries
or pressing “RESET” key), the clock will start to search
for the atomic clock signal and the signal reception
icon will flash for 5 minutes.
USING THE PROJECTOR
Slide the “PROJECTION ON/OFF” switch to turn on/
off the projection light. The projection light must be on
a dark background and within 1-4 meters (3 to 12 feet)
from the clock, see example below:
15
16
11
17
SIGNAL RECEPTION INDICATOR
The wave segment flashing means time signals are
being received. The signal quality could be classified
into 3 types:
1.Projector:
·
Use it to project the time.
2.SNOOZE/LIGHT key:
No signal
Note
Weak signal
Excellent signal
·
·
In normal time mode, press it once to turn on
the backlight for 5 seconds.
Press it to silence the current alarm when it is
going and enter the snooze mode for 8 minutes.
1.
The unit will automatically search for the time
signal at 2:00am (3:00am or 4:00am is also
available if the signal is not received at 2:00am),
8:00am, 2:00pm, and 20:00 each day.
Note
3.LCD display:
1.
2.
3.
4.
5.
6.
Slide “PROJECTION ON/OFF” to turn on the
projection function.
Press “SNOOZE/LIGHT” to turn on the projector
for 5 seconds.
When using DC power adapter, the projector will
be turned on all the time.
·
Displays time, indoor temperature and date.
2.
Always place the unit away from electrical
devices such as televisions, computers,
telephones, etc.
4.+ key:
·
In time setting mode, press it to increase the
setting values.
3.
4.
Avoid placing the unit on or next to metal plates.
If possible, place the unit next to a window.
Signal reception is greatly decreased when located
in closed areas like basements or metal buildings.
Do not start reception in moving vehicles or trains.
If the alarm is set to go off, the alarm icon “
will be projected.
”
5.SET CLOCK key:
·
In normal time mode, press it once to enter the
normal time setting mode.
Press “180 FLIP” to rotate the projected image
by 180°.
Turn “FOCUS” knob to focus the projected image.
5.
·
In normal time setting mode, press it to step
the setting items. Press and hold it to exit the
setting mode in any step.
TIME AND CALENDAR MANUAL SETTING
If you are out of reach of the Radio Controlled sensor
or if the reception is not reachable, the time and calendar
can be set manually. As soon as the signal of sensor
is received again, the clock will automatically
synchronize with the exact time and calendar.
BATTERY REPLACEMENT
6.- key:
In time setting mode, press it to decrease the
setting values.
·
If the low battery icon turns on next to time, replace
the main unit’s battery with 2 new AA batteries.
7.DC jack:
1.
In normal time mode, press “SET CLOCK” key
once to enter the time setting mode.
Press “+” or “-” key to change the settings.
Press “SET CLOCK” to confirm. The setting order
is: 12/24-hr format, time, time zone offset, year,
day/month format, date.
Low battery indicator
·
Plug DC adaptor to power the clock.
2.
3.
8.ALARM ON/OFF key:
·
Press it once to turn on the backlight and display
the alarm time for 5 seconds.
·
Press it again to turn on/off the alarm.
4.
Press “SET CLOCK” key to save and exit the
setting mode.
9.SET ALARM key:
Note
·
Press it once to turn on the backlight for 5
seconds, and press it again to enter the alarm
time setting mode.
Attention! Please dispose of the used unit or batteries
in an ecologically safe manner.
12/24 Hr setting
Time setting
Time zone setting
·
In alarm time setting mode, press it to step the
setting items.
10.FOCUS turning knob:
Focus the projected image.
Month-Date setting
MD/DM setting
Year setting
·
|