INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Gable Fan
MODEL: GF1200N, GF900N
IMPORTANT SAFETY INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
(A) Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer.
MOUNTING
BRACKETS
(B) Before servicing or cleaning unit, switch power off at service
panel and lock service panel to prevent power from being
switched on accidentally.
When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to
the service panel.
CAUTION: For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
CAUTION: This unit has an unguarded impeller. Do not use in
locations readily accessible to people or animals.
FIGURE 1
INSTALLATION INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
(A) Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and
standards, including fire-rated construction.
(B) Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration, and Air
Conditioning Engineers (ASHRAE), and the local code
authorities.
(C) When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
FIGURE 2
(D) Ducted fans must always be vented to the outdoors.
(E) NEVER place a switch where it can be reached from a tub or
shower enclosure.
• READ INSTRUCTIONS CAREFULLY BEFORE PROCEEDING.
• WARNING: To reduce the risk of fire or shock do not use with solid
state speed control.
• This fan is intended for installation behind existing attic louvers.
SPECIFICATIONS: Thermally protected motor operates on 115vAC,
60 cycle. Large 14" fan blade, 15 inch diameter shroud.
ASSEMBLING THE UNIT
Refer to Figure 1.
Using provided hardware attach the mounting brackets to the unit.
MOUNTING THE UNIT
FIGURE 3
Refer to Figure 2.
• Secure unit to structure inside the attic.
• 2" x 4" wall studs may be modified to allow for proper spacing.
• Cover remaining area of louver. (See Figure 3)
MOUNTING THE THERMOSTAT
Refer to Figure 2.
Mount the thermostat to a nearby rafter using screws
(not provided) through the mounting tabs.
Important: For every 300 CFM of fan performance, a minimum of one
square foot of inlet space is necessary for proper operation. Air inlet
area should be located as far from fan location as possible.
EFFECTIVE
DATE
PRODUCT
GROUP
MODEL NUMBER
PARTS LIST
GF-1200N,
GF-900N
OCTOBER
1998
GABLE FAN
4
5
3
1
2
CURRENT
REPLACEMENT
PART NO.
ORIGINAL
REF.
PART DESCRIPTION
MODEL USED ON
PART NO.
87403
87406
0419B
87401
88007
87409
MOTOR
GF-900N
GF-1200N
GF-1200N
87403-000
1
MOTOR
87406-000
0419B-000
87401-000
88007-000
87409-000
2
3
4
5
CAPACITOR
BLADE
GF-1200N, GF900N
GF-900N, GF-1200N
GF-900N, GF-1200N
THERMOSTAT
CONDUIT
NuTone
Attn: Parts Department
4820 Red Bank Roads
®
Cincinnati, OH 45227-1599
Phone: (513) 527-5426
Fax: (513) 527-5173
NOTE: Always order by
current part number
GF-900N, GF-900N I.I.
|