Miele Cooktop KM 5753 User Manual

Operating and Installation

Instructions

Ceramic Cooktop with Induction

KM 5753

KM 5758

en - US, CA

To prevent accidents and

appliance damage,

read these instructions

before

installation or use.

M.-Nr. 06 766 201

Contents

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Technical Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Installation dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Installing the cooktop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Help protect our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

IMPORTANT SAFETY INSTRUCTIONS

READ THE OPERATING

INSTRUCTIONS CAREFULLY

BEFORE USING THE

COOKTOP

Installation

Be certain your appliance is

properly installed and grounded by a

qualified technician in accordance with

national and local safety regulations.

WARNING -

Do not connect the appliance to the

main electrical supply using an

extension cord. Extension cords do not

meet the safety requirements of this

appliance.

This appliance is intended for

residential cooking only.

When using your appliance follow

basic safety precautions including

the following:

Before servicing, disconnect the

appliance from the main power supply.

To guarantee the electrical safety of

this appliance, continuity must exist

between the appliance and an effective

grounding system. It is imperative that

this basic safety requirement be met. If

there is any doubt, have the electrical

system of the house checked by a

qualified electrician.

Only for frame/facet cooktops:

A small gap will be visible between

cooktop and countertop for the first

days after installation. The gap will

decrease as the cooktop is used. The

electrical safety of your appliance is

warrantied despite the small gap.

IMPORTANT SAFETY INSTRUCTIONS

Use

Do not use the appliance until it has

been properly installed in the

countertop.

Only use the cooktop for residential

cooking, and for the purposes

described in this manual.

Other uses are not permitted and can

be dangerous.

This appliance is equipped with an

overheating protection feature. See

"Overheating protection" for more

information.

Persons who lack physical, sensory

or mental abilities, or experience with

the appliance should not use it without

supervision or instruction by a

responsible person.

Be sure to use the proper type of

cookware. Follow the manufacturer's

instructions.

Never heat up empty pans. This

could damage the appliance and

cookware.

Individuals with a pacemaker or

similar medical device: Please note

that an electromagnetic field develops

when the cooktop is turned on.

If the cooktop is installed above a

pyrolytic oven it should not be used

during the pyrolytic process. The

overheating protection feature of the

cooktop might be activated.

Although unlikely that this will affect a

pacemaker or other medical device,

please consult the device manufacturer

or your doctor if you have concerns.

Keep magnetized items, e.g. credit

cards, disks, etc. away from the

cooktop while in operation. Damage

may result.

IMPORTANT SAFETY INSTRUCTIONS

Injury prevention

Be aware of loose fitting or hanging

clothing when operating the cooktop,

they may present a fire hazard.

Children should not be left

unattended in an area where the

cooktop is in use. Never allow children

to sit or stand on any part of the

cooktop.

Pot and pan handles should be

turned inward and not extend over the

countertop to reduce the risk of burns,

ignition of flammable materials, and

spills.

Caution: Do not store items of interest

to children in cabinets above the

cooktop. Children climbing on the

cooktop to reach these items could be

injured.

Never leave a cooktop unattended

at high settings or when cooking with oil

or fat. Overheated oil could ignite.

Use the Child Safety Lock to prevent Always heat oil slowly, monitoring it as it

children from turning on the burners or

heats.

changing the settings. See "Child

Safety lock" for more information.

Do not use water on grease fires.

Smother or use a dry chemical or

Keep all pots and pans out of

children's reach. Danger of burning or

scalding.

foam-type extinguisher on any fire or

flame.

When frying food make sure that the

food is as dry as possible before

The appliance gets hot when in use

and remains hot for quite a while after

placing it in oil. Moisture can cause hot

being turned off. As long as the surface oil to splatter and boil over. At high

temperature is high enough to cause a

burn, the Residual Heat Indicator will

remain lit. Once sufficient time has

passed and the cooktop surface is safe

to touch, the Residual Heat Indicator

will go out.

settings, be cautious of splattering

grease or boiling over liquids which

may produce smoke.

Do not flambé under an exhaust

hood. Flames could be drawn up into

the hood by the suction and the grease

filters may ignite.

Protect your hands with insulated

gloves or potholders when using the

appliance. Use only dry, heat resistant

potholders. Moist or damp potholders

used on hot surfaces can result in

steam burns. Do not let the potholder

touch the hot heating elements. Do not

use towels or other bulky items near the

appliance.

IMPORTANT SAFETY INSTRUCTIONS

Do not heat unopened containers.

Built-up pressure may cause the

Flammable materials should not be

stored on or near the appliance.

container to burst and result in injury.

