GM ONSTAR CLASS II DATA BUS INTERFACE
GMOS-04
INSTALLATION INSTRUCTIONS
* READ IMPORTANT WARNING ON PAGE 1
BEFORE ATTEMPTING ANY INSTALLATION
THE GMOS-04 IS DESIGNED TO BE USED WITH VEHI-
CLES THAT HAVE A FACTORY AMPLIFIED SYSTEM
INCLUDING THE BOSE AUDIO SYSTEMS. BESIDES
RETAINING THE ONSTAR SYSTEM, THE GMOS-04 WILL
ALSO RETAIN THE WARNING CHIMES THAT WILL BE
LOST WHEN THE FACTORY RADIO IS REMOVED. THE
GMOS-04 WILL ALSO PROVIDE A 12 VOLT SWITCHED
WIRE FOR PROPER RADIO OPERATION. THE GMOS-04
NOW PROVIDES MUTE, PARKING BRAKE, VSS OR
SPEED SENSE, AND A REVERSE OUTPUT TO MAKE
INSTALLING AN AFTERMARKET NAVIGATIONAL RADIO
SIMPLER AND LESS TIME CONSUMING.
• SEE APPLICATIONS LIST INSIDE •
TOOLS REQUIRED FOR INSTALLATION
• Cutting Tool • Tape • Crimping Tool
• Connectors (ie: butt-connectors, bell caps, etc.)
REV. 03/19//07
INSTGMOS-04
1-800-221-0932
©Copyright 2004-2007 Metra Electronics Corporation
GMOS-04
4. Connect the Green/Purple wire to the reverse wire of the aftermarket radio.
APPLICATIONS
IMPORTANT
GMC
BUICK
• When completed, plug the 14 pin harness into the GMOS-04.
• THE BROWN LOOP ON THE 16 PIN HARNESS MUST BE CUT THEN TAPED UP.
PLEASE REFER TO THE ONSTAR LEVEL AJUSTMENT SECTION FOR FURTHER
DETAILS ABOUT THE BROWN WIRE.
ENVOY 2002-07
SAVANA 2003-07
SIERRA 2003-06
YUKON/XL/DENALI 2003-06
HUMMER
ALLURE 2005-07
CENTURY 2004-05
RAINIER 2004-07
RENDEZVOUS 2002-07
TERRAZA 2005-07
CADILLAC
INSTALLING THE GMOS-04
1. With all connections completed to the aftermarket radio, plug the 24 pin and
CONNECTIONS TO BE MADE ON THE
24 PIN GRAY HARNESS:
1. Connect the yellow wire to the radio’s 12V battery or memory wire.
2. Connect the red wire to the radio’s ignition or accessory wire.
3. Connect the black wire to the radio’s ground wire.
the 12 pin connectors into the vehicles corresponding wiring harnesses.
2. Reconnect the negative battery terminal.
H2 2003-07
3. Cycle the key by turning the ignition on then back off, then back on again
H3 2006-07
ESCALADE 2003-06
ESCALADE EXT 2003-06
CHEVROLET
to test the radio.
ISUZU
ASCENDER 2003-07
OLDSMOBILE
ALERO 2001-04
BRAVADA 2002-05
INTRIGUE 2002
SILOUETTE 2000-04
PONTIAC
TESTING THE GMOS-04
1. Turn the ignition on then the radio to verify the radio works. Check balance
and fader controls for proper operation. If controls are backwards, check to
see if the RCA’s are in the correct location.
AVALANCHE 2003-06
CAVALIER 2000-05
IMPALA 2000-05
4. Connect the orange wire to the radio’s illumination wire. If the wire is not
present, tape up wire.
MALIBU 2002-03
MALIBU CLASSIC 2004
MONTE CARLO 2000-05
SILVERADO 2003-06
SILVERADO CLASSIC 2007
SSR 2003-06
5. Connect the orange/white wire to the radio’s dimmer wire. If the wire is not
present, tape up wire.
2. Push the Onstar button to verify Onstar is working. the radio will shut off and
Onstar will be heard through the left front speaker. Turn off Onstar and the
radio will turn back on.
