9900CD Manual 1/20/03 12:19 PM Page 1
R
Installation
and Operations
Manual
M9900CD
AM / FM / WB and CD Stereo Receiver
9900CD Manual 1/20/03 12:19 PM Page 3
Location and Function of Controls at a Glance (Continued)
8. Recall Button #5: Press when programming a radio station into memory #5 (CH5). Press when recall-
ing memorized radio station #5. Press to play the CD that follows the one that is currently playing in the
optional CD changer.
9. Weather Band Radio Button: At any time when the unit is on, press this button to access the weather
band radio.
10. Logic Reset Button: If the display or front panel functions become locked and inoperative, press this
button to return all logic back to “Default Mode”. Note: All clock and station recall memory will be lost.
11. Display Button: Press this button at any time, when the unit is on, to display the clock indefinitely.
If you tune to another radio station the radio frequency will be displayed for 5 seconds then will
switch back to the clock. Pressing the "Display" button a second time will display the radio fre-
quency indefinitely. This procedure operates the same for CD mode.
12. Radio Band Select Button: Press this button to select FM1, FM2, FM3, AM1 or AM2 radio bands.
13. Source Mode Button: Press this button to change the play source. If a CD is loaded, and the radio is
playing, you can press the “MODE” button to switch between each source.
14. CD Eject Button: Press this button to eject a CD.
15. CD Slot: To play a CD, insert CD into slot with label facing up.
16. Radio Station/ Clock Display Area: This area displays the radio station, last pushed station recall but-
ton and the clock.
17. CD Function Display Area: This area of the display shows all CD and function indicators.
3
9900CD Manual 1/20/03 12:19 PM Page 4
Listening to the Radio
1. Push the “POWER” button (1) once to turn the unit on.
2. Press the “BAND” button (12) to select a radio
band: FM1, FM2, FM3, AM1 or AM2.
3. To manually tune in a radio station, rotate the
“Tuning” knob (3) right or left until the desired
station is located.
4. To “Automatic Scan” to the next strong station.
Press and release the “Tuning” knob (3). The
tuner will scan up and wait for 5 seconds then
scan up again. Once the desired station is found,
press the knob again to stop the scan function.
5. To “Seek” up or down to the next station, momen-
tarily rotate the “Tuning” knob (3) right or left
and hold it for more than one second then
release it.
Sound Controls
Volume Button:
Press the “VOLUME” button (2) to select between
the sound controls Volume, Bass, Treble, Balance
and Fader (Figures A-E).
Figure A
Bass Control:
The bass control adjusts the amount of low
frequency that you hear.
Figure B
Figure C
Figure D
Figure E
Treble Control:
The treble control adjusts the amount of high
frequency that you hear.
Balance Control:
The balance control adjusts the amount of sound
output to the left and right speakers.
Fader Control:
The fader control adjusts the amount of sound
output to the front and rear speakers.
Programming the Unit
You can program up to 15 FM radio stations and 10 AM radio stations.
1. Select FM1, FM2, FM3, AM1 or AM2 by pressing the “BAND” button (12) repeatedly while watching the
indication on the display (16).
2. Use the “Tuning” or “Scan” (3) knob to select the desired station.
3. Press and hold one of the five station recall buttons (4-8). The button number and “CH” appears in the
display area (16). Release the button.
4. Repeat the procedure to memorize more stations as desired.
4
9900CD Manual 1/20/03 12:19 PM Page 5
Weather Band Radio Operation
1. Press the “W.BAND” button (9) to activate the
weather band radio. (The weather band radio will
then take priority over the AM/FM Radio or CD).
The weather band radio will search for the
strongest radio signal in your area.
2. To scan all 7 weather band stations, press the
“Scan” button (3)
3. Press the “W.BAND” button once again to turn off
the weather band radio.
CD Operation
1. Insert a compact disc into the CD disc slot
(15). The disc will auto load and auto play (The
disc icon in the display will begin to rotate). If
the disc does not auto load, do not force it.
Press the “Eject” button (14) as you may
already have a disc inserted.
2. To change the music track, rotate the “Track”
knob (3) to the right or left (Figure A). Track
change indication will appear in the display
area (17).
Figure A
3. To preview each song on the disc for 10 sec-
onds, press the “INTRO” button (6). “INT” will
appear in the display area. To turn off this fea-
ture, press the “INTRO” button again. The indi-
cator in the display will disappear (Figure B).