The cooktop is fitted with a cooling

Before removing pots and pans be

sure to turn off the burners.

fan. Drawers under the cooktop are not

recommended. If a drawer is fitted

directly underneath the cooktop, ensure

that there is sufficient space between

the drawer, its contents and the

underside of the appliance in order to

ensure sufficient ventilation for the

cooktop. Do not store small items or

To prevent burns and breathing

difficulty, allow the cooktop to cool

before cleaning. Some cleaners may

produce toxic fumes if applied to a hot

surface.

When wiping spills on a hot cooktop paper in the drawer. They could get

sucked into the housing by the fan and

cause damage or impair cooling.

with a wet sponge or cloth, be careful

to avoid steam burns.

Ensure that no aerosols, combustible

liquids or other flammable materials are

kept in this drawer. If cutlery inserts are

to be placed in the drawer they must be

made of heat-resistant material.

Do not let flammable materials,

i.e. cooking grease, accumulate on the

appliance.

Never cover the cooktop with a

cloth. A fire may result.

Do not place items other than pots

and pans on the cooktop.

IMPORTANT SAFETY INSTRUCTIONS

Damage protection

Any spills should be removed as

quickly as possible to prevent them

from burning on and becoming difficult

to remove.

Never place hot pots or pans on the

touch controls, this may damage the

electronics.

Do not use a steam cleaner to clean

Do not drop anything on the ceramic

surface of the cooktop. Even

lightweight objects may cause damage.

this appliance. Steam could penetrate

electrical components and cause a

short circuit.

Do not use pots or pans with

pronounced edges or ridges on the

ceramic cooktop. These could scratch

the cooktop permanently. See

"Cookware" for more information. Grains

of salt and sand can cause scratches.

Make sure that the bases of any pots

and pans are clean, free of any fat or

oils, and are dry.

Do not allow solid or liquid sugar,

pieces of plastic or foil to fall on the

burners when they are hot. If these

residues are allowed to cool on the

ceramic surface pitting or even

cracking may occur.

IMPORTANT SAFETY INSTRUCTIONS

Appliance safety

Further safety notes

In the event of any damage to the

appliance, it must be turned off

immediately and disconnected from the contact with the cooktop. The insulation

Make certain that the power cords of

small appliances do not come in

main power supply. Contact Miele’s

Technical Service Department.

Do not use the appliance until it has

been repaired. Ensure power is not

supplied to the appliance until repair

work is completed.

of the cable could become damaged.

Danger of electric shock!

Keep pets away from the cooktop at

all times and activate the Safety Lock. If

a pet gets on the cooktop a touch

control sensor could be activated

Do not cook on a damaged cooktop. turning on a burner.

Any breakages or cracks in the ceramic

surface of the appliance are defects

and must be treated as such. If the

cooktop should break, cleaning

SAVE THESE INSTRUCTIONS

AND REVIEW THEM

PERIODICALLY

solutions and spills may penetrate the

broken cooktop and create a risk of

electric shock. Do not use the

appliance until it has been repaired.

Repairs should only be performed

by qualified technicians to ensure

safety. Repairs and other work by

unqualified persons could be

dangerous. Do not open the outer

casing of the appliance under any

circumstances.

While the appliance is under

warranty repairs should only be

performed by an authorized service

technician. Otherwise the warranty is

void.

Guide to the cooktop

Cooktop

aBurner with double booster

bcd Burners with single booster

eBurner controls and displays

fTimer controls and display

gChild safety lock indicator

hChild safety lock control

iCooktop On/Off control

jCooktop "On" indicator

Guide to the cooktop

Burner controls and displays

aPower level touch controls

bBurner On/Off touch controls

cBooster indicator

dIndicator for "Auto heat" or extended

power level (see "Programming"),

e.g. front left burner

eDisplays:

= Burner is ready for use

= Burner is turned on

1 to 9 = Power level

= Residual heat

= No pan on burner or pan

unsuitable (see "Induction - How it

works")

= Single booster function

activated

= Double booster function

activated (only front left burner)

= Fault (see "Safety cut-out

feature")

= Auto-heat with extended

power level

P0 etc. = Program (see

"Programming")

S0 etc. = Status (see

"Programming")

Guide to the cooktop

Timer control and display

aTouch control to:

- turn the timer on/off,

- switch between functions, and

- select a burner for "automatic switch-off".

bTouch control for setting the time

cTime display

dAutomatic switch-off indicator

eTimer indicator

Burner data

min to max

diameter *

Rating in watts

208 V**

Burner

240 V**

7" - 11"

normal:

2200

2700

3350

2500

3100

3850

(18 cm - 28 cm) with booster 1:

with booster 2:

4" - 7 " normal:

(10 cm - 16 cm) with booster:

1250

1650

1450

1900

5 ½" - 8" normal:

(14 cm - 20 cm) with booster:

5 ½" - 8" normal:

1700

2250

1950

2600

1700

2250

1950

2600

(14 cm - 20 cm) with booster:

Total:

6700

7700

* Pans with a base diameter within the given range may be used.

