Contents
Unpacking Your New Router .............................................................................................1
Hardware Features ............................................................................................................2
Router Front Panel ......................................................................................................2
Router Back Panel ......................................................................................................4
Router Label ................................................................................................................5
Positioning Your Wireless Router ......................................................................................5
Installing Your Wireless Modem Router ............................................................................6
Installing Your Router Using the
Using the Smart Wizard .....................................................................................................8
Accessing Your Router After Installation ...........................................................................9
Upgrading the Router Firmware ......................................................................................10
Installing Your Router Manually
Understanding ADSL Microfilters ....................................................................................12
ADSL Microfilter ........................................................................................................12
ADSL Microfilter with Built-In Splitter ........................................................................12
Connecting Your Wireless Modem Router ......................................................................13
Verifying Your Connection ...............................................................................................16
Setting Up Your Router for Internet Access ....................................................................17
Setting Your SSID and Wireless Security ........................................................................20
Using Push 'N' Connect (WPS) to Add Wireless Devices ...............................................21
Basic Functioning ............................................................................................................23
Power LED Not On ....................................................................................................24
iii
Power LED is Red .....................................................................................................24
LAN or Internet Port LEDs Not On ............................................................................24
Troubleshooting the Web Configuration Interface ...........................................................25
Troubleshooting the ISP Connection ...............................................................................26
ADSL link ..................................................................................................................26
Obtaining an Internet IP Address ..............................................................................27
Troubleshooting PPPoE or PPPoA ...........................................................................28
Troubleshooting Internet Browsing ...........................................................................28
Troubleshooting a TCP/IP Network Using the Ping Utility ...............................................29
Testing the LAN Path to Your Router ........................................................................29
Restoring the Default Configuration and Password .........................................................30
General Specifications .....................................................................................................31
Default Configuration .......................................................................................................32
iv
Getting to Know Your Wireless Router
Congratulations on your purchase of a NETGEAR® high-speed wireless router, the Wireless-N
150 ADSL2+ Modem Router.
Before you begin installing your router, check the package contents (see “Unpacking Your New
Router” on page 1). Become familiar with the front and back panels of your router—especially the
selected the best location to install your router.
This chapter describes how to set up the wireless modem router on your Local Area Network
(LAN) and connect to the Internet. It describes how to set up your wireless modem router for
Internet access and configure basic wireless connectivity.
Unpacking Your New Router
Your router should contain the following items:
•
•
•
•
•
•
Wireless-N 150 ADSL2+ Modem Router
AC power adapter (varies by region)
Category 5 (Cat 5) Ethernet cable
Telephone cable with RJ-11 connector
Microfilters (quantity and type vary by region)
Resource CD, including:
–
–
–
The Smart Wizard Installation Assistant
This manual
Warranty and Support Information
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
Place your router in a suitable area for installation (near an AC power outlet and accessible to the
Ethernet cables for your wired computers).
Getting to Know Your Wireless Router
1
Hardware Features
Before you install and connect your router, take a moment to become familiar with the front and
back panels of the router—especially the LEDs on the front panel.
Router Front Panel
The wireless modem router front panel shown below contains status LEDs.
LAN Ports (1-4)
Power
WPS
DSL
Wireless
Internet
Figure 1
Getting to Know Your Wireless Router
2
Table 1.
LED Descriptions
LED Activity
Label
Description
Power
Solid Green
Solid Red
Off
Power is supplied to the router.
POST (Power-On Self-Test) failure or device malfunction
Power is not supplied to the router
Factory reset
Lights momentarily when the reset button is pressed for 6 seconds,
then blinks red three times when released. It then turns green as the
gateway resets to the factory defaults.
LAN Ports
1 - 4
Solid Green
Blinking Green
Off
The Local port has detected an Ethernet link with a device.
Data is being transmitted or received.
No link is detected on this port.
DSL
Solid Green
Blinking Green
Off
The ADSL port is synchronized with an ISP’s network-access device.
Indicates ADSL training—ADSL is synchronizing with the DSLAM.
The unit is off or there is no IP connection.
Internet Port Solid Green
There is an Internet session. If the session is dropped due to an idle
timeout, and an ADSL connection is still present, the light will remain
green. If the session is dropped for any other reason, the light will
turn off.
Solid Red
IP connection failed (no DHCP or PPoE response, PPPoE
authentication failed, etc.)
Blinking Green
Off
Data is being transmitted over the ADSL port.
No Internet connection detected or device in bridged mode.
Wireless
WPS
Solid Green
Blinking Green
Off
Indicates that the Wireless port is initialized.
Data is being transmitted or received over the wireless link.
The Wireless Access Point is turned off.
Solid Green
Blinking Green
Off
Indicates that wireless security has been enabled.
