CellPipe™ 20 Series
User’s Guide
Part Number: 7820-0766-004
November, 2001
Customer Service
Customer Service
Product and service information, and software upgrades, are available 24 hours a day.
Technical assistance options accommodate varying levels of urgency.
Finding information and software
To obtain software upgrades, release notes, and addenda for these products, log in to
Lucent OnLine Customer Support also provides technical information, product
information, and descriptions of available services. The center is open 24 hours a day,
seven days a week. Log in and select a service.
Obtaining technical assistance
Lucent OnLine Customer Support at http://www.lucent.com/support
provides easy access to technical support. You can obtain technical assistance through
email or the Internet, or by telephone. If you need assistance, make sure that you have
the following information available:
•
•
•
•
•
Active service or maintenance contract number, entitlement ID, or site ID
Product name, model, and serial number
Software version or release number
Software and hardware options
If supplied by your carrier, service profile identifiers (SPIDs) associated with
your line
•
Your local telephone company’s switch type and operating mode, such as AT&T
5ESS Custom or Northern Telecom National ISDN-1
•
•
•
Whether you are routing or bridging with your Lucent product
Type of computer you are using
Description of the problem
CellPipe™ 20 Series User’s Guide
iii
Customer Service
Obtaining assistance through email or the Internet
If your services agreement allows, you can communicate directly with a technical
engineer through Email Technical Support or a Live Chat. Select one of these sites
Calling the technical assistance center (TAC)
If you cannot find an answer through the tools and information of Lucent OnLine
Customer Support or if you have a very urgent need, contact TAC. Access Lucent
ContactUsfor a list of telephone numbers inside and outside the United States.
Alternatively, call 1-866-LUCENT8 (1-866-582-3688) from any location in North
America for a menu of Lucent services. Or call +1 510-769-6001 for an operator. If
you do not have an active services agreement or contract, you will be charged for
time and materials.
iv
CellPipe™ 20 Series User’s Guide
Contents
Customer Service ..................................................................................................... iii
About this guide .................................................................................................... 1-1
What is the CellPipe 20 Series Product Family? ................................................... 1-2
Lucent TURN-UP .................................................................................................. 1-3
CellPipe 20 Series management ............................................................................ 1-3
Setup ..................................................................................... 2-1
Verifying package contents ................................................................................... 2-1
Items you need for installation .............................................................................. 2-2
Connecting CellPipe 20 Series products ............................................................... 2-2
Checking status lights ............................................................................................ 2-4
Console setup ......................................................................................................... 2-4
Syntax of command-line interface ......................................................................... 3-1
Using the commands ............................................................................................. 3-2
Viewing the main menu ................................................................................. 3-2
Displaying information about a command ..................................................... 3-2
Returning to the main menu ........................................................................... 3-3
Displaying second-level commands ............................................................... 3-3
Saving configurations ..................................................................................... 3-3
Bridging commands ............................................................................................... 3-3
Routing commands ................................................................................................ 3-6
CellPipe™ 20 Series User’s Guide
v
Contents
Auto-provisioning .................................................................................................. 4-1
Configuring WAN interface .................................................................................. 4-2
Configuring LAN interface .................................................................................... 4-7
Configuring the manage command ........................................................................ 4-9
Configuring the mode command ........................................................................... 4-9
Configuring the quick command ......................................................................... 4-10
Configuring the r1483 command ......................................................................... 4-11
Configuring the dnsrelay command ..................................................................... 4-13
Configuring the ipoa command ........................................................................... 4-13
Configuring the pppoa command ........................................................................ 4-14
Configuring the pat command ............................................................................. 4-15
Preparing to upgrade .............................................................................................. 5-1
Obtaining software ................................................................................................. 5-1
Upgrading software ............................................................................................... 5-2
Warranties and FCC Regulations ...................................... A-1
Product warranty ................................................................................................... A-1
Warranty repair .............................................................................................. A-2
Out-of warranty repair ................................................................................... A-2
FCC Part 15 Notice ............................................................................................... A-2
IC CS-03 Notice ................................................................................................... A-3
vi
CellPipe™ 20 Series User’s Guide
Introduction
About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
What is the CellPipe 20 Series Product Family? . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Lucent TURN-UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
CellPipe 20 Series management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
About this guide
This document is a combined user’s guide for the CellPipe™ 20 Series Product
Family. The products currently addressed by this guide include the following:
•
•
CellPipe 20A-GX, supporting software version 1.65LU
CellPipe 20S, supporting software version 1.51LU
The contents of this guide include basic information about the aforementioned units,
such as standard features, setup instructions, and information on how to configure and
administer the units. This guide is written primarily to provide information for
network administrators responsible for configuring and administering the units and
secondarily to acquaint users with the functionalities of the units.
For additional support, you can also visit the Lucent OnLine Customer Support at
most current release notes for this product family.
CellPipe™ 20 Series User’s Guide
1-1
Introduction
What is the CellPipe 20 Series Product Family?
The current CellPipe 20 Series Product Family consists of two groups of
products—symmetrical digital subscriber line (SDSL) and asymmetrical digital
subscriber line (ADSL)—for Point-to-Point Protocol (PPP) or Frame Relay over
asynchronous transfer mode (ATM). All units support IP bridging and routing.