** The wattage quoted may vary depending on the size and material of the pans

used.

Induction

How it works

If a suitable pan is placed on the burner

within 3 minutes, the ß will go out and

you can continue cooking as normal.

An induction coil is located under each

burner. When a burner is switched on,

this coil creates a magnetic field which

impacts directly on the base of the pan

and heats it up. The burner itself is

heated indirectly by the heat given off

by the pan.

If no pan or an unsuitable pan is placed

on the burner, the burner and the

cooktop will switch off automatically

after 3 minutes.

Be careful not to place cutlery or

other metal objects on the cooktop.

When the appliance is switched on,

or when there is residual heat

present, there is the risk of metal

objects heating up quickly.

Induction burners only work when a

magnetic based pan is placed on it

(see "Cookware").

Induction automatically recognizes the

size of the pan, i.e. heat is only

generated in the area covered by the

base of the pan.

Beware of burns.

Depending on the material, other

objects left on the cooktop could

also melt or catch fire. Switch the

burners off after use.

The burner will not work:

– if it is switched on without a pan in

place, or if the pan is unsuitable

(non-magnetic base).

– if the diameter of the pan is too small.

– if the pan is taken off the burner

when it is switched on.

If this happens, ß will flash in the

relevant burner display alternating with

0 or the last selected power level

selected.

Induction

Noises

The appliance has a cooling fan to help

extend the life of the electronics. When

the cooktop is being used at high levels

for a long period of time, this will come

on and you will hear a whirring sound.

The fan may continue to run after the

appliance has been switched off.

When using an induction burner, the

following noises can occur in the pan,

depending on what it is made of and

how it is constructed.

– Higher power settings may cause a

buzz. This will decrease or cease

altogether when the power setting is

reduced.

– If the pan base is made of layers of

different materials (e.g. a

sandwiched base), a cracking sound

may be heard.

– Whistling might occur if linked

burners (see "Booster function") are

being used on the highest setting at

the same time, and the pans have

bases made of layers of different

materials.

– You may hear a clicking sound from

the electronic switches, especially on

lower settings.

Induction

Cookware

Pan size

Suitable pans include:

To make optimum use of the burners,

choose cookware that fits between the

inner and outer marking of the burner. If

the base diameter of the pan is smaller

than the inner marking, the induction

heating will not work. The burner will

behave as if it had no pan on it.

– stainless steel pans with a magnetic

base

– enameled steel pans

– cast iron pans

Unsuitable pans:

– stainless steel pans without a

magnetic base

– aluminum and copper pans

– glass, ceramic or earthenware pots

and pans

To test whether a pot or pan is suitable

for use on an induction cooktop, hold a

magnet to the base of the pan. If the

magnet sticks, the pan is suitable.

Unless the pan manufacturer states

that you can do so, do not use pans

with very thin bases on this cooktop.

,^{Never heat up empty pans.}

This could damage the appliance

and cookware.

Before using for the first time

Clean the cooktop

Heat the cooktop

^ Before using for the first time, clean

the appliance with a damp cloth and

dry with a soft cloth.

Metal components of the cooktop have

a protective coating which may give off

a slight odor the first time the appliance

is heated.

The smell will dissipate after a short

time and does not indicate a faulty

connection or appliance defect.

Use

Touch controls

Turning on the cooktop

The control panel on your ceramic

cooktop is equipped with electronic

sensors. They respond to a finger

touch.

To operate the burners, simply touch

the corresponding sensor area(s). Each You will see a dash - in each of the

^ Put a pot or pan on the desired

burner.

^ Touch the ON/OFF "s" cooktop

touch control.

time a command is registered, a signal

will be heard.

burner displays, and the On/Off

indicator will light. If a setting is not

chosen within a few seconds the

cooktop will turn itself off as a safety

measure.

Be sure to touch only the desired

sensor area and keep the control

panel clean and clear. Otherwise,

the touch controls may not respond,

or unintentional commands may be

given, even causing the cooktop to

switch off automatically (see the

section on "Safety cut-out feature").

NEVER place hot cookware on the

sensor areas. The electronics can

be damaged.

Turning on a burner

^ Touch the s On/Off touch control for

the desired burner.

The respective burner display shows 0.

^ Select a power level between 1 and 9

by pressing the + or - control.

When turning on the cooktop you can

decide whether you want to cook with

auto heat or not. See "Auto-heat" for

more information.

Turn on with + to:

cook without auto-heat.

Turn on with – to:

cook with auto-heat.