WPS-capable device is connecting to the device.
WPS has not been set or enabled.
Getting to Know Your Wireless Router
3
Router Back Panel
The back panel of the wireless modem router contains port connections.
3
4
1
2
Figure 2
Viewed from left to right, the rear panel contains the following elements:
1. RJ-11 ADSL port for connecting the wireless modem router to an ADSL line
2. Four Local Ethernet RJ-45 LAN ports for connecting the wireless modem router to the local
computers
3. Power On/Off button
4. AC power adapter input
Getting to Know Your Wireless Router
4
Router Label
The label on the bottom of the wireless modem router shows the router’s MAC address, serial
number, security PIN, and factory default login information.
Factory Default Reset. Press for 6 seconds to reset the router
to its factory default settings.
Figure 3
Positioning Your Wireless Router
The wireless modem router lets you access your network from virtually anywhere within the
operating range of your wireless network. However, the operating distance or range of your
wireless connection can vary significantly depending on the physical placement of your router. For
example, the thickness and number of walls the wireless signal must pass through may limit the
range. For best results, place your router:
•
Near the center of the area where your computers and other devices will operate, preferably
within line of sight to your wireless devices.
•
•
Accessible to an AC power outlet and near Ethernet cables for wired computers.
In an elevated location such as a high shelf, keeping the number of walls and ceilings between
the wireless modem router and your other devices to a minimum.
•
Away from electrical devices which are potential sources of interference, such as ceiling fans,
home security systems, microwaves, or the base for a cordless phone.
Getting to Know Your Wireless Router
5
•
Away from any large metal surfaces, such as a solid metal door or aluminum studs. Large
expanses of other materials such as glass, insulated walls, fish tanks, mirrors, brick, and
concrete can also affect your wireless signal.
Failure to follow these guidelines can result in significant performance degradation
or an inability to wirelessly connect to the Internet.
Installing Your Wireless Modem Router
To help you set up your router and get on the Internet quickly, the Resource CD contains a Smart
Wizard™. The Smart Wizard walks you through the steps required to connect your router,
microfilters, and PC(s); configure your wireless settings; and enable wireless security for your
network. When you have finished, you will be Internet ready!
If you have a Macintosh or Linux system, you need to use the manual installation
You can set up your wireless modem router using one of two methods:
•
Smart Wizard Setup: The Smart Wizard setup is available on your Resource CD. See
“Installing Your Router Using the Smart Wizard” on page 8 to use the Smart Wizard.
–
–
This is the easiest option. The wizard guides you through the setup process. It automates
many of the steps and verifies that the steps have been successfully completed.
Smart Wizard requires a PC running Microsoft Windows..
Before running the Smart Wizard on a corporate PC to set up your home
router, check with your company’s network support staff. Corporate
network settings or Virtual Private Network (VPN) client software may
conflict with the default settings of a home router. If you are unsure about
whether there might be a conflict, use a different computer.
•
Router Manually (Advanced, Mac, and Linux Users)” on page 11. For example, if you are
connecting to a Mac, are using a Linux operating system, or are technically knowledgeable,
select this option.
Getting to Know Your Wireless Router
6
If you choose to use the manual setup option, for best results, install and set up your router in
this order:
3. Configure your wireless network and select wireless security settings to protect your
Getting to Know Your Wireless Router
7
Installing Your Router Using the
Smart Wizard
To use the Smart Wizard, you must be using a PC with Microsoft Windows 7, Windows Vista,
Windows XP, or Windows 2000 with Service Pack 2. The Smart Wizard setup procedure should
take about 15 minutes to complete. Before using the Smart Wizard to set up your wireless modem
router, ensure that:
•
•
You have an ADSL Internet service connection through an Internet Service Provider (ISP).
You have the configuration information provided by your ISP.
Using the Smart Wizard
The NETGEAR Smart Wizard takes you through the procedure to connect your router, ADSL
microfilters, and PC(s). It then helps you to configure your wireless settings and enable wireless
security for your network. The Smart Wizard guides you through the setup process by automating
many of the steps. At each step in the setup process, the Smart Wizard checks to ensure that the
steps you perform are successfully completed.
To install your router using the Smart Wizard:
1. Locate the ADSL settings information provided by your Internet Service Provider.
2. Insert the Resource CD into your Windows PC. The CD will automatically start and detect the
language you are using on your PC. Select a different language option, if you prefer.
If the CD does not automatically start, browse the CD and double-click on
.
3. When the Welcome screen appears, click Setup to start the Smart Wizard. Follow the
instructions and prompts to complete the installation.