See Table 1-1 for a summary of the features for each product.
Table 1-1. CellPipe 20 Series products
CellPipe units
Description
CellPipe 20A-GX
Support for:
•
•
•
•
•
ADSL Annex A mode operation
G.Lite interface
DMT line code
IP routing and bridging, PPP support
Asymmetrical transmission with downstream
rates of 64Kbps to 8Mbps and upstream rates of
64Kbps to 1Mbps
•
•
•
One 10BaseT Ethernet port
Eight PVCs in bridging mode
Five PVCs in routing mode
CellPipe 20S
Support for:
•
•
•
•
SDSL transmission
IP routing and bridging, PPP support
2B1Q line code
Symmetrical transmission rates in the range of
144Kbps to 2.32Mbps
•
•
•
Integrated four-port 10BaseT Ethernet hub
Eight PVCs in bridging mode
Five PVCs in routing mode
1-2
CellPipe™ 20 Series User’s Guide
Introduction
Lucent TURN-UP
Lucent TURN-UP
The CellPipe 20 Series Product Family supports the Lucent TURN-UP™ automated
CPE provisioning system. TURN-Up is enabled when a user powers up his unit and
allows service providers to quickly and efficiently distribute and provision CPE gear
without the use of truck-rolls. Furthermore, TURN-UP stores configuration
information on a central server, making configuration management efficient and easy.
Caution: If you attempt to manually configure the unit, TURN-UP will be disabled.
To re-enable TURN-UP, you need to select the defaultcommand and reinstall the
factory default configuration.
!
CellPipe 20 Series management
CellPipe 20 Series units can be managed via three different connections:
Console port
Ethernet port
WAN port
•
•
•
CellPipe 20 series units are managed through a command-line interface (CLI). Also,
rudimentary management can be accomplished with SNMP. You set up a connection
between your computer and the device and use VT100 emulation software to display
and change configuration information. See Chapter 3, “Command-Line Interface,”
for a description of all the commands in the command-line interface.
CellPipe™ 20 Series User’s Guide
1-3
Setup
Verifying package contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Items you need for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Connecting CellPipe 20 Series products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Checking status lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Console setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Prior to setting up your unit, verify the contents of the package for your unit against
the package-contents list provided in this chapter. After determining the contents are
complete, connect the cables, verify all status lights are operating properly, and
establish a serial connection from you computer to the unit.
Verifying package contents
Verify the contents of the CellPipe 20 Series package you receive.
The CellPipe 20 Series package contains the following items:
•
•
•
CellPipe unit
10BaseT Ethernet cable (yellow)
WAN cable with RJ11 connector (blue)
CellPipe™ 20 Series User’s Guide
2-1
Setup
Items you need for installation
•
•
Power supply
Warranty card
Note: All CellPipe units are shipped with a power supply. However, European users
need to purchase an additional wall-outlet cable because of regional variations in wall
outlets. Please check with your sales representative for the item specific to your unit.
Figure 2-1. Power supplies
European
power supply
U.S., Asia, Australia
power supply
Items you need for installation
following item:
•
An ethernet network interface card (NIC) for your PC
Connecting CellPipe 20 Series products
Figure 2-2 on page 2-3 shows the rear panel for each model. There are many
similarities between the units and the procedure for connecting the units are quite
similar as well.
2-2
CellPipe™ 20 Series User’s Guide
Setup
Connecting CellPipe 20 Series products
Figure 2-2. CellPipe 20 Series rear panels
CellPipe 20A-GX
CellPipe 20S
To connect up the CellPipe 20 Series units, proceed as follows:
1
LAN connections:
•
On the CellPipe 20A-GX, use the provided Ethernet cable (yellow) to
connect the ETHERNET port to the NIC on a computer or to an appropriate
networking component.
•
On the CellPipe 20S, use the provided Ethernet cables to connect the four
LAN ports (1X, 2X, 3X, 4X) to NICs on computers or to appropriate
networking components.
2
3
WAN connections:
•
Use the blue WAN cable to connect the WAN port to a wall xDSL connector
set up by your service provider.
Connect the power cable and power up the unit.
Note: Apply power last. Doing so turns on the unit, which does not have a power
switch.
CellPipe™ 20 Series User’s Guide
2-3
Setup
Checking status lights
Checking status lights
Observe the activity pattern of the lights at the front of the CellPipe units to verify that
they are connected properly.
Figure 2-3. Status lights
When all the cables are connected, verify that:
•
The pwrlight comes on initially and remains on. If not on, make sure the power
supply is properly connected.
•
•
The actlight blinks during any LAN traffic. Otherwise it remains off.
The lnklight is on if there is an Ethernet connection established. If not on,
check to make sure your Ethernet cable is properly connected.
•
•
The wanlight blinks until a connection is established and then it remains on.
The conlight is on only during the unit self-test.
Console setup
You need to set up a serial connection between the unit and your computer to access
the command-line interface and configure a CellPipe 20 Series unit.
You need a 9-pin RS-232 serial cable to connect to the CellPipe unit through the
console port.