Figure B
5
9900CD Manual 1/20/03 12:19 PM Page 6
CD Operation (Continued)
4A. To repeat play of a single song on the CD, press
the “REPEAT” button (5) one time. The “RPT”
indicator will appear in the display area (Figure C).
4B. Press the “REPEAT” button again to stop the
repeat function. The indicator in the display (17)
will disappear.
5. To “Pause” the playing of the disc, press the
“PLAY/PAUSE” button (4) once. To resume play,
press the “PLAY/PAUSE” button again (Figure D).
Figure C
6. To eject the disc, press the “Eject” button (14).
If the CD is not removed after three seconds it
will be reloaded into the unit.
Figure D
CD Changer Control (Optional)
1. Load your CD changer with compact discs per
the manufacturer’s operating instructions.
2. Press the “MODE” (13) button until the display
reads “CDC” which indicates that the CD chang-
er is active (Figure A).
3. To change the active CD, press either the “DISC
DOWN” (7) or “DISC UP” (8) buttons to scroll
through your selection of CD’s in the CD chang-
er. If a CD is not in a tray in the changer, the
M9900CD will continue to scroll through the
trays until one is found.
Figure A
6
9900CD Manual 1/20/03 12:19 PM Page 7
Auxiliary Input
1. Press the “MODE” (13) button until the display
reads “AUX” which indicates that the auxiliary
unit is playing through the M9900CD (Figure A).
2. All tonal features (Volume, Bass, Treble, Balance
and Fader) are active when the auxiliary source
is playing.
Figure A
Specialty Features
Reset Button:
If by chance the function of the front panel becomes
“Locked-Up” (front panel buttons don’t function at
all) or the display area become unreadable, use a
ballpoint pen to press the “Reset” button (10).
Pressing the reset button clears all memory and
resets the display to it’s DEFAULT settings. All recall
buttons will lose their programming and the clock
will lose the set time. All these functions will have to
be reprogrammed.
☛
Mode Button:
The “MODE” button (13) is used to select between
the sound sources: Radio, CD, CD Changer or
Auxiliary Source (Figures A-D).
Figure A
Figure B
Figure C
Figure D
Example:
I
f a CD has been inserted, repeated pressing of the
“Mode” button will change the sound output from
one source to another. The source that is playing will
be indicated in the display area.
7
9900CD Manual 1/20/03 12:19 PM Page 8
Specialty Features (Continued)
Display Button:
When the unit is on, press the “Display” (11) but-
ton at any time to display the clock indefinitely. If
you tune to another radio station, the frequency
will be displayed for 5 seconds, then will switch
back to the clock. Pressing the “Display” button
a second time will display the radio frequency
indefinitely. This procedure operates the same in
CD mode.
Setting the Clock:
To set the clock, press the “Power” button (1) to turn
the unit on and perform the following procedure:
1. Press and hold the “DISPLAY” button (11) until
the display begins to flash.
2. Use the “Clock Setting” knob (3) to adjust the
hours (When selecting hours note the AM or PM
indicator) and minutes as indicated on the con-
trol. Rotate the knob left to adjust minutes and
rotate right to adjust hours.
Hours
Minutes
8
9900CD Manual 1/20/03 12:19 PM Page 9
Installation Procedure
White Wire: Connect this wire to the Left Front
Speaker (+) positive terminal or wire.
S
tep 1: The radio chassis is designed to be “Sleeve
Mounted” through a opening in the dashboard panel.
The required opening size is 182mm (7-3/16") x
84mm (3-5/16"). Cut or engage an opening in the
dashboard to accommodate the mounting sleeve.
White Wire with Black Stripe: Connect this wire to the
Left Front Speaker (-) negative terminal or wire.
Green Wire with Black Stripe: Connect this wire to the
Left Rear Speaker (-) negative terminal or wire.
Step 2: If you are replacing an existing factory
installed radio, an adapter harness might be avail-
able for your vehicle to eliminate the need for cut-
ting your factory wiring. Contact Radio Shack or
other car stereo installation centers for the availabil-
ity of a harness for your vehicle.
Green Wire: Connect this wire to the Left Rear
Speaker (+) positive terminal or wire.
Gray Wire: Connect this wire to the Right Front
Speaker (+) positive terminal or wire.
Step 3: Insert the mounting sleeve into the hole in
the dashboard. Bend the metal tabs on the sleeve to
secure the mounting sleeve to the dashboard.
Gray Wire with Black Stripe: Connect this wire to the
Right Front Speaker (-) negative terminal or wire.
