®
S I M P L Y
A M A Z I N G
USER’S GUIDE
CARPET & HARD FLOOR CLEANER
XLS700series
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Warranty
• Safety Warnings
• Parts List
• Operating Instructions
• Accessories List
• Trouble Diagnosis
Warranty
Troubleshooting Guide
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company
gives you the following limited warranty for this product only if it was
originally purchased for residential use, not resale from Oreck or an Oreck
Authorized Retail Dealer.)
WARNING: Unplug cord from electrical
outlet before servicing.
PROBLEM
SOLUTION
Oreck will repair or replace, free of charge, to the original purchaser, any
part which is found to be defective in material or workmanship within one
(1) year of the date of purchase. This limited warranty applies to normal
domestic use. Any commercial use of this product will void this limited
warranty. Any use of non-Oreck cleaning solutions with this unit will void
this limited warranty.
Water and cleaning
solution is not dispensing
onto carpet or upholstery.
• Check that the upper supply tank is partially
filled with lukewarm water. Caution: Do not
overfill.
• Check that a cleaner cartridge is installed
and that the white lever is locked in the
downward position. Due to pressurization, the
cleaner will not properly operate without a
cleaner cartridge in place. If the cleaner
cartridge is empty, replace it with a full
cartridge.
This limited warranty does not cover the replacement of expendable or
consumable parts such as belts, brushes, and other parts subject to
normal wear unless they are defective in material or workmanship.
This limited warranty does not apply to any part subjected to accident,
abuse, commercial use, alteration, misuse, damage caused by act of God,
the use of voltages other than indicated on the serial number displayed on
this product or service of this product by other than Oreck or a
participating Factory Authorized Service Center.
• Check that the spray tips are not clogged.
Use a towel or damp cloth to clean.
• For above-the-floor cleaning, check that the
hand-held nozzle and hose assembly is
properly connected to the cleaner neck. Also
insure that the button lock has been
engaged.
Oreck does not authorize any person or representative to assume or grant
any other warranty obligation with the sale of this product.
• For best results, use a stain pretreatment,
such as Steemer Full Release® Professional
Spot & Stain PreCleaner. These solutions
loosen and break down most common
household grease, oil, and food stains.
• Make several slow passes over the stain
from different angles.
Not removing certain
stains. Heavy traffic area
spots.
Oreck’s limited warranty is valid only if you retain proof of purchase from
Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
• Make at least one additional pass over the
wet carpet without pressing the cleaner
button.
• Check that the handle trigger lock is not
engaged.
• With each pass, slowly pull the unit toward
you to extract any remaining liquid in the
carpet. To speed drying, gently push the
nozzle deep into the carpet pile.
• Check for airpath obstructions in the
stair/upholstery hose, cleaner neck and in the
nozzle. Check to insure that the inlet screen
is free of debris.
Carpet is excessively wet
after cleaning.
Oreck’s liability for damages to you for any costs whatsoever arising out
of this statement of limited warranty shall be limited to the amount paid for
this product at the time of original purchase, and Oreck shall not be liable
for any direct, indirect, consequential or incidental damages arising out of
the use or inability to use this product.
Note: Under normal
conditions, a carpet may
take up to four hours or
longer to completely dry.
Drying time depends on a
combination of various
factors including: carpet
type, carpet pile
thickness, temperature,
humidity, air circulation
and the number of wet
passes.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER
EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Excessive foaming at
spray tips.
• Check that the upper supply tank has water.
Dark streaks on carpet
after cleaning.
• Operate the machine more slowly; you will
achieve better results with one slow pass
than several fast strokes.
Some states do not allow limitations on the duration of implied warranties,
so the above limitation may not apply to you.
• Overlap each pass to provide maximum
cleaning without streaking.
• In high traffic or heavily soiled carpets, it is
occasionally beneficial to allow the carpet to
dry and repeat the process as needed to
achieve optimal cleaning.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Steemer brush roll will not • Check that the nozzle power cord is
CALL CUSTOMER SERVICE HOT LINE
turn.
completely connected to the main unit.