8
The Smart Wizard guides you through installing your router, connecting your router to the
Internet, configuring your wireless network settings, and selecting the optimum security
protection for your network. If you choose not to select a security option during installation,
you can always access the router’s user interface later to select a security option (see
To ensure optimum performance of your high-speed wireless router, the
wireless adapter card for each computer in your network should support the
same technology as your router (see the online User Manual for more
information).
You are now connected to the Internet!
To set up additional wireless computers in your network for router access and to connect to the
Accessing Your Router After Installation
The Smart Wizard only appears when you first install the router or when the router is in its factory
default state (for example, if you have reset the router to its factory default settings). If you want to
change the settings after installing and configuring your router, you can click the desktop
shortcut—a preconfigured shortcut
placed on your desktop at installation—to open the
router management interface.1 Optionally, you can also open a browser window and log in to the
router. After logging in, you can:
•
Set up other wireless computers on your network, see “Configuring Your Wireless Network”
•
Change settings and configure wireless security, see “Setting Your SSID and Wireless
For advanced features that are not covered in this manual, see the User Manual on your Resource
CD. A link to the on-line User Manual also is available from the router interface.
1. The shortcut icon is installed on your desktop only when using the Smart Wizard installation method.
Installing Your Router Using the Smart Wizard
9
Upgrading the Router Firmware
When you run the Resource CD you will have an opportunity to upgrade to the latest available
firmware. Once you have configured your wireless-N modem router, when you log in to the
wireless-N modem router the Firmware Upgrade Assistant screen displays.
1. Click Yes to check for new firmware (recommended). The wireless-N modem router
automatically checks the NETGEAR database for a new firmware image file. If no new
firmware version is available, the message “No New Firmware Version Available” displays.
(If you select “No,” you can check for new firmware later; see the online User Manual).
2. If new firmware is available, click Yes, and the router automatically upgrades itself with the
latest firmware.
Do not try to go online, turn off the router, shut down the computer, or do
anything else to the router until the router finishes restarting and the Ready light
has stopped blinking for several seconds!
Installing Your Router Using the Smart Wizard
10
Installing Your Router Manually
(Advanced, Mac, and Linux Users)
Before installing and connecting your router manually, review the list below and make sure that
you have all of the necessary information.
•
•
Internet ADSL service connection through an Internet Service Provider (ISP).
The configuration information your ISP gave you. Depending on how your Internet account
was set up, you may need the following information to set up your wireless modem router and
access the Internet:
–
–
–
–
Host and Domain Name
Internet Login Name and Password (frequently an email address and password)
Domain Name Server (DNS) Addresses
Fixed or Static IP Address
Your ISP should have provided you with all the information needed to connect to the Internet.
If you cannot locate this information, ask your ISP.
•
•
Your computers set to DHCP enabled.
If you have not already done so:
•
Check the package contents of your router to ensure that it is complete (see “Unpacking Your
•
Select an optimum location for your wireless modem router after reviewing the guidelines
Installing Your Router Manually (Advanced, Mac, and Linux Users)
11
Understanding ADSL Microfilters
ADSL technology uses the same wires as your telephone service. However, ADSL adds signals to
the telephone lines which create noise in the telephone service. You must use ADSL microfilters
to filter out these signals before they reach your telephone.
If you purchased the wireless modem router in a country where a microfilter is not
included, you must acquire one.
ADSL Microfilter
Figure 4
Each device such as a telephone, fax machine, answering machine, or caller ID display will require
an ADSL microfilter.
Do not connect the wireless modem router to the ADSL line through a microfilter
unless the microfilter is a combination microfilter/splitter specifically designed for
this purpose. Doing so will prevent block your connection to the Internet. If you
have any doubts about this, connect the wireless modem router directly to the
ADSL line.
ADSL Microfilter with Built-In Splitter
Use an ADSL microfilter with built-in splitter when there is a single wall outlet which must
provide connectivity for both the wireless modem router and telephone equipment.
Figure 5
Installing Your Router Manually (Advanced, Mac, and Linux Users)
12
Connecting Your Wireless Modem Router
Before you install your wireless modem router, make sure that the Internet Protocol (TCP/IP)
Property settings on your computer are set to “automatically obtain an IP address” using DHCP
and “Obtain DNS server address automatically.” You can check these settings by looking at the
TCP/IP Properties of your Internal Network Connections, which are accessible through the
Control Panel of your computer. If you are unsure about this, refer to the documentation for your
If you are replacing an existing router, disconnect it completely from your network
and set it aside before starting to install your new router.
To connect the wireless modem router, the ADSL filter and the computer:
1. Connect an ADSL filter as shown below.
If you purchased the DGN1000 in a country where an ADSL filter is not
included, you must acquire one.
•
Install an ADSL filter for every telephone that uses the same phone line as your wireless
modem router. Select the appropriate filter(s) for your wireless setup.