You also need a terminal emulation program, such as HyperTerminal, PROCOMM
PLUS, Zterm, or any other program that supports VT100 terminal emulation, to open
a session directly with the unit.
2-4
CellPipe™ 20 Series User’s Guide
Setup
Console setup
Set your communications software to connect with the following settings:
•
•
•
•
•
•
•
•
•
Connection—Specify a direct connection from the unit to the computer.
Serial port—Specify the serial port on the computer the software is to use.
Terminal type—Specify VT100.
Duplex—Specify Full. This is the default for most communications software.
Bits per second—Specify 9600.
Data bits—Specify 8.
Parity—Specify None.
Stop bits—Specify 1.
Flow control—Specify None.
A >> prompt appears when the connection is completed.
CellPipe™ 20 Series User’s Guide
2-5
Command-Line Interface
Syntax of command-line interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Using the commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Bridging commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Routing commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
CellPipe 20 Series units are managed through a command-line interface (CLI). You
set up a connection between your computer and the unit and use VT100 emulation
software to display configuration information on your computer and input commands
and parameter values to configure and manage the unit.
Syntax of command-line interface
Syntax for the CLI is as follows:
•
•
•
•
•
•
>> prompt means commands can be entered without password
< > means the parameters are compulsory
[ ] means the parameters are optional
| between parameters means either/or
“...” around parameters means the enclosed are key words
A “space” is necessary between a command and its corresponding parameter
CellPipe™ 20 Series User’s Guide
3-1
Command-Line Interface
Using the commands
Using the commands
The CLI of the CellPipe 20 Series consists of two hierarchical levels. Some of the
second-level commands display values or status of the selected commands from the
main level.
Note: Access to the CLI is possible without a password. When user enables a
password, the unit will time-out after 10 minutes if there is no activity on the unit.
Re-entering password is necessary to resume activity.
The CellPipe 20 Series units display two sets of main menu commands based on the
mode of operation—bridging or routing. The default list of main menu commands is
for bridging. See “Bridging commands” on page 3-3. When selected for routing, the
routing menus are displayed. See “Routing commands” on page 3-6.
Viewing the main menu
To view a list of the main menu commands, enter helpat the >> prompt.
>> help
Displaying information about a command
To display information about a command, enter helpfollowed by the name of the
command.
For example, in the LAN menu, you can display information about the setip
command as follows:
>lan> help setip
setip
- setip <etherip[/<masknum>]> [subnet mask]
where etheripis the required information and [masknum] and [subnet
mask]are optional information.
3-2
CellPipe™ 20 Series User’s Guide
Command-Line Interface
Bridging commands
Returning to the main menu
To return to the main commands, enter the homecommand:
>lan> home
Displaying second-level commands
To select a second-level command, enter the command at the > prompt:
>adsl> show
Saving configurations
To save a value or configuration, enter the savecommand and type y:
>> save
Are you sure that you want to save the new changes?(y/n)y
Note: All settings have to be saved to take effect.
Bridging commands
The default main menu list of commands is for bridging. To display a list of bridging
commands, enter the helpcommand.
>> help
The following main menu commands are displayed for bridging mode:
xdsl*
- entry to xdsl menu
default - set all configuration to factory setting
lan
- entry to Ethernet
list
manage
mode
ping
quick
r1483
- list status for enabled PVC
- entry to management menu
- exit this menu and change modem mode
- ping IP for testing purpose
- quick setup
- entry to RFC 1483 menu
restart - reboot modem
CellPipe™ 20 Series User’s Guide
3-3
Command-Line Interface
Bridging commands
save
show
ver
- display configuration of PVC and Ethernet
- display software version
Note: *The WAN interface displayed in the menu is dependent on the interface
supported by your unit. This generic form of presentation has been arrived at to
eliminate the need of representing every interface.
Table 3-1 lists the main menu commands and their corresponding second-level
menus. The different WAN interfaces and their corresponding menus are presented in
sequence. Select the interface and menus appropriate to your unit.
