Side by Side Refrigerator
USER’S GUIDE
Congratulations on your purchase
™
of a Maytag Performa refrigerator! Your
satisfaction is very important to us, so please
read this guide carefully. You will find instructions
on the proper operation and maintenance of your
new appliance.
Table of Contents
Save time and money. If something should go wrong,
we suggest consulting the “Before You Call” section
of this book. It is designed to help you solve basic
problems before consulting a servicer.
Safety Instructions. . . . . . . . . . . . . . . . . 1
Installation . . . . . . . . . . . . . . . . . . . . . . . 2
Temperature Controls . . . . . . . . . . . . . . 3
Looking Inside . . . . . . . . . . . . . . . . . . 4-5
Ice Service . . . . . . . . . . . . . . . . . . . . . 6-7
Food Storage Tips . . . . . . . . . . . . . . . . . 8
If you have questions, write us (include your model
number and phone number) or call:
Maytag Appliances Sales Company
SM
Attn: CAIR Center
P.O. Box 2370
Cleveland, TN 37320-2370
1-800-688-9900 USA
1-800-688-2002 CANADA
Storing the Refrigerator,
Care & Cleaning. . . . . . . . . . . . . . . . . . . 9
1-800-688-2080 USA TTY (for deaf, hearing
impaired or speech impaired)
(Mon.–Fri., 8am–8pm Eastern Time)
Cleaning Chart. . . . . . . . . . . . . . . . . . . 10
Before You Call. . . . . . . . . . . . . . . . . . . 11
Warranty. . . . . . . . . . . . . . . . . . . . . . . . 12
Guide de L’Utilisateur . . . . . . . . . . . . . 13
Guia del Usuario . . . . . . . . . . . . . . . . . 26
Form No. A/12/99
Part No. 111107-1
MCS Part No. 61004966
Litho U.S.A.
Installation
Your new refrigerator was packed carefully for shipment. Remove and discard shelf packing clips (if used) located just above
each shelf where they hook onto the frame. To remove plastic clips wiggle the clips sideways and pull straight out.
Location
• Allow for a free flow of air through the front base
Leveling
To enhance appearance and to maintain optimal perfor-
mance, the refrigerator must be level. Your refrigerator
has wheels which can be adjusted for leveling:
grille.
• Install the refrigerator where the room temperature
will not go below 55˚ F. With temperatures below 55˚,
the refrigerator will not run frequently enough to
maintain proper temperature in the freezer.
• Remove the lower hinge covers (see fig. 1). To do this,
grasp each cover near the hinge and apply pressure.
The attachment tabs will snap out, allowing removal
of the covers.
• Allow a minimum 1/2” clearance on the sides, top
and back for ease of installation. If refrigerator is
placed with either door hinge side against a wall,
you may want to allow additional space so the door
can be opened wider.
• Adjust the wheels with a screwdriver (see fig. 2).
• To lock the cabinet in place, turn down both level-
ing/lock feet, located near the front wheels (see fig.
3). Rear leveling/lock feet are not required.
• Use caution when installing the unit on vinyl or
hardwood floors so as not to mark or otherwise
damage the flooring. A piece of plywood, a rug or
other material should be used to protect the floor
while positioning the unit.
• Replace the hinge covers.
• If the floor is not level and it is necessary to raise the
rear of the cabinet, we suggest rolling the rear wheels
onto a piece of plywood or other shim material.
Fig. 1
TURN CLOCKWISE TO
RAISE CABINET CORNER
TURN
COUNTER-CLOCKWISE
TO LOWER CABINET
CORNER
Fig. 2
Fig. 3
2
Temperature Controls
Your refrigerator has two temperature controls. These controls are located at the top rear of the fresh food com-
partment.
5
5
FREEZER
FRESH FOOD
4
6
9
4
6
7
8
7
8
3
2
3
2
INITIAL SETTING IS 5
COLDEST IS 9
OFF IS 0
9
1
1
ALLOW 24 HOURS
0
BETWEEN ADJUSTMENTS
To adjust the controls, rotate the knobs to the desired settings.