1
2
3
1. One-Line Filter: Use with a phone or fax machine.
2. Splitter: Use with a one-line filter to share an outlet with a phone and the wireless
modem router.
3. Two-Line Filter with Splitter: Use to share an outlet with a phone and the wireless
modem router.
Figure 6
Installing Your Router Manually (Advanced, Mac, and Linux Users)
13
•
Two-Line Filter Example. Insert the two-line filter into the phone outlet and connect the
A
Figure 7
To use a one-line filter with a separate splitter, insert the splitter into the phone
outlet, connect the one-line filter to the splitter, and connect the phone to the
filter.
2. Connect the wireless modem router to the ADSL filter. Using the included phone cable with
RJ-11 jacks, connect the ADSL port (B) of the wireless modem router to the ADSL port (C) of
Installing Your Router Manually (Advanced, Mac, and Linux Users)
14
.
B
C
Figure 8
Improperly connecting a filter to your wireless modem router will block
your ADSL connection.
3. Connect the Ethernet cable (D) from a wireless modem router LAN port to the Ethernet
4. Connect the power adapter to the wireless modem router and plug it in to a power outlet.
Installing Your Router Manually (Advanced, Mac, and Linux Users)
15
D
D
Figure 9
5. Connect any additional wired PCs to your router by inserting an Ethernet cable from a PC into
one of the three remaining LAN ports.
Verifying Your Connection
Verify that your router is connected correctly by checking the wireless modem router status lights.
•
•
•
•
The power light is lit after turning on the wireless modem router.
The DSL light is lit, indicating an ADSL connection.
The wireless light is lit after turning on the wireless modem router.
The Internet light is green, indicating you are connected to the ADSL network.
Now, turn on your computer. If software usually logs you in to your Internet connection, do not run
that software. Cancel it if it starts automatically. Verify the following:
•
The local lights (1 through 4) are lit for any connected computers.
Installing Your Router Manually (Advanced, Mac, and Linux Users)
16
Setting Up Your Router for Internet Access
When configuring your wireless router manually, you must log in to your wireless modem router
to set it up initially and to make any changes to your wireless router’s settings later.
To access the router:
You can also enter either of these addresses to connect to your wireless router:
.
Figure 10
Figure 11
2. When prompted, enter admintfor the router User Name and password for the router
Password, both in lowercase letters. (For security reasons, the router has its own user name
and password.)
The router user name and password are not the same as any user name or
password you may use to log in to your Internet connection.
The Main menu will display.
Installing Your Router Manually (Advanced, Mac, and Linux Users)
17
3. From the menu options in the left navigation pane, click Setup Wizard. The Setup Wizard
screen will display.
Figure 12
4. Select one of the following options:
•
Select Yes to allow the Setup Wizard to detect your Internet connection. When prompted,
click Next. The wizard will assist you with configuring your wireless router to access the
Internet.
If you cannot connect to the wireless router, check the Internet Protocol
(TCP/IP) properties in the Network Connections section of your Control
Panel. It should be set to obtain both IP and DNS server addresses
automatically. For assistance, see your computer documentation or see the
•
Select No to set up the connection yourself. Click Next and the Basic Settings screen will
display. Enter the required information for your ISP connection in the appropriate fields. If
you need assistance, follow the Basic Settings Help screens on the router interface or see
the online User’s Manual for this wireless modem router.
5. Click Apply to save your settings and complete your connection.
You should now be connected to the Internet!
If you do not connect successfully:
•
Review your settings and make sure that you have selected the correct options and typed
everything correctly.
•
•
Contact your ISP to verify that you have the correct configuration information.
If problems persist, register your NETGEAR product and contact NETGEAR Technical Support.
Installing Your Router Manually (Advanced, Mac, and Linux Users)
18
Configuring Your Wireless Network
After installing your router, you must log into the router to complete your wireless setup. The
wireless network settings of the router must match the wireless network settings of any wireless
devices that connect wirelessly to the router (such as wireless adapter cards and wireless
computers).
For a wireless connection, the router and each wireless computer must use the same SSID, also
called the wireless network name, and the same wireless security. NETGEAR strongly
recommends that you use wireless security.
Indoors, computers can connect over wireless networks at a range of several hundred
feet. This can allow others outside of your immediate area to access your network.
The Wireless Settings screen lets you set your wireless network connections and the wireless
security option for your network and router. To configure the wireless network, you can either
manually specify your network name (SSID) and your wireless security settings (see “Setting
Your SSID and Wireless Security” on page 20) or, if all of the clients in your network are WPS
capable, you can use Wi-Fi Protected Setup (WPS) to automatically configure your router and, at
Connect (WPS) to Add Wireless Devices” on page 21). You can also use Push 'N' Connect (WPS)
to add WPS-capable devices after you have set your SSID and wireless security using the manual
or traditional method (the preferred option).