Table 3-1. Main menu and second-level bridging commands
Main menu
Second-level menus/description
adsl
abort
bitdn
bitup
coding
- abort ADSL line
- ADSL downstream bit loading value
- ADSL upstream bit loading value
- <0>|<1>|<2>|<3>|<4>|<5>|<6>|<Auto> dB -
coding gain
counts
default
ec_fdm
rx_bin
show
- display ADSL counters
- reset to default ADSL setting
- <Ec>|<Fdm> - set EC or FDM mode
- <start_bin> <end_bin>
- display ADSL parameter configuration
- restart ADSL line
startup
status
stnl
- display ADSL line status
- <T1.413>|<g.Lite>|<g.Dmt>|<Multi Mode>
- <Enable>|<Disable> - Trellis encoding
- <0> .. <12> dB - Tx power attenuation
- <start_bin> <end_bin>
trellis
tx_pwr
tx_bin
3-4
CellPipe™ 20 Series User’s Guide
Command-Line Interface
Bridging commands
Table 3-1. Main menu and second-level bridging commands (continued)
Main menu
Second-level menus/description
sdsl
auto
cell
dbit
- <Enable>|<Fast>|<Scan>|<Disable>
- <Enable>|<Disable> idle-cell header
- configure the SDSL data bit as normal or reverse
polarity
default
enable
- set SDSL configuration back to factory setting
- activate the last updated SDSL parameters
maxrate - configure the SDSL autobuad max rate
rate - manually configure the SDSL line rate
scramble - <Enable>|<Disable> payload scrambling
smbit
status
- configure sign/magnitude bit sequence
- display the configuration and status of current
SDSL setting
terminal - configure modem to COE or CPE mode
set all configuration to factory setting
default
lan
fullduplex - fullduplex <Disable>|<Enable>
setip
- setup the IP address, and subnet mask for Ethernet
connection
show
- show LAN configuration
list
list status for enabled PVC
setpass - change password
manage
mode
please select bridge or router:(b/r,b)
ping IP
ping
quick (for adsl) R1483(r)/ IPoA(i)/ PPPoA(p)
quick (for sdsl) configure VPI/VCI
CellPipe™ 20 Series User’s Guide
3-5
Command-Line Interface
Routing commands
Table 3-1. Main menu and second-level bridging commands (continued)
Main menu Second-level menus/description
r1483 (for adsl) delpvc
- delete VPI and VCI
- set packet filter type
- set VPI and VCI for bridge mode
- set class
pfilter
setpvc
setqos
setspan - <Enable>|<Disable> spanning tree
show - show RFC1483 configuration
r1483 (for sdsl) delwanip - delete VPI and VCI
setqos - set class
setwanip - set PVC and Wan IP for routing mode
show - show RFC1483 configuration
restart
save
reboot modem
save and restart modem
show
display configuration of PVC and Ethernet
display software version
ver
Routing commands
You have to preselect for routing mode to have the routing commands display.
To select for routing, enter the modecommand and then enter rto select routing.
>>mode
Please select bridge or router:(b/r,b)r
3-6
CellPipe™ 20 Series User’s Guide
Command-Line Interface
Routing commands
The following main menu commands are displayed for routing mode:
xdsl* - entry to xdsl menu
default - set all configuration to factory setting
dnsrelay - entry to DNS Relay menu
ipoa
lan
- entry to IPoA menu
- entry to Ethernet
list
manage
mode
pat
- list status for enabled PVC
- entry to management menu
- exit this menu and change modem mode
- entry to PAT menu
ping
pppoa
quick
r1483
- ping IP for testing purpose
- entry to PPPoA menu
- quick setup
- entry to RFC 1483 menu
restart - reboot modem
rtable
save
show
ver
- entry to Routing Table menu
- save and restart modem
- display configuration of PVC and Ethernet
- display software version
Note: *The WAN interface displayed in the menu is dependent on the interface
supported by your unit. This generic form of presentation has been arrived at to
eliminate the need of representing every interface.
Most of the routing commands are similar to those under bridging mode. Table 3-2
lists only the additional routing commands and their corresponding second-level
menus that appear when routing is selected.
Table 3-2. Additional main-menu and second-level routing commands
Main menu
Second-level menus/description
dnsrelay
setdnsip
show
- set DNS server IP
- show DNS Relay configuration
CellPipe™ 20 Series User’s Guide
3-7
Command-Line Interface
Routing commands
Table 3-2. Additional main-menu and second-level routing commands (continued)
Main menu
Second-level menus/description
ipoa
delwanip
setqos
- delete IPoA PVC
- set class
setrip
- set IPoA PVC
setwanip
show
- set IPoA PVC
- show IPoA configuration
lan
dhcpclient - set dhcp client configuration
dhcpserver - set dhcp server configuration
fullduplex - fullduplex <Disable> | <Enable>
setdhcp
setip
- set dhcp operation
- setup the IP address, and subnet mask for
Ethernet connection
show
- show LAN configuration
pat
addpatin
delpatin
setpat
- add incoming PAT table
- delete incoming PAT table
- enable or disable PAT function
- show PAT configuration
show
pppoa
adduser
chpass
deluser
echo
- add user ID and password
- change user password
- delete user
- set echo interval time
- add LLC header on the packets
- set class
setllc
setqos
show
- show PPPoA configuration
r1483
delwanip
setqos
- delete VPI and VCI
- set class
setwanip
show
- set PVC and Wan IP for routing mode
- show RFC1483 configuration
3-8
CellPipe™ 20 Series User’s Guide
Command-Line Interface
Routing commands
Table 3-2. Additional main-menu and second-level routing commands (continued)
Main menu
Second-level menus/description
rtable
addiproute - add routing table
deliproute - delete routing table
show
- show routing table
CellPipe™ 20 Series User’s Guide
3-9
Auto-provisioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Configuring WAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Configuring LAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Configuring the manage command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Configuring the mode command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Configuring the quick command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Configuring the r1483 command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Configuring the dnsrelay command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Configuring the ipoa command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Configuring the pppoa command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Configuring the pat command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
This chapter provides general information for configuration of the various interfaces
and procedures for administering a CellPipe 20 Series unit.