Step 1
Step 2
Initial Temperature Control
Settings
Adjusting the Temperature
Controls
• 24 hours after adding food, you may decide that one
or both compartments should be colder or warmer. If
so, adjust the control(s) as indicated in the table
below.
• The fresh food control has settings from 1 (warmest)
to 9 (coldest). Initially set this control on 5.
• The freezer control has settings from 1 (warmest) to
9 (coldest). Initially set this control on 5.
• Except when starting the refrigerator, do not change
either control more than one number at a time.
• It is recommended that the coldest freezer setting (9)
be used for short periods only.
• Allow 24 hours for temperatures to stabilize before
resetting.
• Let the refrigerator run at least 8-12 hours before
adding food.
• Changing either control will have some effect on the
temperature of the other compartment.
Your refrigerator will run continuously for several
hours when you first start it. This is normal
Temperature Control Guide
Turn fresh food control to next higher setting.
Turn fresh food control to next lower setting.
Turn freezer control to next higher setting.
Turn freezer control to next lower setting.
Set fresh food control to 0 (Off).
Fresh Food Compartment too Warm
Fresh Food Compartment too Cold
Freezer too Warm
Freezer too Cold
Turn Refrigerator Off
NOTE: Turning the fresh food control to 0 stops cooling in BOTH compartments. It does not shut off power to
the refrigerator.
No Defrosting
Warm Cabinet Surfaces
At times, the front of the refrigerator cabinet may be
warm to the touch. This is a normal occurrence that
helps prevent moisture from condensing on the cabi-
net. The condition will be more noticeable when you
first start the refrigerator, during hot weather and after
excessive or lengthy door openings.
Your refrigerator is designed to defrost automatically.
NOTE: During the automatic defrost cycle, you may
notice a red glow/reflection in the vents on the back
wall of the freezer compartment and you may hear the
sound of water droplets coming into contact with the
defrost heater. This is normal during the defrost cycle.
3
Looking Inside
Shelves
The Tempered Glass Cantilever Shelves in your refrig-
erator are adjustable, allowing you to customize the
interior to meet your food storage needs.
To remove a shelf:
• unload
• slightly lift up the rear of the shelf
• pull the shelf straight out
To lock the shelf into another position:
• tilt up the front edge of the shelf
• insert the hooks into the desired frame openings
• let the shelf settle into place
WARNING — Never attempt to adjust a shelf that is loaded with food.
The freezer basket or drawer (style will vary by model)
The Freezer Shelves rest on support rails molded into
the wall of the freezer. Select models offer freezer
shelves that slide forward for easier access to items at
the rear of the shelf.
slides out for more convenient access to the frozen
foods. The basket or drawer rests and slides on support
rails molded into the wall of the freezer.
To remove a freezer basket:
To remove the shelf:
Slide out until it stops. Lift the front edge and continue
sliding forward until out. To replace, line the basket or
drawer up with the support rails, lift the front edge
slightly, and slide it into place.
Completely unload the shelf and lift straight up. Tilt
the shelf sideways and pull it straight out. To replace,
reverse the above procedure.
Storage Drawers
The Crisper provides ideal storage for fruit and veg-
etables. There is a humidity control located on the
crisper shelf above the crisper drawer.
To remove the crisper drawer for cleaning:
• pull out the crisper until it stops
• tilt the drawer front up and pull it out
When storing fruit, slide the crisper control to the left
(LOW) to provide lower humidity conditions in the
drawer.
To replace the crisper drawer:
• align the drawer in the tracks
• lift the drawer front and slide in
When storing vegetables, slide the crisper control to
the right (HIGH) to provide higher humidity condi-
tions in the drawer.
For best results, keep the crisper tightly
closed.
The Crisper Shelf Top serves as the lower refrigerator shelf.
To replace the crisper shelf:
To remove the crisper shelf:
• set the rear bars on the support
• lift the front edge of the shelf
• pull the shelf straight out
• push the shelf back until the front edge can be low-
ered into place
4
Looking Inside
The VariTemp Drawer (select models) is designed to
provide a short term storage area for fresh meats,
cheeses and luncheon meats.