If you configure the router from a wireless computer and you change the router’s
SSID, channel, or security settings, you will lose your wireless connection when
you click Apply. You must then change your computer’s wireless settings to match
the router’s new settings. To avoid this situation, you can use a computer that is
connected to the router with an Ethernet cable.
For a complete overview of all the security configurations that can be implemented on this router,
see the on-line User Manual. A link to the User Manual is on the Resource CD.
Configuring Your Wireless Network
19
Setting Your SSID and Wireless Security
To specify the wireless settings, you must know the following:
•
•
•
SSID. The default SSID for the router is NETGEAR.
The wireless mode (802.11g/b, or 802.11n) that each wireless adapter supports.
Wireless security option. NETGEAR strongly recommends that you use wireless security. To
successfully implement wireless security, check each wireless adapter to determine which
wireless security option it supports.
To set up basic wireless connectivity and wireless security on your router:
of admin and default password of password, or using whatever LAN address and password
you have set up.
You can also enter either of these addresses to connect to your wireless router:
2. On the main menu, select Wireless Settings to display the Wireless Settings screen.
Note that the default SSID is NETGEAR.
The SSID of any wireless adapters must match the SSID you configure in the
wireless modem router. If they do not match, you will not get a wireless
connection.
3. Set the Region. Select the region where the router is located.
4. Leave the wireless mode set to its default setting (you can fine tune the wireless mode later—
see the online User Manual).
5. Select your wireless Security Option and passphrase. NETGEAR recommends WPA/WPA2
(see your online User Manual for a complete explanation of the various security types that are
available).
6. Click Apply to save your changes.
Configuring Your Wireless Network
20
To set up your computers for wireless connectivity:
1. Configure the wireless settings of each computer or wireless adapter to have the same SSID
(wireless network name) as the router.
2. Check that the wireless adapter on each computer can support the mode and security option
that you selected. (If you have a question, see the online User Manual or review the settings
3. Check that the security settings on each wireless device match the security settings of the
router. For example, if you selected a security option requiring a passphrase, then the same
passphrase must be used for each wireless computer.
4. Check that each wireless computer has a wireless link and is able to obtain an IP address by
DHCP from the router.
For a Windows PC, go to the Control Panel and select Network Connections.
Check the Wireless Connections Properties and ensure that TCP/IP Properties
are set to Obtain an IP address automatically.
To access the Internet from any computer connected to your wireless modem router, launch a
browser such as Microsoft Internet Explorer or Mozilla Firefox. You should see the wireless
modem router’s Internet LED blink, indicating communication to the ISP.
Using Push 'N' Connect (WPS) to Add Wireless
Devices
If your wireless clients support Wi-Fi Protected Setup (WPS), you can use this feature to connect
the wireless client securely and easily to the router. Look for the
device.1
symbol on your client
NETGEAR’s Push 'N' Connect feature is based on the Wi-Fi Protected Setup
(WPS) standard. All other Wi-Fi-certified and WPS-capable products should be
compatible with NETGEAR products that implement Push 'N' Connect.
Configuring Your Wireless Network
21
You can use WPS in one of two ways:
•
If the router’s SSID and security option have already been set (see “Setting Your SSID and
Wireless Security” on page 20), a wireless device can be connected to your wireless network
quickly and simply by using WPS. In this case, the existing wireless settings are transmitted to
the WPS-capable device.
•
If the router’s wireless options have not yet been configured and security has not been enabled
(the router is in its default state), WPS automatically configures the SSID and wireless security
settings for the router and then transmits these settings to the wireless device, such as a
wireless PC.
The first method is explained here. For more information on the second method, see the User
Manual.
If your network consists of WPS capable devices and non-WPS capable devices, NETGEAR
suggests that you set up your wireless network and security settings first using the manual or
only for adding additional WPS capable devices.
If you choose to use WPS, WEP with shared-key authentication is not supported by
WPS.
To add a wireless device using WPS:
1. Press the WPS button on your router. The router will start transmitting its wireless settings.
You have 2 minutes to press a corresponding WPS button on your wireless device.
2. On your wireless device, either:
•
•
Press an external WPS button on the outside of the device or,
Open the WPS utility on the device and follow the instructions to connect using WPS.
The WPS LED on the router will continue to blink while the 2-minute window is open. When the
LED stops blinking it will return to solid green. (The LED will only turn off if no security has been
configured on the router.)
Then, to access the Internet, launch a browser (such as Microsoft Internet Explorer or Mozilla
Firefox) from the device. You should see the wireless modem router’s Internet LED blink,
indicating communication with the ISP.