Auto-provisioning
All CellPipe 20 Series units support the Lucent TURN-UP automated CPE
provisioning system. TURN-UP eliminates the need for user configuration of units
and provides centralized management of configuration information.
CellPipe™ 20 Series User’s Guide
4-1
Configuring a 20 Series CellPipe
Configuring WAN interface
When you power up the unit, it is set to default (factory settings) and the console will
display the following message:
Starting to download from remote server...
This means TURN-UP is enabled and is downloading the latest configuration
information.
To disable the feature, interrupt the download and manually configure the system.
To re-enable the feature, you need to select the defaultcommand and reinstall the
factory default configuration.
Configuring WAN interface
Currently the 20 Series units support SDSL and ADSL WAN interfaces.
SDSL commands and configurations
The following is a list of the menus available under the sdslcommand:
auto - <Enable>|<Fast>|<Scan>|<Disable> autobaud rate function
cell - <Enable>|<Disable> idle-cell header
dbit - configure the SDSL data bit as normal or reverse polarity
default - set SDSL configuration back to factory setting
enable - activate the last updated SDSL parameters
maxrate - configure the SDSL autobuad max rate
rate - manually configure the SDSL line rate
scramble - <Enable>|<Disable> payload scrambling
smbit - configure sign/magnitude bit sequence
status - display the configuration and status of current SDSL
setting
terminal - configure modem to COE or CPE mode
Select the autocommand to set values for autobaud rate function.
>sdsl> auto <Enable>|<Fast>|<Scan>|<Disable>
(Scan Rate: 2320, 1744, 1536, 1152, 768, 384, 192)
4-2
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring WAN interface
Select the cellcommand to enable or disable the idle-cell header.
>sdsl> cell <Enable|Disable>
Select the dbit command to configure the sdsl data bit.
>sdsl> dbit <Normal|Reverse>
Select the defaultcommand to set the SDSL configuration back to factory setting.
>sdsl> default
Set SDSL configuration back to factory setting
Select the enablecommand to activate the last updated SDSL parameters.
>sdsl> <enable > (null)
Select the ratecommand to manually configure the SDSL line rate.
>sdsl> rate - <n*8> (144 <= (n*8) <= 2320)
Select the maxrate command to configure the maximum SDSL autobaud rate. For
example:
>sdsl> maxrate
maxrate - configure the sdsl autobaud max rate
can use
2320K 1568K 1552K 1536K 1168K 1152K 1040K 784K
768K 528K 416K 400K 384K 272K 208K 192K
160K 144K
Select the ratecommand to manually configure the SDSL line rate. For example:
>sdsl> rate
rate
- configure the sdsl line rate
can use
2320K 1568K 1552K 1536K 1168K 1152K 1040K 784K
768K 528K 416K 400K 384K 272K 208K 192K
160K 144K
Select the scramble command to enable or disable payload scrambling.
>sdsl> scramble <Enable>|<Disable>
Select the smbit command to configure sign and magnitude bit sequence.
CellPipe™ 20 Series User’s Guide
4-3
Configuring a 20 Series CellPipe
Configuring WAN interface
>sdsl> smbit <Normal|Reverse>
Select the statuscommand to display the configuration and status of the current
SDSL setting. For example:
>sdsl> status
>version : Ver 2.31 Date 19/Feb/2001
terminal
auto
rate
- cpe
- enable
- 2320
maxrate
smbit
dbit
scramble
cell
- 2320
- reverse
- normal
- enabled
- disabled
Status :
Bitpump F/W Version : 5.1
Bitpump : present
CO/RT Select : cpe
Auto Rate : enable
Current Rate : 272
Max Rate : 2320
Sign/Magnitude Bit Sequence : reverse
Data Bit Polarity : normal
DSL Status : during startup
Line Quality : -16.0
Attenuation : 31.5
Select the terminalcommand to configure the modem to COE or CPE mode.
>sdsl> terminal <Coe>|<CPe>
ADSL commands and configurations
The following is a list of the menus available under the adslcommand:
abort
bitdn
bitup
- abort ADSL line
- ADSL downstream bit loading value
- ADSL upstream bit loading value
4-4
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring WAN interface
coding
counts
default
ec_fdm
rx_bin
show
- <0>|<1>|<2>|<3>|<4>|<5>|<6>|<Auto> dB - coding gain
- display ADSL counters
- reset to default ADSL setting
- <Ec>|<Fdm> - set EC or FDM mode
- <start_bin> <end_bin>
- display ADSL parameter configuration
- restart ADSL line
startup
status
stnl
- display ADSL line status
- <T1.413>|<g.Lite>|<g.Dmt>|<Multi Mode>
- <Enable>|<Disable> - Trellis encoding
- <0> .. <12> dB - Tx power attenuation
- <start_bin> <end_bin>
trellis
tx_pwr
tx_bin
Select the abortcommand to abort the ADSL connection.
>adsl> abort
Abort ADSL connection
Select the bitdncommand to obtain the downstream bit loading value.
>adsl> bitdn
Select the bitupcommand to obtain the upstream bit loading value.
>adsl> bitup
Select the codingcommand to set the ADSL coding gain:
>adsl> coding - <0>|<1>|<2>|<3>|<4>|<5>|<6>|<Auto> dB - coding
gain
Select the defaultcommand to set the ADSL configuration back to factory setting.
