Installation Instructions
ESW 47xx
ESW 48xx en_CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Installation
Installation tips
Steam from the vents can damage
the cabinetry surrounding the
warming drawer.
– The warming drawer should be
placed at a convenient height for
easy access.
– The drawer should be installed clear
of drafts caused by open doors and
windows.
Solo Installation:
A minimum gap of 2" (5 cm) must be
present between the upper edge of
the warming drawer and the
cabinetry.
– Proper clearance must be allowed
for the warming drawer to open with
out interference.
Installation in combination with an
oven:
A minimum gap of 1" (2.5 cm) must
be present between the upper edge
of the warming drawer and the oven.
– The warming drawer must be
secured to cabinetry to prevent the
drawer from tipping when loaded.
– The warming drawer should be level
to prevent the drawer from sliding
open or closing on its own.
This gap should be sealed with a
moisture resistant sealing material.
The drawer cannot be leveled after it
has been installed.
If necessary install a shelf within the
cabinetry to support the drawer.
26
Installation
Dimensions for Solo Installation
ESW 47x0
a Material must be moisture resistant
Miele appliances can be installed ꢀush or proud. Discuss your
installation requirements with you architect, designer and installer.
27
Installation
ESW 48x0
a
24"
(610)
281/2"
26"-
(660-724)
2"
1/8"
10
15/16"
( 2 8 0 )
1
25
(659)
3
9
22 15/16"
(582)
13/16"
29
(757)
1"
(26)
a Material must be moisture resistant
28
Installation
Dimensions for a combination installation with an oven
ESW 47x0
a Material must be moisture resistant
1
7
( 5 8 0 )
( 5 9 6 )
23
a
1/8"
1
1
1
1
1
( 2 8 0 )
10
3/8"
3/16"
29
Installation
ESW 48x0
a Material must be moisture resistant
30
Installation
Installing the warming drawer
^ Push the casing in the cabinetry.
^ Remove the drawer from the casing
before installing the appliance into
the cabinetry.
Removing the drawer
^ Secure the casing in the cabinetry
with the six screws.
Inserting the drawer
^ Pull out the telescopic skis from the
casing.
^ Pull the drawer completely out and
loosen the nuts.
^ Set the drawer on the telescopic skis
and secure with the two nuts.
^ Carefully lift the drawer and pull it
slowly out.
Set the drawer down on a flat, stable
surface.
31
Installation
Integrated installations
Models 4700 FB and 4800 FB
a Install a handle to the custom front
panel using counter sunk screws.
b Remove the drawer from the casing.
Custom made front panels can be
installed with models 4700 FB and
4800 FB.
See "Removing the drawer".
The panel attached to the warming
drawer front can be used as the drilling
template for the custom panel.
Panel dimensions
4700 FB
Width 27 3/8" (695 mm)
Height 11" (279 mm)
4800 FB
Width 29 13/16" (757mm)
Height 11" (279 mm)
The custom panel must be atleast 3/8"
(10 mm) thick and made of heat resist-
ant material140 °F (60 °C).
c Loosen the two screws on the inner
side of the drawer and remove the
panel from the appliance front.
d Place the panel on a firm surface
with the adhesive tape facing up.
Peel the backing from the adhesive
tape.
e Position the custom panel over the
removed panel using the tape to hold
it in place.
32
Installation
f Press the custom panel tightly onto
h Hook the panels into the bottom on
and secure at the top with two
screws making sure the seal is
seated correctly.
the removed panel.
g Screw the removed panel to the
custom panel with the eight screws.
33
Alteration rights reserved / 3206
M.-Nr. 06 543 320 / 06
en - US
|