For more information on setting up your wireless network and configuring your wireless security
settings, see the User Manual. A link to the online User Manual is on your Resource CD.
Configuring Your Wireless Network
22
Troubleshooting
This chapter gives information about troubleshooting your wireless modem router. After each
problem description, instructions are provided to help you diagnose and solve the problem. For the
common problems listed, go to the section indicated.
•
•
•
•
•
Is the router on?
Have I connected the router correctly?
I cannot access the router’s configuration with my browser.
I have configured the router but I can’t access the Internet.
Go to “Troubleshooting the ISP Connection” on page 26.
I cannot remember the router’s configuration password.
Go to “To restore the factory default configuration settings, press the reset button on the
bottom of the router following the steps below.” on page 30.
•
I want to clear the configuration and start over again.
Basic Functioning
After you turn on power to the router, the following sequence of events should occur:
page 2 for an illustration and explanation of the LEDs).
2. After approximately 1 minute, verify that:
a. The LAN port LEDs are lit for any local ports that are connected.
b. The ADSL Internet port LED is lit.
Troubleshooting
23
If a port’s LED is lit, a link has been established to the connected device. If any of these
conditions does not occur, refer to the appropriate following section.
3. If you enabled wireless security, verify that the Push 'N' Connect (WPS) LED is lit. (If no
security is enabled, the WPS LED should be off.)
Power LED Not On
If the Power and other LEDs are off when your router is turned on:
•
Make sure that the power cord is properly connected to your router and that the power supply
adapter is properly connected to a functioning power outlet.
•
Check that you are using the power adapter supplied by NETGEAR for this product.
If the error persists, you have a hardware problem and should contact technical support.
Power LED is Red
When the router is turned on, it performs a power-on self test. If the Power LED turns red after a
few seconds or at any other time during normal operation, there is a fault within the router. The
power LED also turns red when you depress the factory default reset push button, and blinks red 3
times when that button is released. However, in this case, the wireless modem router is working
normally.
If the power LED turns red to indicate a router fault:
•
Cycle the power to see if the router recovers.
If the power LED is still red one minute after power up:
•
•
Cycle the power to see if the router recovers.
Clear the router’s configuration to factory defaults. This will set the router’s IP address to
192.168.0.1. This procedure is explained in “To restore the factory default configuration
settings, press the reset button on the bottom of the router following the steps below.” on
page 30.
If the error persists, you might have a hardware problem and should contact technical support.
LAN or Internet Port LEDs Not On
If either the LAN LEDs or ADSL Internet LED do not light when the Ethernet connection is made,
check the following:
•
Make sure that the Ethernet cable connections are secure at the router and at the hub or
workstation.
Troubleshooting
24
•
•
Make sure that power is turned on to the connected hub or workstation.
Be sure you are using the correct cable: when connecting the ADSL port, use the cable that
was supplied with the wireless modem router. If the Internet LED is still off, this may mean
that there is no ADSL service or the cable connected to the ADSL port is bad.
Troubleshooting the Web Configuration Interface
If you are unable to access the router’s Web Configuration interface from a computer on your local
network, check the following:
•
If you are using an Ethernet-connected computer, check the Ethernet connection between the
computer and the router as described in the previous section.
•
Make sure your computer’s IP address is on the same subnet as the router. If you are using the
recommended addressing scheme, your computer’s address should be in the range of
computer’s IP address.
•
•
•
If your computer’s IP address is shown as 169.254.x.x:, it might because recent versions of
Windows and MacOS generate and assign an IP address if the computer cannot reach a DHCP
server. These auto-generated addresses are in the range of 169.254.x.x. If your IP address is in
this range, check the connection from the computer to the router and reboot your computer.
If your router’s IP address was changed and you do not know the current IP address, clear the
router’s configuration to factory defaults. This will set the router’s IP address to 192.168.0.1.
This procedure is explained in “To restore the factory default configuration settings, press the
reset button on the bottom of the router following the steps below.” on page 30.
Make sure your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet
Explorer, click Refresh to be sure the Java applet is loaded.
•
•
Try quitting the browser and launching it again.
Make sure you are using the correct login information. The factory default login name is
admin and the password is password. Make sure that CAPS LOCK is off when entering this
information.
If the router does not save changes you have made in the Web Configuration Interface, check the
following:
•
When entering configuration settings, be sure to click the Apply button before moving to
another menu or tab, or your changes are lost.
Troubleshooting
25
•
Click the Refresh or Reload button in the Web browser. The changes may have occurred, but
the Web browser may be caching the old configuration.
Troubleshooting the ISP Connection
If your router is unable to access the Internet, you should check the ADSL connection, then the
Internet TCP/IP connection.
ADSL link
If your router is unable to access the Internet, you should first determine whether you have an
ADSL link with the service provider. The state of this connection is indicated with the Internet
LED.