>adsl> default
Set ADSL configuration back to factory setting
Select the ec_fdmcommand to configure the ADSL link for echo cancellation or
frequency division multiplexing (FDM).
>adsl> ec_fdm <Ec>|<Fdm>
CellPipe™ 20 Series User’s Guide
4-5
Configuring a 20 Series CellPipe
Configuring WAN interface
Select the rx_bin command to limit the bin number used for special configurations
in the receive signal. Values for bin numbers are between 1 to 255.
>adsl> rx_bin - <start_bin> <end_bin>
Select the showcommand to display the ADSL parameter configuration. For
example:
>adsl> show
ADSL setting:
Local line code
Trellis encoding
EC/FDM mode
Coding gain
Current
Ineffective
MULTIMODE
Enabled
FDM
MULTIMODE
Enabled
FDM
AUTO
2 dB
Transmit Power Attenuation 0 dB
0 dB
Tx Start bin
Tx End bin
Rx Start bin
Rx End bin
6 (H)
6 (H)
1f (H)
3 (H)
4 (H)
1f (H)
20 (H)
ff (H)
Select the startupcommand to restart the ADSL connection.
>adsl> startup
start to re-Sync. ...
Select the statuscommand to display the ADSL parameter configuration. For
example:
>adsl> status
ADSL Firmware version ANNEX_A CPE 41000
OP state
handshake
Last Failed Status
Start Progress
Watchdog Timer
(0)
a0
53
Line code
Framing_Overhead_actual
Trellis
G.DMT
0
<disable>
AS0_Dn_Bytes_Actual
0
4-6
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring LAN interface
AS0_Dn_Latency_Actual
LS0_Up_Bytes_Actual
LS0_Up_Latency_Actual
Fast_R_Up_Actual
Interleave_S_Up_Actual
Interleave_D_Up_Actual
Interleave_R_Up_Actual
Fast_R_Dn_Actual
<interleave>
0
<interleave>
0
0
0
0
0
0
0
0
Interleave_S_Dn_Actual
Interleave_D_Dn_Actual
Interleave_R_Dn_Actual
Select the stnlcommand to configure the local ADSL coding type.
>adsl> stnl - <T1.413>|<g.Lite>|<g.Dmt>|<Multi-Mode>
Select the trelliscommand to enable or disable Trellis encoding.
>adsl> trellis <Enable>|<Disable>
Select the tx_pwrcommand to configure the transmitted power attentuation for a
range between 0 dB and 12 dB.
>adsl> tx_pwr <0> .. <12>
Select the tx_bin command to allow the user to limit bins used for special
configuration in the transmitted signal.
> adsl> tx_bin - <start_bin> <end_bin>
Configuring LAN interface
This section provides menus for configuring the LAN interface in both bridging and
routing mode.
Configuring LAN interface in bridging mode
The following is a list of the menus available under the lancommand in bridging
mode:
CellPipe™ 20 Series User’s Guide
4-7
Configuring a 20 Series CellPipe
Configuring LAN interface
fullduplex
setip
- fullduplex <Disable>|<Enable>
- setup the IP address, and subnet mask for
Ethernet connection
show
- show LAN configuration
Select the fullduplexcommand to enable or disable fullduplex.
>lan> fullduplex <Disable>|<Enable>
Select the setipcommand to set up the IP address and subnet mask for the LAN
link. For example:
>lan> setip 192.168.2.32
Set a new IP address = 192.168.2.32 and
Subnet mask is default = 255.255.255.0
Select the showcommand to display the current configuration of IP setting. For
example:
>lan> show
Ethernet IP = 192.168.2.32 and
Subnet mask is default = 255.255.255.0
FullDuplex : Disable
Configuring LAN interface in routing mode
The following is a list of the menus available under the lancommand in routing
mode:
dhcpclient
dhcpserver
fullduplex
setdhcp
- set dhcp client configuration
- set dhcp server configuration
- fullduplex <Disable>|<Enable>
- set dhcp operation
setip
- setup the IP address, and subnet mask for
Ethernet connection
show
- show LAN configuration
Select the dhcpclientcommand to set up the dhcp client configuration.
>lan> dhcpclient <lease time>
4-8
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring the manage command
Select the dhcpserver command to configure the range of IP addresses that are
associated with the subnet mask used for the DHCP server.
>lan> dhcpserver <range1 startIP> <range1 endIP> [<range2
startIP> <range2 endIP>] [<max-lease-time>]
- dhcpserver dns <dns ip1> [<dns ip2>]
Select the setdhcpcommand to set the DHCP mode of the unit.
>lan> setdhcp <server|client|disable>
Select the setipcommand to set the the IP address and subnet mask for the link.
>lan> setip <etherip[/<masknum>] [subnet mask]>|<dhcp>
Select the showcommand to display the LAN configuration. For example:
>lan> show
Ethernet ip: 149.198.65.46
Subnet mask: 255.255.255.0
FullDuplex:Enable
DHCP current setting : disable.
DHCP ineffective setting : disable.