Use

Settings

Power level*

Use for

standard extended

factory settings settings**

(9 power levels) (17 power levels)

Melting butter

Dissolving gelatine

1 - 2

1 - 2.

3 - 3.

Thickening sauces containing egg yolk and/or butter

Warming small quantities of food/liquid

Cooking rice

Thaw frozen vegetables (blocks)

Warming liquid and half-set foods

Thickening sauces, e.g. Hollandaise

Making oatmeal

Preparing omelettes, lightly fried eggs

Steaming fruit

4 - 4.

Defrosting deep frozen food

Steaming vegetables, fish

Cooking broths, soups

Bringing large quantities of food to a boil

Cooking dumplings

5. - 6

Gentle frying (without overheating the fat) meat, fish,

vegetables, fried eggs

6. - 7.

Frying pancakes, etc.

8 - 8.

Boiling large quantities of water

These settings are intended as guidelines only. With deep pans, larger quantities of food or when

cooking without a lid, a higher setting is required. For smaller quantities, select a lower setting.

** If you wish to fine-tune a setting, you can extend the power level range (see "Programming - P2").

The intermediate setting will be represented by an indicator next to the number.

Use

Auto-heat

When Auto-heat has been activated,

the burner switches on automatically at

the highest setting and then switches to

the continued power level which was

selected. The "heat-up" time depends

on which continued power level has

been chosen (see table).

Continued power

level*

Heat-up time

(approx.)

min : sec

0 : 15

0 : 25

0 : 50

2 : 00

5 : 50

2 : 50

Taking a pan off the zone while

Auto-heat is in operation interrupts the

function. It will resume if a pan is

placed back on the zone within

3 minutes.

The continued cooking settings with a dot

after the number are only available if the

power level range has been extended (see

"Programming - P2").

Use

Activating Auto-heat

At any point during the Auto-heat time

you can use + or - to lower or increase

the continued power level. The

^ Press the - sensor until the desired

continued power level appears,

e.g. 6.

Auto-heat time will adjust accordingly.

In the extended range of settings (see

"Programming - P2"), A flashes

alternately with the continued power

level until the heat-up time has

completed.

During the heat-up time a dot will light

to the right of the continued power

level, and go out when it is completed.

Use

Booster function

The extra boost of energy is only

available by taking a proportion of

Each burner is equipped with a booster

function to temporarily increase the

power level. The front left burner is

equipped with a double booster.

When the booster function is on, the

burners increase to power level 9 for

10 minutes. This boost is intended

quickly bring large quantities of water

to the boil, e.g. when cooking pasta.

A maximum of two booster functions

can be used at one time.

energy away from another burner. For

this reason, the burners are networked

in pairs as shown.

When the booster is activated:

– if Auto-heat is activated or either

burner of the same network, it will

switch off.

If the booster is activated, when

– no power setting is selected, the

burner will revert to power level 9 at

the end of the booster time or when

the booster is switched off.

– the power level on the other linked

burner may decrease.

– if the rear left burner is turned on, it

will switch off if booster 2 for the front

left burner is activated.

– a power setting is selected, the

burner will revert to this pre-selected

power setting at the end of the

booster time or when the booster is

switched off.

Taking a pan off the burner while the

booster is in operation interrupts the

booster function. It will resume if a pan

is placed back on the burner within 3

minutes.

The booster can be switched off by

touching the + and - sensor at the same

time, or by touching the - sensor.

Use

Single booster (all burners)

^ Turn on the relevant burner.

^ Select a power level.

Double booster (front left burner

only)

^ Turn on the relevant burner.

^ Select a power level.

^ Take your finger off the sensor.

^ Touch the + and - sensor briefly at

the same time.

^ Touch the + and - sensor briefly at

the same time.

The indicator for the booster will light

and I will appear in the burner display.

The indicator for the booster will light

and I will appear in the burner display.

If power level 9 was selected, the

booster can be activated by

touching the + sensor only.

^ Touch the + and - sensor briefly at

the same time again.

II will appear in the burner display.

Use

Turning off a burner

Residual heat indicator

^ Touch the s On/Off touch control for The bars of the residual heat indicator

the desired burner.

go out one after another as the burners

cool. The last horizontal line only goes

out when the burner is safe to touch.

The display will show - for a few

seconds. If the burner is still hot the

residual heat indicator will show.

Turning off the cooktop

^ Touch the s On/Off control for the

cooktop.

The residual heat indicator also

reacts to hot dishes and plates

being placed on a burner that is not

switched on.

All burners are turned off. If any burners

are still hot the residual heat indicator

will show in the respective display.

Do not touch any burner or place

any heat sensitive items on a burner

where the residual heat indicator is

lit. Danger of burns, and fire hazard.