US: 1-800-989-3535 Canada: 1-888-676-7325
• If an obstruction stalls the brush roll, the belt
is designed to burn through so as to protect
the motor. Please insure through inspection
that the brush roll is free of obstructions and
is free to turn. Secondly, make sure that the
belt is in good working order. Replace the
belt if needed.
Whenever calling, please be sure to have your model and serial
number from data plate.
• If the belt and the brush roll become
excessively wet, momentary slippage can
occur. By running the unit on a dry section of
carpet for a minute or less, the belt will
function properly.
• Reinsert the plug, if it has slipped out of the
outlet.
Cleaner will not run or
suddenly stops.
• The A.L.C.I. may have tripped off due to
fluctuations in household current. Press the
reset button and restart the unit.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
2
2
3
6
9
1
c
a
b
b
a
a
4
5
a
TEST
RESET
8
7
a
b
c
10
13
16
11
14
17
12
15
18
b
a
3
c
19
22
20
21
c
a
b
d
b
a
Features
8. 25’ Power Cord
9. A.L.C.I. – Safety Plug with Reset and Test Buttons
10. Translucent Upper Supply Tank
11. Translucent Lower Recovery Tank
12. Transparent Nozzle Cover
13. Motorized Scrubbing Brush
14. Convenient quick-release Cord Wrap
15. Wiper for hard floor cleaning
16. Temperature Indicating Label
17. Floor Stand
a
Parts Checklist
Read all instructions thoroughly before assembly/use. Please unpack
carton, removing all parts and packages. Check that all parts required for
assembly are present by referencing the list below.
RED OPERATOR CONTROLS
18. Rinse/Shampoo Valve
PARTS
QUANTITY
19. Shampoo/Cleaner Spray Button
20. A.L.C.I. Plug Reset Button
21. Tank Latch
1. Oreck Steemer Unit
1
1
1
2
1
4
1
2. Handle
3. Oreck Steemer Power Nozzle
4. Large, easy-to-steer Wheels
5. Easy Lock-in Cleaner Cartridge/Bottle
6. Screws (5/8”)
22. On/Off Power Switch
23. Nozzle Change Button
24. Hand-held Nozzle Trigger
7. Hand-held Nozzle and Hose Assembly
To Assemble Cleaner
19
THE ONLY TOOL YOU WILL NEED IS A PHILLIPS-TYPE SCREWDRIVER!
fig. 1 Attach Handle to Cleaner:
22
a. Lay the cleaner on a flat surface with the tank side down or to its
2
side.
1
b. Slide handle into cleaner body until interlock is secured.
14
18
c. Insert four 5⁄8” screws (included) into the four cavities in the
handle base and tighten.
6
8
fig. 2 Attach Wheels:
a. Locate two wheels and two support legs.
10
b. Insert the wheels (a) into the support legs (b) by pushing the
9
wheels in until they snap into place.
RESET
11
TEST
20
fig. 3 Attach Nozzle:
5
Turn the unit so that the tank is face up.
21
16
23
a. Align the nozzle so the red nozzle change button is in line with
the corresponding hole in the nozzle. Depress the small red
nozzle change button and slide the nozzle over the unit shaft until
the button locks into place.
3
12
15
fig. 4 Plug the small power cord connected to the nozzle into the
receptacle in the back of the unit.
4
17
NOTE: Before using, please read the important safety and
operating instructions.
13
24
7
4
Insert Cleaning Cartridge/Bottle:
Servicing of Double-Insulated Appliances
NOTE: Cleaner will not operate without a cleaner cartridge locked
into the docking bay.
A double-insulated appliance is marked with one or more of the
following: The words “Double Insulation” or “Double Insulated” or the
Remove the cleaner cartridge/bottle cap.
double-insulation symbol (
). In a double-insulated appliance, two
fig. 11 Insert the cleaner cartridge into the docking bay on the
systems of insulation are provided instead of grounding. No grounding
means is provided on a double-insulated appliance, nor should a means
for grounding be added to the appliance. Servicing a double-insulated
appliance requires extreme care and knowledge of the system and
should be done only by qualified service personnel. Replacement parts
for a double-insulated appliance must be identical to the parts they
replace.
side of the cleaner.
a. The directions on the cleaner cartridge must be facing out.
b. Lock and seal the cartridge in the cleaner by rotating the
white lever on cartridge from top to bottom.