The Removable Door Bins, (select models) are
designed to accommodate gallon-plus sized contain-
ers. They are adjustable and easily removed.
To remove: Lift the bin up until it clears the retainers
on the door liner, then pull the bin straight out. Reverse
the above procedure to replace the bin.
The temperature control for this drawer is located on
the left side wall of the refrigerator, near the front of the
drawer. The “cool” setting maintains a temperature
within the drawer consistent with the surrounding
fresh food compartment. To achieve a lower tempera-
ture within the drawer, slide the control towards the
“cold” setting. A lower temperature within the drawer
is recommended when storing fresh meat, poultry or
fish.
Package Dividers, (select models) fit in refrigerator
and freezer door shelves to secure bottles and other
containers in place when the door is opened or closed.
Package Dividers are adjusted by sliding side to side.
Cold
Cool
The Dairy Compartment (select models), located in the
refrigerator door, features extra deep storage for butter
and cheeses. Some models are equipped with a butter
dish, which is found in this compartment.
The Egg Tray (style may vary) holds a “dozen-plus”
eggs. It can be removed to be washed or carried to a
work area.
Energy Saving Tips
• Locate the refrigerator away from heat producing
appliances such as the range or dishwasher, heat
vents and direct sunlight.
• Keep the freezer full to near capacity so less cold air
will escape during door openings. When the freezer
is less than two-thirds full, place milk cartons half
full of water in the freezer.
• Level the refrigerator and do not block ventilation
around the front grille.
• Wipe moisture from the outside of containers before
placing them into the refrigerator.
• Let hot dishes cool slightly before putting into the
refrigerator or freezer.
• Avoid opening the doors too often.
• Cover liquids.
5
Ice Service
Automatic Ice Maker
The water inlet tubing assembly required to complete the
water connection to the water valve is located in a bag
inside the refrigerator. Connect the ice maker to the
water supply as instructed in the separate instructions
furnished with the refrigerator.
To remove the ice bin:
• Pull down on lower back edge of the Automatic
Dispenser bin front and pull it straight out. To
replace the bin, align its bottom rails to the corre-
sponding shelf grooves and push it straight back
until it stops and latches. Make sure the tabs, at the
back of the bin, that turn the spiral auger are posi-
tioned between the prongs from the auger motor. To
avoid the ice maker dumping ice while the bin is
removed, turn the ice maker off by lifting the wire
lever.
• Turn the ice maker on by lowering the wire lever arm.
• Beverages and foods should not be placed in the ice
storage bin for quick chilling. These items can block the
wire lever arm, causing the ice maker to malfunction.
• Turn off (arm up) the ice maker when the water
supply is to be shut off for several hours.
For Your Safety
Do not place fingers or hands on the automatic ice
making mechanism while the refrigerator is plugged
in. This will help protect you from possible injury. It
will also prevent interference with moving parts of the
ejector mechanism and the heating element that
releases the cubes.
• After your refrigerator has been hooked up to the
water supply, move the wire lever arm into the down
position. This will start its operation. The ice maker
will fill with water when the freezer reaches the
proper temperature.
• It may be 8 to 12 hours before the ice maker furnishes
any usable ice cubes. The first one or two batches will
probably contain undersized and irregular cubes
because of air in the supply line.
Under certain rare circumstances, ice cubes may be dis-
colored, usually appearing with a green-bluish hue.
The cause of this unusual discoloration can be a com-
bination of factors such as certain characteristics of
local waters, household plumbing and the accumula-
tion of copper salts in an inactive water supply line
which feeds the ice maker.
• The initial batch may also contain impurities from the
new water supply piping. Therefore, all cubes from
the first two or three batches should be discarded.
Continued consumption of such discolored ice cubes
may be injurious to health. If such discoloration is
observed, discard the ice cubes and contact your dealer
to purchase and install a water line filter.
• When the ice cubes are ejected it is normal for several
cubes to be joined together at the ends. They can
easily be broken apart. The ice maker will continue to
make ice until the supply of ice cubes raises the wire
lever arm, shutting the ice maker off.