Internet LED Green or Blinking Green
If your Internet LED is green or blinking green, then you have a good ADSL connection. You can
be confident that the service provider has connected your line correctly and that your wiring is
correct.
Internet LED Red
If the Internet LED is red, disconnect all telephones on the line. If this solves the problem,
reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the
microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green Internet LED, there may be a problem with
your wiring. If the telephone company has tested the ADSL signal at your Network Interface
Device (NID), then you may have poor quality wiring in your house.
Internet LED Off
If the Internet LED is off, disconnect all telephones on the line. If this solves the problem,
reconnect the telephones one at a time, being careful to use a microfilter on each telephone. If the
microfilters are connected correctly, you should be able to connect all your telephones.
If disconnecting telephones does not result in a green Internet LED the problem may be one of the
following:
•
Check that the telephone company has made the connection to your line and tested it.
Troubleshooting
26
•
Verify that you are connected to the correct telephone line. If you have more than one phone
line, be sure that you are connected to the line with the ADSL service. It may be necessary to
use a swapper if you ADSL signal is on pins 1 and 4 of the RJ-11 jack. The N150 Router uses
pins 2 and 3.
Obtaining an Internet IP Address
If your wireless modem router is unable to access the internet, and your Internet LED is red, you
should determine whether the wireless modem router is able to obtain a Internet IP address from
the ISP. Unless you have been assigned a static IP address, your wireless modem router must
request an IP address from the ISP. You can determine whether the request was successful using
the browser interface.
To check the Internet IP address from the browser interface:
2. Access the Main Menu of the wireless modem router’s configuration at
3. Under Maintenance, select Router Status and check that an IP address is shown for the
Internet port. If 0.0.0.0 is shown, your wireless modem router has not obtained an IP address
from your ISP.
If your router is unable to obtain an IP address from the ISP, the problem may be one of the
following:
•
If you have selected a login program, you may have incorrectly set the Service Name, User
•
Your ISP may check for your computer's host name.
Assign the computer Host Name of your ISP account to the wireless modem router in the
browser-based Setup Wizard.
•
Your ISP only allows one Ethernet MAC address to connect to Internet, and may check for
your computer’s MAC address. In this case:
–
Inform your ISP that you have bought a new network device, and ask them to use the
router’s MAC address; or
–
Configure your router to spoof your computer’s MAC address. This can be done in the
Basic Settings menu. Refer to the online help in the wireless modem router main menu.
Troubleshooting
27
Troubleshooting PPPoE or PPPoA
The PPPoE or PPPoA connection can be debugged as follows:
2. Under Maintenance, select Router Status.
3. Click Connection Status.
If all of the steps indicate “OK” then your PPPoE or PPPoA connection is up and working.
If any of the steps indicates “Failed”, you can attempt to reconnect by clicking Connect. The
wireless modem router will continue to attempt to connect indefinitely.
If you cannot connect after several minutes, you may be using an incorrect service name, user
name, or password. There also may be a provisioning problem with your ISP.
Unless you connect manually, the wireless modem router will not authenticate using
PPPoE or PPPoA until data is transmitted to the network.
Troubleshooting Internet Browsing
If your wireless modem router can obtain an IP address but your computer is unable to load any
Web pages from the Internet:
•
Your computer may not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www addresses)
to numeric IP addresses. Typically your ISP will provide the addresses of one or two DNS
servers for your use. If you entered a DNS address during the wireless modem router’s
configuration, reboot your computer and verify the DNS address as described in “Preparing
Your Network” on page 34. Alternatively, you can configure your computer manually with
DNS addresses, as explained in your operating system documentation.
•
Your computer may not have the wireless ADSL modem router configured as its TCP/IP
default gateway.
If your computer obtains its information from the wireless modem router by DHCP, reboot the
computer and verify the wireless modem router address as described in “Preparing Your
Troubleshooting
28
Troubleshooting a TCP/IP Network Using the Ping
Utility
Most TCP/IP terminal devices and routers contain a ping utility that sends an echo request packet
to the designated device. The device then responds with an echo reply. Troubleshooting a TCP/IP
network is made easy by using the ping utility in your computer.
Testing the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up
correctly.
To ping the router from a PC running Windows 95 or later:
1. From the Windows toolbar, click the Start button and select Run.
2. In the field provided, type Ping followed by the IP address of the router, as in this example:
ping 192.168.0.1
3. Click OK.
You should see a message like this one:
Pinging <IP address> with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
–
–
Check that the corresponding Link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and router.
•
Wrong network configuration
–
Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your PC or workstation.
Troubleshooting
29
–
Verify that the IP address for your router and your workstation are correct and that the
addresses are on the same subnet.
