C O N T E M P O R A R Y
C o r d l e s s
3 6 0 °
J u g
SABS
IEC60355
M o d e l :
21405/6
2200W
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
ADDITIONAL WARNINGS FOR KETTLES:
Note:
1.
The kettle and base must not be operated with any
other models of kettle.
•
If the kettle is switched on when empty or with
insufficient water, then the kettle will switch off
automatically to protect against dry boiling. Wait
until the heating element cools down, refill with tap
water and use as normal. This protection function
is not designed for regular use, as it will shorten the
life of the kettle.
If the kettle is overfilled, boiling water may be
ejected.
The kettle is only to be used with the stand
provided.
The appliance must not be immersed during
cleaning.
If the supply cord is damaged, the manufacturer or
its service agent or a similarly qualified person must
replace it in order to avoid a hazard.
2.
The kettle is fitted with a dry-operation cutout
that switches off the kettle if it has boiled dry. If
this happens allow the kettle to cool down for
approximately 15 minutes, then fill the kettle with
cold water. This will reset the cutout so that the
kettle can be used again.
•
•
•
•
3.
4.
5.
Do not overfill. Check the inside water level gauge
when filling.
Never remove the cord from the kettle while in
operation. Switch off the appliance first.
Ensure the lid is closed properly before switching
on, to prevent water splashing out when boiling. Do
not open the lid when boiling.
After the kettle has boiled it may need a few minutes
to cool down before restarting.
Take care when pouring. Pour slowly and do not
over-tilt.
Make sure the kettle is always used on a flat
surface.
Water will remain hot for considerable time after
boiling and will present a scalding hazard. Take
care and keep away from children.
6.
7.
8.
9.
Descaling
Always ensure that the kettle is disconnected from the
mains before descaling. Scaling or furring is a common
problem in hard water areas. It is recommended that
a propriety descaler is used whenever scale deposits
build up. The instructions supplied with the descaler
must always be followed. Scale build up may result in the
kettle switching off before boiling. Using a water purifier
will help to reduce scale build-up.
10. The outside surface of the kettle will become hot
during use. To avoid injuries only hold the handle.
11. Take care to avoid contact with the steam coming
from the lid or spout.
Ensure that you descale your filter at regular intervals to
avoid impairing the pouring performance of your kettle.
INSTRUCTIONS FOR USE:
It is important that you read these instructions before
using your kettle for the first time.
Cleaning and Maintenance
A clean appliance will last longer. Please observe the
following instructions to get the best use of your kettle.
1.
Open the lid of the kettle, fill with tap water to the
desired level. (min. capacity is 0.5L and max.
capacity is 1.7L). In hard water areas, using
purified or filtered water is recommended to reduce
the amount of scale build up in the kettle.
Close the lid by pressing it down until it clicks into
place. Place the kettle on the base and plug into
the mains.
To switch on the kettle, press the On/Off switch
down (position 1). The power indicator light will
now be on. When the water has boiled the kettle
will automatically switch off. You can stop the kettle
at any time by pressing the On/Off switch down
(position 0).
•
•
Always disconnect the plug from the mains before
cleaning the kettle and base. Wipe the plastic
parts and base with a moist cloth. Never use an
aggressive scourer, steel wool of strong chemical
cleaners.
Descale the kettle regularly. This will depend on the
hardness of the water and the frequency of use.
Scale build up will significantly reduce the heating
efficiency of the kettle.
2.
3.
•
•
Use of a proprietary descaler for kettles is
recommended. Follow the instructions provided
carefully.
For stainless steel kettles you should use a soft
absorbent cloth to remove the condensation from
the body to prevent minerals in the steam/water
from oxidizing and giving the appearance of rust
marks on the kettle. A metal polish should be
used to protect and maintain your kettle in a good
condition.
4.
Pour slowly and carefully. If you wish to re-boil,
please allow a few moments for the kettle to cool
down and reset. WARNING!
If the kettle has just boiled it will be full of steam that
will escape if the lid is opened resulting in a burn
hazard.
CAUTION!
Kettle parts are hot and can cause injury. Hold the
handle only.
Disposal and the Environment
IMPORTANT!
If your electrical appliance requires replacement or
is of no further use, please think of protecting the
environment. Contact you local authority for advice as
many have facilities for environmentally safe disposal.
Do not open the lid when steam is coming out of the
spout. When pouring or filling always remember to
disconnect from electricity.
Trouble Shooting Guide
Problem
Reason
Action
Pre-caution
Kettle is leaking water
May be condensation
This is normal if boiled a num-
ber of times in succession
Pour out water to MAX level.
This kettle is for household
use only.
Kettle is over filled
If overfilled water can eject
from the kettle resulting in a
hazard
Switch is sticking
Ensure switch button is clean.
Switch on household socket
Keep appliance away from
cooking splatter.
Kettle does not work
Household socket is off.
Ensure water covers the ele-
ment before operating.
Appliance must be of similar
wattage to prevent overloading.
Your life of the kettle will be
reduced if not seated on base
correctly.
Household socket is not
working
Check the socket with another
appliance
Kettle is not seated on base
correctly.
Seat kettle on base correctly
Kettle trips mains power
supply
Overloaded circuit.
Unplug all appliances attached
to the same circuit.
Note that their can be up to 5
household plug sockets on 1
circuit.
Kettle takes too long to boil
Kettle works intermittently
Kettle is rusting on outside
Element has lime scale
deposits.
Descale element using a
proprietary descaler or citric
acid solution. If not successful
then a new element may be
required.
Kettles with scale will have a
reduced lifespan. Clean the
scale regularly.
Element has lime scale
deposits.
Descale element using a
proprietary descaler or citric
acid solution. If not successful
then a new element may be
required.
Kettles with scale will have a
reduced lifespan. Clean the
scale regularly.
Steam deposit has oxidised and
turned into an orange colour.
Wipe your kettle after each use
to keep dry. Polish stainless
steel occasionally.
Keeping any appliance clean
at all time will extend the life of
the product.
Element is rusting. Rust spots
on element.
Water deposits on the element.
Some areas have water that
will result in orange or brown
stains.
Some stains are stubborn and
a descaler may not be effective.
This should not affect function.
Use distilled water.
Kettle does not switch off
automatically
Lid not positioned correctly
or is off.
Place lid on the kettle securely.
Ejecting steam from the spout
or lid can be a hazard
Service Centre Share Call: 086 111 5006
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a
|