• Certain sounds may accompany the various cycles of
the ice maker. The motor may have a slight hum, the
cubes will rattle as they fall into an empty storage pan
and the water valve may click or “buzz” occasionally.
• If the ice is not used frequently, the ice cubes will become
cloudy, shrink, stick together and taste stale. Empty the
ice storage bin periodically and wash it in lukewarm
water. Be sure to dry the bin before replacing it.
6
Ice and Water Service
Dispenser Light
Automatic Ice and Water Dispenser
Your dispenser may have a light switch located on the
right side of the dispenser. Depress the switch to turn
the light on or off.
DISPENSER
CONTROL
PANEL
CUBE CRUSH WATER
REFRESHMENT CENTER
LIGHT LOCK
Lock Switch
ACTUATOR
PAD
Your dispenser may be furnished with a lock switch on
the right side of the dispenser. This push button switch
will turn your ice and water dispensers on or off.
SPILL
TRAY
Spill Tray
Do not pour water into the Spill Tray grille at the
bottom of the dispenser area. This is a spill area, NOT a
drain. Normal, small spills will evaporate. Larger spills
should be wiped up with a soft cloth or sponge. The
grille slides out for clean up. Replace the grille by slid-
ing it into the track and pressing on the locking tabs. It
is recommended to clean the spill area occasionally to
prevent mineral deposits.
Dispensing Water and Ice
To dispense ice or water, position a glass against the top
portion of the actuator pad and press. Hold the glass
high in the dispenser opening to avoid spills.
To stop dispensing, release the pressure on the actuator
pad and hold the container in position momentarily to
catch the last pieces of ice or the last drops of water. The
ice delivery door will remain open for a short time.
When it closes, a closing sound can be heard.
Ice Dispensing Tips
• Some crushed ice may be dispensed even though
cubed ice was selected. This happens occasionally
when a few cubes are accidentally channeled into the
crusher.
To select ice cubes, crushed ice or chilled water, slide
the control to the appropriate setting.
• Likewise, when changing from crushed ice to cubes,
some crushed ice may be dispensed. This may also
happen if irregular sized cubes or ice chips are in the
storage bin.
• If the ice dispenser is not used frequently, ice cubes
may clump together and may need to be broken
apart or discarded.
CUBE CRUSH WATER
• A slight pause may be noticed when dispensing
crushed ice. This is normal because the ice is being
channeled to the crusher. Crushed ice pieces will
vary in size and shape.
Water from the dispenser is not as cold as ice water. For
colder water, simply add ice before dispensing the
water. The first glass or two of water dispensed each
time may be warmer than subsequent glasses. A full
glass of water will be cooler than a partial glass. To pre-
vent splashing, fill the glass with ice before adding
water.
• Do not add ice to the storage bin which was not pro-
duced by your ice maker, it may not crush and/or
dispense properly.
• Avoid operating the ice dispenser continuously for
more than five minutes. Remove large quantities
from the bin by hand.
NOTE: When using the ice dispenser for the first time,
discard the first two or three dozen cubes. When using
the water dispenser for the first time, press the actuator
pad for one to two minutes to bleed the air from the
water line. Discard the first five to six glasses of water
dispensed. This will insure pure and fresh water for
drinking.
• Avoid dispensing ice directly into fine china or deli-
cate crystal. The pressure of pressing against the
actuator pad and the ice dropping into the container
can cause cracking or chipping of delicate items.
7
Food Storage Tips
Fresh Food Storage
Frozen Food Storage
• The fresh food compartment of a refrigerator should
be kept between 34°F and 40°F with an optimum
temperature of 37°F. To check the temperature, place
an appliance thermometer in a glass of water and
place in the center of the refrigerator. Check after 24
hours. If the temperature is above 40°F adjust the
controls as explained on page 3.
• The freezer compartment of a refrigerator should be
kept at 0°F or lower. To check the temperature, place
an appliance thermometer between the frozen pack-
ages and check after 24 hours. If the temperature is
above 0˚F, adjust the control as described on page 3.