Test and reset the A.L.C.I.:
fig. 5 Plug in the power cord. Press the test button to shut off
power. To reset the A.L.C.I., simply push in the red reset
button on the plug.
Polarization Instructions:
To reduce the risk of electric shock, the Oreck Steemer model is
equipped with a polarized alternating current line plug (a plug having one
blade wider than the other). This plug will fit into a polarized outlet only
one way. This is a safety feature. If you are unable to fit the plug fully
into an outlet, try reversing the plug. If the plug should still fail to fit,
contact a qualified electrician to replace the obsolete outlet. Do not
defeat the purpose of the polarized plug in any way.
To Prepare Carpet
Always vacuum thoroughly before using the ORECK STEEMER
carpet and hard flooring cleaner. It provides excellent carpet and
hard floor cleaning on surfaces that are free of surface debris.
To achieve best results, high traffic areas and carpet stains should be
pretreated prior to cleaning using Steemer Full Release® Professional
Spot & Stain PreCleaner.
A.L.C.I
The Oreck Steemer is made to double-insulated specifications and is
equipped with an A.L.C.I. (Appliance Leakage Circuit Interrupter). The
A.L.C.I. shuts off the unit in potentially hazardous situations.
CAUTION: Before cleaning a carpet for the first time, test a small
area for color fastness.
Pour a small amount of Steemer Full Release® Professional Carpet
Cleaner on a clean white cloth and blot carpet. Examine this cloth for
color removal; if color appears on the cloth, the carpeting is not
colorfast and should not be cleaned with any wet extraction process.
fig. 5 The A.L.C.I. has a Test and Reset button which should be
operated each time the unit is plugged in.
a. Do not remove the tag which provides test instructions from
around the cord at the A.L.C.I. (A.L.C.I. may vary from illustration).
NOTE: This product is not recommended for use on carpets made
from silk, velvet, wool and some cotton blends. Check the
manufacturer’s cleaning recommendations.
DANGER: Improper installation of A.L.C.I. can result in electric shock.
Do not modify or by-pass the A.L.C.I. Do not replace any electrical
component in this product with anything other than an authorized
ORECK replacement part. The risk of electric shock can result if used in
the vicinity of improperly grounded stationary appliances (stove,
refrigerator, washer, etc.).
Operating Instructions
To Clean Carpets and Hard Flooring:
NOTE: DO NOT use on Hard Wood Flooring.
To Set-Up Cleaner
fig. 12 Turn the Shampoo/Rinse switch to the “SHAMPOO” position.
fig. 13 Place power switch in the “ON” position.
The Oreck Steemer carpet and hard flooring cleaner is designed for
fast and easy set-up.
fig. 14 Press the red button in the handle and while lifting the handle
slightly, slowly pull the cleaner backwards. Pressing the button
releases the cleaner and water mixture. As you pull the nozzle
over the sprayed floor, the nozzle extracts the solution from the
floor and stores the dirty water in the recovery tank.
fig. 6 Swing the wheels away from the nozzle into the operating
position.
Remove the supply/recovery tank:
fig. 7 Pinch the gray and red tank release latch together and gently
fig. 15 To move forward, slightly tilt the nozzle off the floor and roll the
cleaner forward. Repeat process working in small overlapping
rows for even cleaning until the entire room has been completed.
lower the latch to the nozzle. Do Not Force Latch!
fig. 8 Push the supply/recovery tank downward toward the nozzle and
lift out.
WARNING: Do not push forward! Pull the cleaner towards
you to clean. This cleaner has been specifically designed to
place the nozzle deep into the carpet.
fig. 9 Fill the supply tank:
a. Open the gray tank cap.
