NETGEAR Network Router MBR814 User Manual

d. Then connect the other end into the Ethernet port of your computer. (point C in  
3. THEN, CONNECT TO THE INTERNET.  
the diagram)  
a. Make sure that the blue light on the back of the broadband card is on.  
)NSTALLATION 'UIDE  
54 Mbps Mobile Broadband Router MBR814  
b. Check the Router Status page to make sure that wireless broadband coverage is  
available.  
c. Verify connectivity to the Internet by opening a browser or verify access to  
network resources such as files and printers.  
Broadband card  
in slot  
Start Here  
d. Make any needed configuration changes to fit your wireless local area network  
(WLAN) such as setting up wireless security.  
Before proceeding, familiarize yourself with the contents of the product package,  
especially the Reference Manual on the Resource CD and the animated tutorials on  
configuring computers for networking.  
C
Note: For details about security settings, and wireless configuration, see the  
Reference Manual on the Resource CD.  
B
A
Minimum Requirements  
The MBR814 is now connected to the Internet and to your WLAN.  
The MBR814 is designed for easy installation. Make sure that these minimum  
requirements are met.  
LAN port 4  
Internet  
e. Plug in the power adapter to your router. Verify the following:  
You must have an account for wireless broadband service, and you must be located in  
an area with wireless broadband coverage. Check with your Internet service provider  
if you are not sure.  
WLAN  
The power light is lit after applying power to the router.  
Your computer must have an available Ethernet port to connect to the MBR814  
during installation and setup.  
The Status light comes on briefly and then goes off.  
2. NEXT, CONNECT TO THE ROUTER.  
Observe the guidelines for placement of wireless equipment as described in the  
Reference Manual on the Resource CD.  
a. Turn on your computer, let the operating system boot up completely, and log in as  
needed.  
Your computer must have a wireless adapter or wireless card that is set up to run on  
your network; and it must be configured with DHCP.  
b. The light on the router for the port connected to the computer lights up.  
c. From the Ethernet connected computer you just set up, open a browser such as  
Internet Explorer or Netscape® Navigator.  
Technical Support  
1. FIRST, INSTALL THE ROUTER.  
d. Connect to the router by typing http://192.168.0.1 in the address field of your  
a. Turn off your computer.  
Please contact your Internet Service Provider for technical support.  
browser.  
b. Check the router to make sure that the broadband card is securely inserted in the  
By registering your product at http://www.NETGEAR.com/register, we can provide you  
with timely expert technical support.  
slot as shown in point A in the diagram.  
c. Connect the Ethernet cable that came with your router into a LAN port on the  
router such as LAN port 4 (point B in the diagram).  
e. When prompted, enter admin for the user name and password for the password,  
both in lower case letters. After logging in you will see the router menu.  
© 2005 by NETGEAR, Inc. All rights reserved. NETGEAR is a registered trademark of NETGEAR, Inc. in the  
United States and/or other countries. Other brand and product names are trademarks or registered trademarks of  
their respective holders. Information is subject to change without notice.  
 

Miele Coffeemaker CVA 2660 User Manual
Milwaukee Sander 6080 20 User Manual
Mr Coffee Coffeemaker ES10 User Manual
Multiquip Portable Generator ga 97HE User Manual
NEC Computer Monitor R 37 Xtra User Manual
NEC Computer Monitor V422 User Manual
NETGEAR Network Card XM128U User Manual
Nortel Networks Computer Hardware 5380 User Manual
NuTone Ventilation Hood NS6500 Series User Manual
Panasonic Cell Phone 6275I User Manual