• A freezer operates more efficiently when it is at least
two-thirds full.
• Avoid overcrowding the refrigerator shelves. This
reduces the circulation of air around the food and
results in uneven cooling.
Packaging Foods for Freezing
• To minimize dehydration and quality deterioration
use aluminum foil, freezer wrap, freezer bags or air-
tight containers. Force as much air out of the pack-
ages as possible and be sure they are tightly sealed.
Trapped air can cause the food to dry out, change
color and develop an off-flavor (freezer burn).
Fruits and Vegetables
• Storage in the crisper drawer traps moisture to help
preserve the fruit and vegetable quality for longer
time periods. (Refer to page 4).
• Sort fruits and vegetables before storage and use
bruised or soft items first. Discard those showing
signs of decay.
• Overwrap fresh meats and poultry with suitable
freezer wrap prior to freezing.
• Do not refreeze meat that has completely thawed.
• Always wrap odorous foods such as onions and cab-
bage so the odor does not transfer to other foods.
Loading the Freezer
• Avoid adding too much warm food to the freezer at
one time. This overloads the freezer, slows the rate of
freezing and can raise the temperature of frozen
foods.
• While vegetables need a certain amount of moisture
to remain fresh, too much moisture can shorten stor-
age times (especially lettuce). Drain vegetables well
before storing.
• Leave a space between the packages so cold air can
circulate freely, allowing food to freeze as quickly as
possible.
Meat and Cheese
• Raw meat and poultry should be wrapped securely
so leakage and contamination of other foods or sur-
faces does not occur.
• Avoid storing hard-to-freeze foods such as ice cream
and orange juice on the freezer door shelves. These
foods are best stored in the freezer interior where the
temperature varies less with door openings.
• Occasionally mold will develop on the surface of
hard cheeses (Swiss, Cheddar, Parmesan). Cut off at
least an inch around and below the moldy area. Keep
your knife or instrument out of the mold itself. The
remaining cheese will be safe and flavorful to eat. Do
NOT try to save individual cheese slices, soft cheese,
cottage cheese, cream, sour cream or yogurt when
mold appears.
Dairy Food
• Most dairy foods such as milk, yogurt, sour cream
and cottage cheese have freshness dates on their car-
tons for appropriate length of storage. Store these
foods in the original carton and refrigerate immedi-
ately after purchasing and after each use.
8
Storing the Refrigerator
d) clean and dry the refrigerator thoroughly,
Vacations
If you will be gone for a month or less, leave the con-
trols at the usual settings.
e) leave the doors open to prevent odors.
During longer absences:
a) remove all food,
Moving
When moving, follow steps a–d under Vacations. In
addition, remove and carefully pack any items that are
easily removable. Ship the refrigerator in an upright
position with the doors taped shut.
b) shut off the ice maker (if installed) and the valve
where you tapped into the water line to supply the
refrigerator,
c) disconnect the refrigerator from the electrical
outlet,
Care and Cleaning
™
Refer to the chart on the following page for specific
refrigerator cleaning guidelines.
No Clean Commercial-duty
Condenser
Disconnect the power cord before cleaning.
A clean condenser means more efficient refrigerator
operation. Thanks to the unique design of the No
Clean condenser, there is no longer a need for routine
condenser cleaning in normal home usage surround-
ings.
™
Cleaning Under the Refrigerator
Your refrigerator can be rolled out for cleaning the floor
underneath. Raise the locking feet if engaged (see page
2). Pull the refrigerator straight out from the wall.
Some operating environments may be particularly
dusty or greasy. In these situations, the condenser can
be periodically cleaned to insure maximum efficiency.
Replacing a Light Bulb
CAUTION: Disconnect the power cord before replacing light bulb(s). Wear gloves as protection
against possible broken glass.
Always use a standard 40 or 60 watt appliance bulb.