Push down gently on the handle to lift the nozzle out of the
carpet, to move forward and reposition the cleaner.
b. Fill the tank with hot tap water to the fill line, as noted on the side
of the tank.
IMPORTANT: Adjust the speed of the cleaning stroke to
your carpet and flooring conditions. Heavily soiled or
stained carpets or floors will require slower strokes. Avoid
oversaturating.
c. Use the temperature label on side of tank to check water
temperature. “OPTIMAL” should be showing on label when the
correct water temperature is achieved.
CAUTION: Do not overfill tank or use water that is too cold
or too hot. Do not put any type of shampoo/cleaner into the
supply tank. Use only Steemer Full Release® Professional
Carpet Cleaner cartridges, which are specifically formulated
to be residue-free. Other carpet shampoo will leave residues
in the unit that will over a short period of time clog the
dispensing system and void your warranty.
NOTE: The nozzle squeegee may be flipped for deeper
cleaning on deep pile carpets. See “To Replace Squeegee”
To shorten the drying time, go back over the floor pulling slowly
backwards without depressing the red button. Repeat this procedure
until you do not see water being pulled through the nozzle.
To Rinse Carpet and Hard Flooring:
fig. 10 Close tank cap and place the tank back on the cleaner. Lift the
gray latch to slide the tank upward into position until you hear a
“click”, signaling that the tank is securely locked into place.
fig. 12 Turn the Shampoo/Rinse switch to the “RINSE” position.
fig. 13 Place power switch in the “ON” position.
5
fig. 14 To rinse carpet or hard flooring, press the red button in the
handle. Slowly pull the cleaner backwards over already cleaned
area. Pressing the button releases clean water. As you pull the
nozzle over the sprayed floor, the nozzle extracts any remaining
solution from the floor and stores the dirty water in the recovery
tank.
fig. 17 Lower cleaner onto floor stand.
fig. 7/8 Remove the supply/recovery tank from the cleaner.
fig. 9 Open tank cap. Fill with hot tap water, close tank cap.
fig. 10 Replace tank onto cleaner.
fig. 16 Attach the hand-held nozzle and hose assembly to the cleaner
neck. Align the guide tab on top of unit’s neck with slot in hose
collar. Depress the red button and push the hose collar onto the
unit until the button locks securely in the collar hole.
fig. 15 To move forward, slightly tilt the nozzle off the floor and roll the
cleaner forward. Repeat process working in small overlapping
rows for even cleaning until the entire room has been completed.
fig. 13 Place power switch in the “ON” position.
CAUTION: Do not allow the lower recovery tank to overfill.
Damage to the unit can result. Empty the recovery tank when full
and whenever clean water is added to the upper supply tank.
fig. 14 Press the red button in the handle and push forward to lock.
fig. 18 Press the red cleaner dispensing trigger on the hand-held nozzle
fig. 7 To empty the recovery tank, simply release the tank latch by
to release cleaner.
squeezing the red and gray latch together.
To Prepare Upholstery:
fig. 8 Lift the tank out and carry it to a sink or drain. Turn the tank
IMPORTANT: Prior to cleaning any upholstered furniture read the
following instructions very carefully.
upside down and pour the dirty water out.
fig. 9 Refill the supply tank with clean hot water. Replace cleaner
Most modern upholstery fabrics may be safely cleaned by wet cleaning
methods; yet there are exceptions to this, as some delicate or unusual
fabrics require “dry cleaning.” If you are in doubt about the type of fabric,
we suggest that you check with the manufacturer or dealer where the
furniture was purchased. Most fabrics are wear coded by the
cartridge as needed.
NOTE: Cleaner will not operate without a cleaner cartridge
locked into the docking bay.
For heavily soiled carpets it may be necessary to clean from several
directions to insure that the carpet is thoroughly cleaned.
manufacturer which details cleaning methods for a particular fabric. If
necessary, bring in a cushion or arm cover to your dealer.
•
Cleaning upholstery which is covered with fabrics that are not
compatible with wet cleaning may result in damage to the fabric.