Configuring the manage command
The managecommand allows you to set the user password. When user enables a
password, the unit will time out after 10 minutes if there is no activity. The password
has to be re-entered to resume activity.
>manage> setpass
Password disabled
New Password:<password>
Configuring the mode command
The modecommand allows you to select for either the bridging or the routing mode
of operation.
CellPipe™ 20 Series User’s Guide
4-9
Configuring a 20 Series CellPipe
Configuring the quick command
>>mode
Please select bridge or router:(b/r,r) <b|r>
Configuring the quick command
The quickcommand allows you to easily configure your LAN connections in either
the bridging or routing mode.
The quick command in bridging mode
The quickcommand in bridging mode allows you to easily configure eight PVCs.
For example:
>> quick
1 PVC existed, 7 PVCs available.
VPI(0-1023):8
VCI (0-65535):33
Packet Filter (Any/Ip/Pppoe): any
Add another PVC ? (y/n): n
Enable Spanning tree? (y/n) : y
The quick command in routing mode
The quickcommand in routing mode allows you to select the connection protocol
and set up the appropriate PVCs. For example:
>> quick
R1483(r)/ IPoA(i)/ PPPoA(p): r1483
0 PVC existed, 8 PVCs available.
Ethernet IP (149.198.65.46) :
Subnet mask (255.255.255.0) :
VPI(0-1023): 5
VCI(1-65535): 32
WAN IP : 149.198.6.46
Add another PVC ? (y/n): n
4-10
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring the r1483 command
>>quick
R1483(r)/ IPoA(i)/ PPPoA(p): ipoa
0 PVC existed, 8 PVCs available.
Ethernet IP (149.198.65.46) :
Subnet mask (255.255.255.0) :
VPI(0-1023): 5
VCI(1-65535): 33
WAN IP : 148.198.6.46
Gateway : 148.198.6.90
>>quick
R1483(r)/ IPoA(i)/ PPPoA(p): pppoa
0 PVC existed, 1 PVC available.
Ethernet IP (149.198.65.46) :
Subnet mask (255.255.255.0) :
VPI(0-1023): 5
VCI(1-65535): 34
Authentication( PAP(p)/CHAP(c)/None(n) ): p
User name: Lucent
Password: *******
Retype password: *******
Configuring the r1483 command
You can configure the r1483command for either bridging or routing mode.
The r1483 command in bridging mode
The following is a list of menus under the r1483command in the bridging mode:
delpvc
pfilter
setpvc
setqos
- delete VPI and VCI
- set packet filter type
- set VPI and VCI for bridge mode
- set class
CellPipe™ 20 Series User’s Guide
4-11
Configuring a 20 Series CellPipe
Configuring the r1483 command
setspan
show
- <Enable>|<Disable> spanning tree
- show RFC1483 configuration
Select the delpvccommand to delete one or all PVCs.
>r1483> delpvc <all>|[<vpi>/]<vci>
Select the pfiltercommand to set the packet filter type.
>r1483> pfilter [<vpi>/]<vci> <any|ip|pppoe|igmp|none>
Select the setpvccommand to set the PVCs in bridging mode.
>r1483> setpvc [<vpi>/]<vci> [llc/vcmux]
Select the setqoscommand to set the class for quality of service.
>r1483> setqos [<vpi>/]<vci> <ubr|cbr|vbr(nrt)>
Select the showcommand to display the RFC1483 configuration.
FUNCTION VPI/VCI
Rfc1483 8/35
CLASS LLC/VCMUX Spanning Pkt Filter
ubr LLC Enable ANY
The r1483 command in routing mode
The following is a list of menus under the r1483command in the routing mode:
delwanip - delete VPI and VCI
setqos
setrip
- set class
- set RIP configuration
setwanip - set PVC and Wan IP for routing mode
show - show RFC1483 configuration
Select the delwanipcommand to delete one or all PVCs.
>r1483> delpvc <all>|[<vpi>/]<vci>
Select the setqoscommand to set the class for quality of service.
>r1483> setqos [<vpi>/]<vci> <ubr|cbr|vbr(nrt)>
Select the setripcommand to set the PVC for RIP.
>ipoa> setrip [<vpi>/]<vci> <1|2|1&2|0>
4-12
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring the dnsrelay command
Select the setwanipcommand to set PVC and the IP address for routing.
>r1483> setwanip [<vpi>/]<vci> <wanip[/<masknum>]>
Select the showcommand to display the RFC1483 configuration.
> r1483> show
RFC1483 setting:
FUNCTION VPI/VCI
CLASS Wan IP/MaskNum
Configuring the dnsrelay command
The following is a list of menus available under the dnsrelaycommand:
setdnsip
show
- set DNS Server IP
- show DNS Relay configuration
Select the setdnsipcommand to set the IP address of the DNS server.
>dnsrelay> setdnsip <dnsip> [<retry times>]
Select the showcommand to display the DNS Relay configuration.
>dnsrelay> show
DNS server ip: 192.168.2.65
Retry times: 3
DNS relay status
Configuring the ipoa command
The following is a list of menus available under the ipoacommand>
delwanip
setqos
setrip
setwanip
show
- delete IPoA PVC
- set class
- set IPoA PVC
- set IPoA PVC
- show IPoA configuration
Select the delwanipcommand to delete one or all (8) IPoA PVCs.