Refrigerator
Freezer (Select Models)
To replace a light bulb at the upper rear, unscrew the
bulb located in the center opening on the bottom of the
control cover. The replacement bulb can then be
screwed in. If more access is required for bulb replace-
ment, grasp the control cover in the two lower rear
“finger tabs”, pull down slightly to clear retainer tabs
and slide the cover forward until it is free. After replac-
ing the bulb, align the control cover on to the ribs and
slide it straight back until it snaps onto the retainer
tabs.
(1) unhook the tabs on the top of the light shield by
pressing in with the thumb on the center top of the
light shield; (2) pivot the shield down; (3) unscrew the
bulb when cool and replace with a standard 40 watt
appliance bulb; (4) pivot the shield up into place, snap-
ping the tabs into the slots.
Dispenser Light (Dispenser Models Only)
For replacement, use a 120V, 7 watt bulb. Disconnect
the power cord before replacing the light bulb.
9
Care and Cleaning
CAUTION: Disconnect the power cord before cleaning. Do not touch refrigerated surfaces with
wet or damp hands. Damp objects stick to cold metal surfaces. Before cleaning the freezer, allow it to
warm up. Allow glass shelves to warm up before immersing in warm water.
Refrigerator Cleaning Chart
Refrigerator Exterior
Part
Cleaning Agents
Tips and Precautions
Soap and water
Mild liquid sprays
Vacuum cleaner
attachment
Base grille
No need for cleaning unless environment is particu-
larly greasy, dusty or there is significant pet traffic in
the home (see page 9).
Cleaning brush (Part
No. 20001017).
Available from
your dealer.
Condenser
Soap and water
Mild liquid sprays
Door handles
Dry with a clean, soft cloth.
Soap and water
Mild liquid sprays
Painted metal
surfaces:
Cabinet, doors
Do not wipe the refrigerator with a soiled dishwash-
ing cloth or wet towel. These may leave residue that
can scratch and weaken the paint. Do not use scour-
ing pads, powdered cleansers, bleach or cleaners con-
taining bleach. These products can scratch and erode
the paint finish.
Do not wax plastic or vinyl parts.
Refrigerator & Freezer Interior
Baking soda and
water
Soap and water
Use 1-2 tablespoons baking soda per quart of water.
Be sure to wring out excess water from sponge or
cloth when cleaning around controls, lights, or elec-
trical parts.
Door gasket
Soap and water
Glass cleaner
Mild liquid sprays
Allow the glass to warm up to room temperature
before immersing in warm water. Never use hot
water.
Glass shelves
Soap and water
Baking soda and
water
See above for baking soda solution.
DO NOT use abrasive cleaners, concentrated deter-
gents, bleaches, cleaning waxes, solvents or polish
cleaners to clean the refrigerator interior.
Interior and door
liner
Drawers, bins, egg
cradle, etc.
Soap and water
Dry thoroughly. Do Not wash in automatic diswasher.
10
Before You Call
Check these points if your refrigerator...
• temperature control turned to “Off”
• power cord not plugged in
Won’t Run
• no power at the electrical outlet
• circuit breaker tripped or the house fuse blown
• refrigerator is in automatic defrost
• today’s refrigerators are larger and run colder, which requires more running time to
provide more stable temperatures
• prolonged door openings
Runs too long/too frequently
• base grille blocked
• too many door openings
• door not sealing (due to a package or a container holding door open)
• cabinet not level
• weak floor
Noisy operation
Odor in cabinet
• odor producing foods should be covered or wrapped
• interior needs cleaning
• normal air flow for condenser circulation
Warm air from cabinet bottom
Cabinet Vibrates
• cabinet not level
• weak floor
• hot, humid weather
• frequent or prolonged door openings
• door not closed properly
Moisture on inside cabinet walls
• food not wrapped properly
• hot, humid weather
Excessive moisture in crisper
Cabinet light not working
• bulb burned out
• no power at the outlet
• a normal sound caused by defrost water dripping on defrost mechanism
• appearance of a red glow or reflection is normal during the defrost cycle
Sizzling sound in freezer
Visible glow in the freezer vents
• products with high sugar content may not harden completely when frozen (ice
cream, concentrated juice, etc.)