,^{Please note that the residual}

heat indicators do not light when

there is a fault message, even if the

burners are hot.

Timer

The cooktop is fitted with a timer which

can be used to time kitchen activities

and/or to switch off the burners

automatically.

Setting the timer

The timer can be used with the cooktop

turned on or off. It works like a manual

kitchen timer.

You can set a time from 1 minute (01) to

9 ½ hours (9.^). If the time is more than

99 minutes (99), the setting will be

shown in half-hour increments, which

appear after the decimal point.

^ Touch the m, - or + sensor.

Two dashes appear in the display, and

the timer indicator will flash.

^ While the indicator is flashing, touch

the - or + sensor until the desired

time appears in the display,

e.g. 15 minutes.

Use the - and + touch controls to raise

and lower the time. There are pre-set

stops at 2 hours and at 99 minutes. To

override a stop, briefly remove your

finger from the touch control, then

touch it again to continue.

The time then counts down in minutes.

The time remaining can be seen in the

display and changed at any time by

touching - or +.

To re-set the display to 00,

simultaneously touch - and +.

When the set time has elapsed, 00 will

appear in the timer display for a few

seconds. At the same time an audible

signal will sound for a few seconds. To

turn the signal off before this, touch the

m sensor.

Timer

Automatic switch-off

^ Touch the - or + sensor until the

desired time appears in the display,

e.g. 15 minutes.

To use this feature, a power setting

must be selected for the desired

burner. All burners can be programmed The time then counts down in minutes.

at the same time.

The time remaining can be seen in the

display and changed at any time by

touching - or +.

If the programmed time is greater

than the maximum operating hours

permitted, the cooktop will

eventually switch-off automatically.

See "Safety cut-out feature" for more

information".

If you want to set another burner to

switch-off automatically, repeat the

same steps.

If more than one switch-off time is

programmed, the shortest time

^ Turn the desired burner on, e.g. rear

right, and select a power level.

remaining will show in the display, the

indicator for that particular burner will

flash. All the other indicators will remain

lit. If you want to check the remaining

time for another zone, touch the m

sensor until the indicator for the desired

burner flashes.

^ Touch the m sensor.

Two dashes appear in the display, and

the timer indicator will flash.

^ Touch the m sensor again.

The indicator for the timer in the display

goes out, and the automatic switch-off

indicator flashes.

^ If several burners are being used,

touch the m sensor repeatedly until

the indicator flashes next to the

burner you wish to use this function

for, e.g. back right.

The indicator for the burners being

used will light up clockwise, starting

with the front left.

Timer

Combi mode

After the last entry, the shortest

remaining time will appear in the

display. If you want to check on another

remaining time, touch the m sensor

until the relevant indicator flashes.

The timer and automatic switch-off

functions can be used at the same

time.

If you have programmed in one or more

switch-off times, and would like to use

the timer as well:

Touch the m sensor repeatedly until

the timer indicator flashes.

Starting with the shortest remaining

time which is shown in the display, all

burners that are in use and the timer

can be selected clockwise.

If you are using the timer, and would

like to program one or more switch-off

times as well:

Touch the m sensor repeatedly until

the indicator flashes for the desired

burner.

Safety features

Child Safety Lock

Manual activation

^ Press and hold the $ Child Safety

Lock control until the respective

indicator lights.

Keep children away from the

cooktop for their own safety.

The cooktop has a Child Safety Lock to

prevent children from turning on the

burners or changing settings.

The indicator will go out after a short

time.

You can alter the setting from one

finger to three finger operation (see

"Programming - P6") to make it harder

for children to operate the appliance.

The Child Safety Lock can be activated

while the cooktop is on or off.

Activating the Child Safety Lock

during cooktop use

– The settings for the burners and

timer cannot be altered.

Automatic activation

The Safety lock will come on 5 minutes

after the cooktop is switched off.

– The burners and cooktop can still be

turned off but once turned off cannot

be turned on again.

To use this feature the setting has be

changed (see "Programming - P7").

Activating the Child Safety Lock

when the cooktop is turned off

– The cooktop cannot be turned on.

Deactivation

^ Press and hold the $ Child Safety

Lock control until the indicator goes

out.

The indicator will come on to show that

the Child Safety Lock has been

activated, if you touch the $ Child

Safety Lock control or try to select a

setting.

In the case of a power failure the

Child Safety Lock will be

deactivated.

Safety features

Stop and Go

To deactivate Stop and Go:

Your appliance has a Stop and Go

feature which, when activated, reduces

the power of all burners that have been

switched on.

^ Press and hold the $ control until the

indicator goes out.

The burners will now run at the level

previously set.

If you then deactivate the feature, the

burners will automatically return to the

previous level.

If the feature is not deactivated, the

cooktop will turn off after 1 hour.