Know what the fabric is and how it may be cleaned before using the
Oreck Steemer cleaner.
Sample Cleaning Procedures:
You can use the Oreck Rinse-A-Matic™ Carpet and Hard Floor cleaner
in many ways to achieve optimal results. The following chart is a guide
to usage, however, feel free to use it in a manner which you think is
most effective depending on the surface.
•
Check the stuffing material if possible. Look inside cushions and
underneath the furniture. If the filling is colored, it may bleed through
and discolor the furniture. Most modern stuffing material is light
colored and colorfast.
The procedure section indicates the types of passes to use on the
flooring. For example “Shampoo - Dry - Rinse - Dry” means, one
shampoo pass, then one dry pass, one rinse pass (water only), then one
dry pass.
•
•
To remove loose dirt, vacuum upholstery thoroughly with a vacuum
cleaner.
If the upholstery is being cleaned for the first time, CHECK FOR
COLORFASTNESS. Test a small, area several hours before starting
to clean upholstery. Pour a small amount of Steemer Full Release®
Professional Upholstery Shampoo on a clean white cloth and blot
upholstery. Examine the cloth for color removal. If color appears on
cloth, the upholstery is not colorfast and should not be cleaned with
wet extraction methods. Let test area dry completely. Inspect for
changes in color, bleeding, stretching or shrinkage. Test another area
if in doubt. This product is not recommended for use on silk,
velvet, wool and some cotton blends.
Carpet Cleaning
Situation
Procedure
Monthly Maintenance Cleaning - Quick
Monthly Maintenance Cleaning - Standard
Shampoo - Dry
Pre-treat with “Spot & Stain
Remover” as necessary.
Shampoo - Dry - Rinse - Dry
Monthly Maintenance Cleaning - Thorough Pre-treat with “Spot & Stain
Remover”
Shampoo - Dry - Rinse - Dry
Rinse - Dry
To Clean Upholstery & Small Spill Pick-Ups:
Plug cord into an electrical outlet.
●
Thicker Carpet
Heavy Duty Cleaning
Traffic Lanes
Spots
Pre-treat with “Spot & Stain
Remover”
●
●
●
fig. 5 Test and reset A.L.C.I. on the plug.
fig. 11 Insert a specially formulated Steemer Full Release® Professional
Shampoo - Dry - Rinse - Dry
Rinse - Dry
Upholstery Cleaner Cartridge.
Hard Floor Cleaning
Situation
fig. 13 Turn cleaner on by placing the On/Off power switch in the “ON”
Procedure
position.
Quick Clean
Shampoo - Dry
fig. 14 Lock the cleaner button by pressing and sliding the button
Standard Clean
Pre-treat with “Spot & Stain
Remover” as necessary.
forward on the main handle.
Shampoo - Dry - Rinse - Dry
fig. 18 Depress the red dispensing trigger on the hand-held nozzle and
slowly drag the nozzle towards you. Make a second pass at right
angles to the first. This will minimize any streaking or uneven
appearance.
Heavy Duty Clean
Pre-treat with “Spot & Stain
Remover”
Shampoo - Dry - Rinse - Dry
Rinse - Dry
Several key precautions must be followed to insure
operator safety:
NOTE: Additional drying passes can be used to reduce carpet
and hard floor moisture and shorten drying time.
1. Always test and reset the Steemer A.L.C.I. plug.
2. Do not immerse the power nozzle of the Oreck Steemer.
3. Do not allow the lower recovery tank to overfill.
For Above the Floor Cleaning - Cars, Stairs, Etc.:
CAUTION: Set the red button in the handle to the floor (back)
position when using the hand held nozzle for extraction only.
4. Do not pick up corrosive, combustible, or flammable liquids such as
acids, gasoline, alcohol, or use this product in areas where vapors
from these types of materials are present.
Unplug the cleaner from the electrical outlet.
fig. 4 You will first need to unplug the separate power cord that
connects the Steemer nozzle to the cleaner.
