BSR252_QIG_1.pdf 12/21/2006 10:24:58 AM
Step 8
Assign TCP/IP addresses
15
BusinBessSSec
R
ure2Rou
5
ter 252
2
15. From the first Wizard window, choose the type of encapsulation and service
that your ISP supplies. The wizard displays different windows for each type of
encapsulation and service.
8
8. Set up the IP addresses on each computer connected to the BSR252:
a. Set each computer to dynamically obtain an IP address, or assign unique static
IP addresses. If you choose to assign unique static IP addresses for each
computer, choose IP addresses between 192.168.1.129 and 192.168.1.254.
b. If you assign a static IP address in step 8a, assign a subnet mask of
255.255.255.0 and a default gateway of 192.168.1.1.
c. If you chose to dynamically obtain IP addresses in step 8a, you have an option
of using Obtain a DNS server address automatically, or assigning the DNS
server IP addresses.
Quick Install Guide
16. Depending on the type of encapsulation that your ISP
uses, enter the following information:
Detailed documentation for this Quick
Installation Guide can be downloaded at
16
Steps 1 4
Before you start
PPP over ADSL (PPPoA)
Enter the User Name and Password assigned by your ISP, and enter 100
seconds in the Idle Timeout field. Click the Nailed-Up Connection option to
keep the connection active. In the Network Address Translation list, select SUA
Only.
d. If you chose to assign unique static IP addresses in step 8a, you must assign
DNS Server IP addresses.
1. Contact your Internet Service Provider (ISP) to get the
following information:
RFC 1483
a. Encapsulation type
b. Multiplex Mode, VPI, VCI
1
Enter the IP Address and Password assigned by your ISP. In the Network
Address Translation list, select SUA Only.
Steps 9 12
Access the BSR252
c. ISP IP addresses: WAN, DNS servers, Gateway, and WAN
MAC address
ENET ENCAP (Ethernet)
If you have a dynamic WAN IP address, select Obtain an IP Address
Automatically; otherwise, select Static IP Address and type your ISP assigned
WAN IP address and the subnet mask in the fields provided. In the ENET
ENCAP Gateway field, enter the gateway IP address given by your ISP.
PPP over Ethernet (PPPoE)
2. Get your Domain Name from the User
Accounts dialog box in the Control Panel.
For details, see your operating system Help
files. Get your Computer Name from the
System Properties dialog box on your
computer.
9. In the address field of your browser, enter
192.168.1.1
2
9
Enter the Service Name, User Name and Password assigned by your ISP, and
enter 100 seconds in the Idle Timeout field. Click the Nailed-Up Connection
option to keep the connection active.
10. Enter the default
user name (nnadmin)
and password
(PlsChgMe!) to log
onto the BSR252.
10
C
M
3. (Optional) Get the IP addresses of DNS
Steps 17 18
Complete your configuration
and remote servers on your LAN.
3
Y
CM
MY
CY
CMY
K
InSstteapsll4th7e hardware
17. Review your settings.
11
11. You can replace the default password (recommended)
17
or use it as it is.
18. Click Save Settings.
12. Replace the factory-default
18
certificate.
12
4
4. Mount the
Steps 13 16
Steps 19 20
BSR252 on a wall,
Start the wizard
Testing your Internet
or place it
horizontally or vertically (using the supplied holder) on a flat surface.
connection
13
5. Connect your PC and up to three other
19
computers or network devices to the four
13. On the left
navigation pane,
click Wizard.
5
19. To confirm the ADSL
connection, click the
Start Diagnose button.
This test takes
Ethernet ports.
6. Connect your ADSL Internet service to the
telephone port next to the Power LED.
approximately 20
6
seconds. If this test fails,
confirm steps 1-18, and
contact your service
provider.
7. Snap the appropriate power clip
into the supplied power adapter.
Connect the power adapter to the rear
of the BSR252 and to an AC power
source.
7
14
20
14. In the General Setup window, enter the system name (your computer
20. Test your connection to the Internet by opening your browser and
name) and the domain name.
visiting a known Web site.
N0143490
|