If you wish to use this feature, you will

need to alter the factory setting (see

"Programming - P1").

To activate Stop and Go:

^ Press and hold the sensor $ until you

hear two consecutive beeps.

Be careful not to continue touching

the $ sensor for too long, as this will

activate the safety lock.

The Child Safety Lock indicator will

flash. The power for the activated

burner(s) will reduce to level 1, and 1

will appear in the respective display.

When activating "Stop and Go":

– the countdown of the programmed

time for the automatic switch-off

function will be interrupted. When

deactivating "Stop and Go", the

countdown will continue,

– the timer will continue without

interruption.

Safety features

Safety cut-out feature

Covered touch controls

The cooktop will turn off automatically if

any of the touch controls are covered

for more than 10 seconds, e.g. by

finger contact, food boiling over or by

an object such as an oven mitt or towel.

A tone will also sound every 30 secs.

for a maximum of 10 min and an F will

flash in the display of the sensor which

is covered.

The cooktop is on too long

The cooktop has a safety cut-out

feature in case it is not turned off after

use.

If one of the burners is heated for an

unusually long period of time (see

table), and the power level settings are

not adjusted, the cooktop will turn itself

off automatically and the residual heat

indicator will light.

Power level*

Maximum

operating hours

^ Clean the touch controls or remove

the object covering it.

1 / 1.

2/ 2.

3 /3.

4 / 4.

5 / 5.

6 / 6.

7 / 7.

8 / 8.

This will turn off the signal tone and the

displayed F will go out.

^ Turn the cooktop on again with the s

touch control. The burners can now

be used.

The power settings with a dot after the number

are only available if the power setting range has

been extended (see "Programming - P2.").

^ To use the burners again, turn the

cooktop back on in the usual way.

Safety features

Overheating protection

Overheating can be caused by:

– heating an empty pan.

The induction coils and the cooling

element of the electronic are fitted with

a overheating protection feature. This

prevents the induction coils and cooling

element from overheating.

– fats or oils being heated on the

highest power setting.

– there being insufficient ventilation to

the under side of the appliance.

This mechanism works on the affected

burner or on the entire cooktop in the

following ways:

If the overheating protection

mechanism triggers again, contact

Miele Technical Service.

– If the booster function is being used,

this will be switched off.

– The power level will be reduced.

– If an induction coil is affected, the

cooktop will switch off. The fault

code FE99 will be displayed.

The burner can be used again as soon

as it has cooled to a safe temperature.

– If the cooling element is affected, the

power supply to the burners will be

reduced, and the set power level will

continue to be displayed.

As soon as the cooling element has

cooled sufficiently, the burners will

automatically continue to operate at the

original power setting.

Cleaning and Care

Do not use a steam cleaner to clean

this appliance. Steam could

penetrate electrical components and

cause a short circuit. Pressurized

steam could cause permanent

damage to the surface and to

components.

Clean any spills immediately before

they become difficult to remove.

Clean the appliance regularly,

preferably after each use. Allow the

appliance to cool before cleaning.

^ Wipe off any soiling using a damp

cloth. Stubborn soiling is best

removed with a shielded scraper

blade.

Do not use any sharp pointed

objects which could damage the

seal between the ceramic surface,

the surrounding frame and the

countertop.

^ Apply a ceramic cleaner using a soft

cloth or paper towel. To remove any

limescale deposits or metallic residue

apply a ceramic cleaner using a soft

cloth and a shielded scraper blade if

necessary.

Never use abrasive or caustic (oven)

cleaners, dishwasher detergent,

scouring pads, steel wool or hard

brushes. They will damage the

surface.

^ After cleaning wipe the ceramic

surface with a damp cloth and dry.

The ceramic surface can be cleaned

using a cleaner for ceramic

surfaces. Follow the manufacturer’s

instructions.

A cleaner with a special additive to

prevent water marks and smears on the

ceramic surface may be used.

Any melted solids like sugar, plastic or

aluminum foil should be removed as

soon as possible, while the burner is

still warm. If they are allowed to harden

the cooktop may become pitted.

Make sure that no cleaner residue

remains on the ceramic surface by

carefully wiping the cooktop with a

damp cloth. They may damage the

cooktop or produce toxic fumes

when heated.

^ Turn the burner off.

^ Using a shielded scraper blade,

scrape the melted item immediately

off the burner while it is still hot.

Use caution: Danger of burns!

Be sure that pot and pan bases are

clean and dry.

After cleaning, dry the ceramic

surface with a soft cloth to prevent a

build up of limescale deposits.

^ Allow the cooktop to cool and clean

as previously described.

Programming

The cooktop's default settings can be

adjusted (see table).

Saving the settings

^ Press and hold the On/Off "s" touch

control until the displays go out.