Step 4: Bring all wiring for the connection of the unit
(including the antenna) through the center of the
mounting sleeve. Connect the wiring as follows:
Purple Wire with Black Stripe: Connect this wire to
the Right Rear Speaker (-) negative terminal or wire.
Purple Wire: Connect this wire to the Right Rear
Yellow Wire (w/Fuse): Connect this wire to a con-
stant +12 volt power source (a power source that is
not controlled by the ignition key).
Speaker (+) positive terminal or wire.
Note: This unit is designed to connect to (4) four
speakers. If the installation only requires (2) two
speakers, use the White and Gray wire sets to con-
Orange Wire: Connect this wire to the factory (+)
dashboard lighting circuit that is controlled by the nect the speakers.
headlight switch or dashboard light illumination
control switch (dimmer control). If no dashboard
lighting circuit is available, connect this wire to the
BLUE wire provided on this harness. Note: If this
wire is not connected, the panel lighting on this unit
will not illuminate.
WARNING!
Any wires left unconnected must be taped-off or
capped off to prevent shorting.
DO NOT connect speaker ground wires together.
Red Wire: Connect this wire to a switched +12 volt
power source (a power source turned on and off by
the ignition key).
DO NOT connect speaker ground wires to the chas-
sis of the vehicle.
Blue Wire: Connect this wire to the (+) power
antenna activation circuit. If no power antenna
exists, tape-off the end of this wire to prevent short-
ing out of the unit.
DO NOT connect front and rear speaker wires
together.
FAILURE TO FOLLOW ANY OF THESE WARNINGS
WILL RESULT IN DAMAGE TO THIS UNIT AND
VOIDS THE WARRANTY.
Note: This wire can also be used to activate the
panel lighting on this unit if no dashboard lighting
circuit is available (see information for orange wire
connection).
Black Wire: Connect this wire to the frame of the
vehicle (ground). This wire is the chassis grounding
wire for the unit.
9
9900CD Manual 1/20/03 12:19 PM Page 10
Installation
Sheet
Metal
Screw
Nut
Washer
Metal Strap
Dashboard
Mounting Sleeve
Speaker Connection
Right
Right
Front Speaker
Rear Speaker
-
+
+
-
Purple Wire: Rear Right Speaker (+)
13
12
11
10
9
Purple/Black Wire: Rear Right Speaker (-)
Gray/Black Wire: Front Right Speaker (-)
Gray Wire: Front Right Speaker (+)
Green Wire: Rear Left Speaker (+)
Green/Black Wire: Rear Left Speaker (-)
White/Black Wire: Front Left Speaker (-)
8
7
White Wire: Front Left Speaker (+)
6
Black Wire: Ground
5
Blue Wire: Power Antenna
Red Wire: Switched
4
3
Orange Wire: Dimmer
Yellow Wire: 12 VDC Constant
2
-
+
1
+
-
15A
Left
Front Speaker
Left
Rear Speaker
10
9900CD Manual 1/20/03 12:19 PM Page 11
Auxiliary Connection
VCR
OR
TV
M9900CD
RED (RIGHT)
WHITE (LEFT)
OR
VIDEO GAME
AUDIO OUT FROM
VCR / TV / VIDEO GAME
CD Changer Connection
CD CHANGER
M9900CD
MALE/MALE
(supplied with CD changer)
BLACK
11
9900CD Manual 1/20/03 12:19 PM Page 12
Warranty
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within one year from the date of sale to
you, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found
defective in materials or workmanship, when properly connected and operating on the cor-
rect power requirements designated for the specific product. This warranty and Magnadyne
Corporation or its authorized agents obligations hereunder do not apply where the product
was; damaged while in the possession of the consumer, subjected to unreasonable or unin-
tended use, not reasonably maintained, utilized in commercial or industrial operations, or
serviced by anyone other than Magnadyne Corporation or its authorized agents, or where the
warning seal on the product is broken or the power and/or plugs are detached from the unit.
Magnadyne Corporation or any of its authorized agents will not assume any labor costs for
the removal and reinstallation of any product found to be defective, or the cost of trans-
portation to Magnadyne Corporation or its authorized agents. Such cost are the sole respon-
sibility of the purchaser.
This warranty does not cover the cabinet appearance items or accessories used in connec-
tion with this product, or any damage to recording or recording tape, or any damage to the
products resulting from improper installation, alteration, accident, misuse, abuse or acts of
nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND
ONE YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may have other rights that vary from state to state.
Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220.
Return Authorization must be obtained before sending, or merchandise may be refused.
© Copyright 2003
M9900CDM Rev. A 01-17-2003
Magnadyne Corporation
12
|