Testing the Path from Your Computer to a Remote Device
After verifying that the LAN path works correctly, test the path from your PC to a remote device.
From the Windows run menu, type:
PING -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section are displayed. If you do not
receive replies:
•
Check that your PC has the IP address of your router listed as the default gateway. If the IP
configuration of your PC is assigned by DHCP, this information will not be visible in your
PC’s Network Control Panel. Verify that the IP address of the router is listed as the TCP/IP
•
•
Check to see that the network address of your PC (the portion of the IP address specified by
the netmask) is different from the network address of the remote device.
If your ISP assigned a host name to your PC, enter that host name as the Account Name in the
Basic Settings menu.
Restoring the Default Configuration and Password
This section explains how to restore the factory default configuration settings, changing the
router’s administration password to password and the IP address to 192.168.0.1. You can erase
the current configuration and restore factory defaults by pressing the reset button on the bottom of
the router. Use this method for cases when the administration password or IP address is not known.
To restore the factory default configuration settings, press the reset button on the bottom of the
router following the steps below.
1. Press and hold the reset button until the Power LED blinks red (about 6 seconds).
2. Release the reset button and wait for the router to reboot.The Power LED will blink red three
times and then will turn green when the default configuration settings have been restored.
Troubleshooting
30
Technical Specifications
This appendix provides technical specifications for the wireless modem router.
General Specifications
Network Protocol and Standards Compatibility
Data and Routing Protocols:
TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged
or Routed Ethernet, and RFC 1577 Classical IP over ATM
Power Adapter
North America:
UK, Australia:
Europe:
120V, 60 Hz, input
240V, 50 Hz, input
230V, 50 Hz, input
12 V AC @ 1.0A output
All regions (output):
Physical
Dimensions:
6.80" x 5.03" x 1.28"
172.7 mm x 127.7 mm x 32.5 mm
Weight:
0.61 lbs.
0.275 kg
Environmental
Operating temperature:
Operating humidity:
Storage temperature:
Storage humidity:
0 to 40 C (32º to 104º F)
10% to 90% relative humidity, noncondensing
-20 to 70 C (-4º to 158º F)
5 to 95% relative humidity, noncondensing
Regulatory Compliance
Meets requirements of:
FCC Part 15 Class B; VCCI Class B; EN 55 022 (CISPR 22), Class B
Technical Specifications
31
Interface Specifications
LAN:
10BASE-T or 100BASE-Tx, RJ-45
WAN:
ADSL, Dual RJ-11, pins 2 and 3
T1.413, G.DMT, G.Lite
Default Configuration
on page 30. Your router will return to the factory configuration settings that are shown in the table
below.
Feature
Default Behavior
Router Login
User Login URL
User Name (case sensitive)
admin
Login Password (case sensitive)
password
Internet Connection
WAN MAC Address
WAN MTU Size
Port Speed
Use Default address
1492
AutoSense
Local Network (LAN)
Lan IP
192.168.0.1
255.255.255.0
None
Subnet Mask
RIP Direction
RIP Version
Disabled
None
RIP Authentication
DHCP Server
DHCP Starting IP Address
DHCP Ending IP Address
DMZ
Enabled
192.168.0.2
192.168.0.254
Disabled
GMT
Time Zone
Technical Specifications
32
Feature
Default Behavior
Time Zone Adjusted for Daylight Saving Disabled
Time
SNMP
Disabled
Firewall
Inbound (communications coming in from Disabled (except traffic on port 80, the http port)
the Internet)
Outbound (communications going out to Enabled (all)
the Internet)
Source MAC filtering
Wireless
Disabled
Wireless Communication
SSID Name
Enabled
NETGEAR
Disabled
Enabled
Autoa
Security
Broadcast SSID
Transmission Speed
Country/Region
United States (in North America; otherwise, varies by
region)
RF Channel
Operating Mode
Data Rate
Auto
Up to 130 Mbps
Best
Output Power
Full
Access Point
Enabled
Authentication Type
Wireless Card Access List
Open System
All wireless stations allowed
a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary.
Network conditions and environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate.
Technical Specifications
33
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
ITCP/IP Networking Basics
Wireless Networking Basics
Preparing Your Network
Virtual Private Networking Basics
Glossary
Related Documents
34
Registration and Certifications
Product Registration, Support, and Documentation
Register your product at http://www.NETGEAR.com/register. You must register before you can use our telephone
support service. Product updates and Web support are always available by going to: http://kbserver.netgear.com/.
Setup documentation is available on the CD, on the support website, and on the documentation website. When the
wireless modem router is connected to the Internet, click the KnowledgeBase link to view support information or click
the Documentation link to view the online User Manual for this wireless modem router.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
35
|