^ While the cooktop is turned off, touch

the On/Off "s" control and Child

Safety Lock "$" control at the same

time until the Child Safety Lock

indicator flashes.

Not saving the settings

^ Press and hold the Child Safety Lock

"$" control until the displays go out.

The burner display shows P (Program)

and S (Status) with a number. The

number indicates the current setting.

To set the desired program:

^ Touch the + or – control of the front

left burner to select the program

desired.

To set the status (see table):

^ Touch the + or – control of the front

right burner to select the desired

status.

Several programs can be adjusted one

after another by repeating the steps

listed above.

Programming

Programming Table

Program*

Status** Setting

Demonstration mode and

factory default settings

Demonstration mode on

Demonstration mode off

Restore Factory default settings

Stop and Go

Off

Power level range

9 power levels

(1 to 9)

17 power levels

(1, 1., 2, 2., 3 ... to 9)

If the Auto heat setting is

selected, an A will flash

alternately with the continued

power level in the display

Warning tone when there

is no pan or the pan is

unsuitable

Off

Quiet

Medium

Loud

Keypad tone when a

control is touched

Off

Quiet

Medium

Loud

Timer tone volume

Off

Quiet - 10 seconds

Medium- 10 seconds

Loud - 10 seconds

* Programs / status not shown are not allocated.

** The factory default setting is printed in bold.

Programming

Program*

Status** Setting

Safety lock manual activation

procedure

One finger lock using $

Three finger lock using $

and + on the two right-hand

burners

Safety lock activation

Manual activation

Automatic activation 5

minutes after cooktop is

turned off

Auto heat

Off

6. Sensor reaction time

Low

Normal (300 ms)

Fast

* Programs / status not shown are not allocated.

** The factory default setting is printed in bold.

Frequently asked questions

Repairs should only be carried out by an authorized technician in accordance

with local and national safety regulations. Unauthorized repairs could cause

injury or appliance damage.

What if the cooktop or the burners cannot be turned on?

Possible fault

The cookware is not suitable for an Use the correct pots and pans, see

induction cooktop. "Cookware".

Solution

The Child Safety Lock is activated. Deactivate the safety lock.

See "Child Safety Lock".

The main fuse has blown.

Check the main fuse.

What if the burner does not heat up but can be turned on and a power level

can be selected?

Possible fault

Solution

The cooktop is in the demo mode. See "Programming - P0".

What if a ß appears in a burner display?

Possible fault

The burner was turned on without Be sure the correct burner is turned on and

a pan on it. a pan is on it.

The cookware is not suitable for an Use the correct pots and pans, see

induction cooktop. "Cookware".

Solution

What if a single burner or the whole cooktop switches itself off?

The Safety cut-out or Overheating protection feature has been activated. See

"Safety features".

What if food does not cook when using auto-heat?

Possible fault

Solution

The pot or pan does not transfer

heat properly.

Use the correct pots and pans, see

"Cookware".

Large amounts of food are being

cooked.

Select a higher continued power level.

Frequently asked questions

What if one of the following has occurred?

Possible fault

Solution

The booster has automatically switched

off early.

The overheating protecting feature has

been triggered, see "Safety features".

The power level has dropped.

The burner is not working as usual.

What if the cooling fan continues to run after the appliance has been

switched off?

This is not a fault. The fan will continue running until the appliance has cooled. It

will then switch itself off automatically.

What if an F appears in the display for the rear burners, an E appears in the

display for the front burners and numbers appear in the timer display

Possible fault

Solution

FE99

The overheating protection mechanism

has triggered. The burner can be used

again as soon as it has cooled down to

a safe level.

Other fault messages

Interrupt the power supply to the

cooktop for approx. 1 minute.

If the problem persists after

reconnecting the appliance to the

power supply, please contact the Miele

Technical Service department.

Technical Service

In the event of a fault which you cannot MieleCare

easily fix yourself, please contact the

(USA only)

Miele Technical Service Department

using the information on the back of this MieleCare, our Extended Service

manual.

Contract program; gives you the

assurance of knowing that your

appliance investment is covered by 5

years of worry free ownership.

MieleCare is the only Extended Service

Contract in the industry that guarantees

repairs by a Miele Authorized Service

Provider using genuine Miele parts.

Only genuine Miele parts installed by

factory trained professionals can

guarantee the safety, reliability and

longevity of your Miele appliance.

When contacting Technical Service

quote the serial number and model of

the cooktop. This information is visible

on the silver data plate.

Please note that unless expressly

approved in writing by the Miele

Service department, Extended Service

Contracts offered by other providers for

Miele products will not be recognized

by Miele. Our goal is to prevent

unauthorized (and untrained) service

personnel from working on your Miele

products, possibly doing further

damage to them, you and/or your

home.