Freezer not freezing properly
Ice cubes evaporate
• adjust freezer control to a colder setting
• cold air moving over the ice cubes causes shrinkage, especially with limited usage.
This is normal.
• stop arm in OFF (up) position
• water supply turned off
• water pressure too low
• freezer too warm
Automatic ice maker not operating
Front cabinet surface
warm to the touch
• special design to limit condensation during periods of high humidity
• ice jam in the dispenser
• ice maker not operating
• lock switch on
Ice dispenser not operating
• water supply turned off
• water pressure too low
• lock switch on (see pg. 7)
Water dispenser not operating
For further assistance contact Maytag Appliances Sales Company, Maytag Customer Assistance:
U.S. 1-800-688-9900 or Canada 1-800-688-2002
11
Refrigerator Warranty
Full One Year Warranty
For one (1) year from the date of original retail purchase, any part that fails in normal home use will be repaired or replaced
free of charge.
Ice Maker – when purchased with the refrigerator and installed by the dealer the ice maker will be considered part of the
refrigerator for warranty purposes.
Limited Warranty — Major Refrigeration Components
Second thru Fifth Year:
After the first year from the date of original retail purchase, through the end of the fifth year, Maytag Appliances will
repair or replace, at its option, free of charge for parts and labor, any part of the sealed refrigeration system (consisting
of the compressor, evaporator, condenser, drier and connecting tubing) and the cabinet liner (exclusive of the door liner)
which fail in normal home use. Mileage and transportation charges, if required, shall be the responsibility of the owner.
Please note: The full warranty and the limited warranties apply when the refrigerator is located in the United States or
Canada. Refrigerators located elsewhere are covered by the limited warranties only including parts that fail during the first
year.
LIMITATIONS OF LIABILITY
The warrantor shall not be liable for any incidental or consequential damages, including food loss. Some states do not allow the
exclusion or limitation of consequential damages, so the above limitation or exclusion may not apply to you.
The specific warranties expressed above are the ONLY warranties provided by the manufacturer. This warranty gives you
specific legal rights, and you may also have other rights that vary from state to state.
To Receive Warranty Service
To locate an authorized service company in your area contact the Maytag dealer from whom your appliance was purchased; or call
Maytag Appliances Sales Company, Maytag Customer Assistance at the number listed below. Should you not receive satisfactory war-
ranty service, please call or write:
Maytag Appliances Sales Company
SM
Attn: CAIR Center
P.O. Box 2370
Cleveland, TN 37320–2370
U.S.
1-800-688-9900
CANADA 1-800-688-2002
U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.
NOTE: When writing about an unsolved service problem, please include the following information:
(a) Your name, address and telephone number;
(b) Model number, serial number, and revision number (found on the top front interior of the refrigerator compartment);
(c) Name and address of your dealer and the date the appliance was bought;
(d) A clear description of the problem you are having;
(e) Proof of purchase (sales receipt).
What Is Not Covered By These Warranties:
1. Conditions and damages resulting from any of the
following:
5. The cost of service or service call to:
a. Correct installation errors.
a. Improper installation, delivery, or maintenance.
b. Any repair, modification, alteration or adjustment not
authorized by the manufacturer or an authorized ser-
vicer.
c. Misuse, abuse, accidents, or unreasonable use.
d. Incorrect electric current, voltage or supply.
e. Improper setting of any control.
b. Instruct the user on proper use of the product.
c. Transport the appliance to the servicer.
6. Consequential or incidental damages sustained by
any person as a result of any breach of these war-
ranties.
Some states do not allow the exclusion or limitation of
consequential or incidental damages, so the above exclu-
sion may not apply.
2. Warranties are void if the original serial numbers have been
removed, altered, or cannot be readily determined.
3. Light bulbs.
4. Products purchased for commercial or industrial use.
User’s Guides, service manuals and parts catalogs are available from Maytag Appliances Sales Company, Maytag Customer Assistance.
12
th
MAYTAG • 403 W. 4 Street N. • P.O. Box 39 • Newton, Iowa 50208
Form No. A/12/99
Part No. 111107-1
MCS Part No. 61004966
Litho U.S.A.
|