• When completed, plug the 16 pin harness into the GMOS-04.
AZTEC 2001-05
GRAND AM 2001-05
GRAND PRIX 2004-06
SUNFIRE 2000-05
SAAB
CONNECTIONS TO BE MADE ON THE
14 PIN HARNESS
ONSTAR LEVEL ADJUSTMENT
SUBURBAN 2003-06
TAHOE 2003-06
To adjust the Onstar volume level find the BROWN wire that you cut on the 16 pin
harness, you will use the BROWN wire that is by itself, with no other wire with it.
Push the blue Onstar button, while the voice is speaking tap the BROWN wire to
ground. There are 4 volume settings for Onstar; once the 4th setting is reached
and the BROWN wire is tapped to ground it will automatically go back to the first
volume setting. Once the volume is set it will stay at that volume until the BROWN
wire is tapped to ground again. This can be set during installation and then left
alone. If user adjustment is desired, a momentary contact switch (sold separately)
can be added. Connect one terminal from the switch to ground and the other ter-
minal to the brown wire. The volume will change one level every time the switch
is pressed.
9-7x 2005-07
TRAILBLAZER 2002-07
VENTURE 2000-05
1. Connect the blue/white wire to the radio’s AMP turn-on wire.
2. Connect the red wire to the radio’s Igniton or accessory wire.
3. Connect the RCA cables to the radio’s RCA outputs. If no RCA outputs are
available, use the Metra line output converter part #ALO-648 (SOLD SEPARATELY).
4. The white RCA goes to the left front RCA output of the radio.
5. The gray RCA goes to the front right RCA output of the radio.
6. The green RCA goes to the left rear RCA output of the radio.
7. The purple RCA goes to the right rear RCA output of the radio.
INTERFACE COMPONENTS
• GMOS-04 Data Interface
• 14 pin harness with RCA’S
• 16 pin harness to 24 pin GM harness and 12 pin Onstar harness
The following wires on the 14 pin harness are for the aftermarket radios that
have navigation built in:
WIRING UP THE GMOS-04
* Important: Before beginning any of the following, disconnect the negative
1. Connect the Brown wire to the mute wire of the aftermarket radio..
battery terminal to prevent accidental short circuit.
2. Connect the Green wire to the parking brake wire of the aftermarket radio..
**Note: The ignition power source of most GM vehicles keep the radio on until
one of the doors is opened. This is called the R.A.P. (retained accessory power).
The GMOS-04 is designed to retain this feature.
3. Connect the Blue/Pink wire to the VSS or speed sense wire of the aftermarket
radio.
2
3
4
GMOS-04
TOUBLESHOOTING:
Chime Too Loud/Soft:
There are some instances where the chime is too loud or too soft.
To resolve this follow these steps:
1. Make sure the ignition is turned to the “off” position.
2. Disconnect the 14 pin and 16 pin wire harnesses from the GMOS-04
3. Open up the GMOS-04 by squeezing the sides of the top cover
4. Locate the potentiometer facing up on the circuit board, this is the
Chime potentiometer
5. Taking a small flat headed screwdriver, turn the potentiometer clockwise
to decrease the chime level; turning the potentiometer counterclockwise
will increase the chime level
6. After adjustment replace top cover of GMOS-04 and reconnect
wire harnesses
Distorted Audio Output:
When using the GMOS-04 with a radio that has a high pre-out voltage,
usually greater than 2 volts, the audio signal may become distorted.
To resolve this follow these steps:
1. Make sure the ignition is turned to the “off” position
2. Disconnect the 14 pin and 16 pin wire harnesses from the GMOS-04
3. Open up the GMOS-04 by squeezing the sides of the top cover
4. Locate the potentiometer next to the 10 pin board mounted connector
located at the end of the GMOS-04
5. Taking a small flat headed screwdriver, turn the potentiometer counter-
clockwise to lower the input level going to the factory amplifier
6. After adjustment replace top cover of GMOS-04 and reconnect wire
harnesses.
5
|