To learn more about MieleCare

Extended Service Contracts, please

contact your appliance dealer or visit

us online at:

http://miele.com/mielecare

Installation Instructions

To prevent accidents

and machine damage

read these instructions

before

installation or use.

IMPORTANT SAFETY INSTRUCTIONS

Note to the installer:

Please leave this instruction book

with the consumer for the local

electrical inspector’s use.

2 ”

The minimum distances given in

these Installation Instructions must

be observed in order to ensure safe

operation. Failure to do so increases

the risk of fire.

recommended

The cabinetry and venting hood

should be installed first to prevent

damage to the cooktop.

The cooktop should only be installed

as shown in the illustrations while

maintaining the required safety

distances shown. Do not install the

cooktop between two tall cabinets, this

is a fire hazard.

2 ”

50mm

a A minimum distance of 2"

(50 mm) from the cooktop to the rear

wall and a side wall or cabinet must

be maintained for safety.

not recommended

The countertop must be bonded

with heat resistant (212 °F/100 °C)

adhesive to prevent distortion or

dissolving.

The cooktop must not be installed

over a dishwasher, washer, dryer,

refrigerator or freezer. Heat radiated by

the cooktop may damage them.

not allowed

The cooktop must only be installed

above an oven if it has a built-in cooling

fan.

IMPORTANT SAFETY INSTRUCTIONS

To eliminate the risk of burns or fire

by reaching over heated surfaces

Safety distances above the

appliance

cabinet storage space above the

cooktop should be avoided. If cabinet

storage is necessary, the risk can be

reduced by installing a venting hood to

project horizontally a minimum of 5"

(127 mm) beyond the bottom of the

cabinets.

Because of the heat radiated it is not

recommended to install the cooktop

above a drawer. It should be installed

above a cabinet base unit with a

dummy drawer front. A protective base

should also be installed between the

dummy drawer and the cooktop. There

must be a minimum distance of 4 ½"

(110 mm) between the top of the

The minimum safety distance given by

the hood manufacturer must be

maintained between the cooktop and

the hood above it. See the installation

instructions of the hood for these safety

measurements.

countertop and the top of the protective

base to ensure proper ventilation.

This appliance has not been

If the hood manufacturers instructions

are not available or if flammable objects

are installed over the cooktop (e.g.

cabinets, utensil rail, etc.), a minimum

safety distance of 30" (760 mm) must

be maintained.

designed for maritime use or for use in

mobile installations such as recreational

vehicles or aircraft. However, under

certain conditions it may be possible for

installation in these applications. Please

contact the Miele Technical Service

Department with specific requirements.

If there is more than one appliance

beneath a hood (e.g. wok burner

and electric cooktop), and they have

different minimum safety distances

always observe the greater

distance.

The cooktop must not be

permanently sealed into the countertop

when installed. The sealing strip under

the edge of the cooktop provides a

sufficient seal for the countertop.

Once installed, be sure that the

power cord cannot come into contact

with the underside of the cooktop or

any mechanical parts.

Installation

Cooktops flush with the countertop

Frame/Facet cooktops

aWall

bWall covering

cBack splash

dCountertop

eCountertop cut-out

f2" (50 mm) minimum distance

Installation

Installation dimensions

2^9/16"

1/4"

5/16"

(514mm)

(8mm)

1/4"

(65mm)

(794mm)

_ß3/16"

R4mm)

max

9/16"

(

_{( 5}⁰₀2_m"_m)

max

40mm)

(

19 _11/16"

11/16"

)

(500₊mm)

1/16"

(780

(76mm)

2^9/16"

(65mm)

1/2"

(317mm)

9/16

(65mm)

aFront of cooktop

bInstallation height

cInstallation height power supply

dPower cord encased by flexible metal conduit

Length = 3' 11" (1200 mm) C = ³/₄" (19 mm)

Installation

Ventilation

27^9/16"

(700mm)

(75mm)

aFront of cooktop

bCut-out at the rear wall of the cabinet for ventilation

cProtective base

If a protective base is fitted, there must be a distance of at least 4 ½" (110 mm)

between the top of the protective base and the top of the countertop, for proper

ventilation of the appliance. At the back there has to be a gap of 3" (75 mm) for

the power cord.

Installation

Cut out

Installing the cooktop

^ Make the countertop cut-out following ^ Feed the cooktop connection cable

the dimensions given in the

illustration.

down through the cut-out.

^ Place the cooktop centrally in the

cut-out. When doing so make sure

that the seal under the cooktop sits

flush with the countertop on all sides.

This is important to ensure an

Remember to maintain a minimum

distance of 2" (50 mm) between the

rear wall and the right or left side.