5. Do not use to clean out bathtubs, flooded basements or any place
fig. 3 Remove the nozzle by depressing the red button located on the
side of the neck. Pull the nozzle straight back and off the neck
without twisting.
where the liquid depth exceeds 1⁄8”.
6
c. Remove and replace the old belt if broken or if excessive wear is
noted.
To Clean Carpet Cleaner
To Install a New Belt:
WARNING: To reduce the risk of electric shock or injury from
d. Remove brush roll and insert the new belt into the rectangular
cavity. Using a long screwdriver, loop belt around motor shaft.
Pull and stretch belt over crowned end of the brush roll. Rotate
brush to properly align belt.
moving parts, unplug before servicing.
Before turning the cleaner off, tilt the cleaner back, raising the nozzle off
the carpet for 15-20 seconds. This prevents extracted water in the
nozzle from dripping back onto the carpet after you turn the cleaner off.
fig. 21 Replace belt cover, brush roll clamp and screws.
fig. 3 Reattach power nozzle to unit.
fig. 13 Place the power switch in the “OFF“ position. Unplug the power
cord from the outlet.
fig. 4 Reconnect power cords and test.
fig. 11 Remove the cleaner cartridge by rotating the locking white lever
upwards. Do not store with a cleaner cartridge attached.
To Replace Squeegee
fig. 19 Remove and empty the tank. Rinse out the lower recovery tank
with warm water. Wipe off the inlet screen to remove
accumulated dirt, lint and debris.
fig. 22 Remove squeegee by gently pulling the handles located on each
fig. 10 Replace tank.
end of the squeegee until it releases.
fig. 20 If you have been operating the cleaner at length, it may be
necessary to clean the nozzle from time to time, particularly if the
carpet is brand new or very dirty, or if long-haired pets frequently
use the carpeted area. Unplug cleaner and examine several
areas on the power nozzle to see if debris has built up:
a. Replace the squeegee by first inserting one tab on the squeegee
end with the slot on nozzle. Then insert the tab located on other
end of squeegee into the nozzle slot.
NOTE: Turn the squeegee upside down for storage. The
squeegee is designed to assist in hard floor cleaning,
however, it can be left on for carpet cleaning.
a. Extractor slots
b. Brush roll chamber
c. Spray Tips
fig. 20 To clean the Steemer extractor slots, place a cloth or towel over
the motor cover to shield and protect the motor from water
damage. Run hot tap water through the nozzle until clean.
To clean the brush chamber and spray tips, take a towel or damp
cloth and wipe clean.
To Store Cleaner
fig. 6 Pull the wheel assembly forward toward nozzle for compact
storage.
NOTE: Do not store the cleaner in freezing conditions.
Do not store the cleaner with water in the tank. Do not store
the cleaner with cleaner cartridge attached. Turn the
squeegee upside down for storage. Squeegee will deform if
left in position while in storage.
Things To Do
•
•
•
•
•
Use only manufacturer recommended attachments and accessories.
Keep free of dust, lint, and hair.
Turn off all controls before unplugging.
Test the A.L.C.I. plug with every use.
Empty the recovery tank when full and whenever clean water is
added to the supply tank.
•
•
•
Keep young children and pets away from cleaned carpets until dry.
Check carpets and upholstery for color fastness.
Clean nozzle periodically.
To Replace Belt
WARNING: To reduce the risk of electric shock or injury from
moving parts, unplug before servicing.
Replacement belts (Part No. OR114) for Oreck Steemers are available
from Oreck. Call Toll-Free 1-800-989-3535.
fig. 4 Unplug the power cord leading from the power head to the rear
of the main cleaner.
fig. 3 Remove the power nozzle from the main cleaner.
fig. 21 Disassemble Power Nozzle:
a. Remove screw from belt cover.
b. Remove two (2) screws holding the brush roll clamp in place and
remove clamp.
© 2002 Oreck Holdings, LLC. All Rights Reserved. All word mark, logos, product configurations,
and registered trademarks are owned and used under the authorization of Oreck Holdings, LLC.
Printed in U.S.A.
7
53320-01 REV E 03/02 ECN# R-6359
|