>ipoa> delpvc <all>|[<vpi>/]<vci>
CellPipe™ 20 Series User’s Guide
4-13
Configuring a 20 Series CellPipe
Configuring the pppoa command
Select the setqoscommand to set the class for quality of service.
>ipoa> setqos [<vpi>/]<vci> <ubr|cbr|vbr(nrt)>
Select the setripcommand to set the PVC for RIP.
>ipoa> setrip [<vpi>/]<vci> <1|2|1&2|0>
Select the setwanipcommand to set up to eight PVCs, the WAN IP addresses for
each PVC, and the gateway IP address.
>ipoa> setwanip [<vpi>/]<vci> <wanip[/<masknum>]> <gatewayip>
Select the showcommand to display the IPoA configuration.
> ipoa> show
IPoA setting:
FUNCTION VPI/VCI CLASS Wan IP/MaskNum GatewayIP RIP
Configuring the pppoa command
The following is a list of the menus available under the pppoacommand:
adduser
chpass
deluser
echo
setllc
setqos
setrip
show
- add user ID and password
- change user password
- delete user
- set echo interval time
- add LLC header on the packets
- set class
- set RIP configuration
- show PPPoA configuration
Select the addusercommand to set up a PVC, user ID, and select an authentication
protocol for a user.
>pppoa> adduser [<vpi>/]<vci> <userid> [<chap|pap>]
Select the chpasscommand to change the password for the user of a pppoa
connection.
>pppoa> chpass
Old Password:******
New Password:******
4-14
CellPipe™ 20 Series User’s Guide
Configuring a 20 Series CellPipe
Configuring the pat command
Confirm Password again: ******
Pass has been changed
Select the delusercommand to delete a user of a pppoa connection.
>pppoa> deluser
Select the echocommand to input the echo time interval and enable LCP echo
cancellation.
>pppoa> echo <interval time>
Select the setllccommand to enable or disable logic link control (LLC).
>pppoa> setllc <e>nable|<d>isable
Select the setqoscommand to set the class for quality of service.
>pppoa> setqos [<vpi>/]<vci> <ubr|cbr>
Select the setripcommand to set up for RIP.
>pppoa> setrip <1|2|1&2|0>
Select the showcommand to display the PPPoA routing setting.
>pppoa> show
PPPoA dial out setting:
Function
PPPoA
VPI/VCI Class
2/32 ubr
PCR (Kbits)
640
UserID/Auth
Lucent/CHAP
LLC = Disable
Echo interval time: 60 s
Configuring the pat command
The following is a list of the menus available under the patcommand:
addpatin - add incoming PAT table
delpatin - delete incoming PAT table
setpat
show
- enable or disable PAT function
- show PAT configuration
CellPipe™ 20 Series User’s Guide
4-15
Configuring a 20 Series CellPipe
Configuring the pat command
Select the addpatincommand to enable a local server’s IP address to be used as a
WAN access port.
>pat> addpatin <pppoa|wanip> <port>/<udp|tcp> <serverip>
Note: Prior to setting the local server as a WAN access port, you have to enable the
PAT function. See the setpatcommand below.
Select the delpatincommand to disable the local server as a WAN access port.
>pat> delpatin <all>|<number>
Select the setpatcommand to enable or disable a specific PAT interface.
>pat> setpat <pppoa|wanip> <e>nable|<d>isable
Select the showcommand to display the Pat configuration.
>pat> show
PAT enabled interface:
Interface IP address
IPoA 210.62.2.195
PPPoA?.?.?.?
PAT incoming table
No. i/f name|WAN IP
Port/Protocol
434/udp
232/tcp
Server IP
192.62.2.134
192.62.2.166
1
2
pppoa
210.62.2.195
4-16
CellPipe™ 20 Series User’s Guide
Preparing to upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Obtaining software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Upgrading software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Preparing to upgrade
To upgrade system software for a CellPipe 20 Series unit, you need to download to
your computer the appropriate zipped file of the latest software release. Establish a
serial connection between the unit and your computer for access to the CLI and also
establish an Ethernet connection to the unit. Be sure the unit and your computer are
configured properly so that you can successfully “ping” the unit from your computer
or vice versa.
Obtaining software
You can obtain the latest software release from the Lucent Technologies eSight™
Service Center at http://www.esight.com.
Note: Be sure you use the correct loads to upgrade. Your unit can lose all or part of
its configuration if the wrong loads are used.
Caution: Do not upgrade to an earlier software version. Newer units will not
function properly when older software is loaded.
!
CellPipe™ 20 Series User’s Guide
5-1
Upgrading System Software
Upgrading software
Upgrading software
Follow the procedure below to upgrade software:
1
2
3
Extract the loads from eSight to your computer.
Establish an Ethernet connection between the unit and your computer.
Set up IP addresses on the unit and your computer such that you can successfully
ping the unit.
4
5
Under the DOS prompt on your computer, enter the path to the directory
containing the extracted loads and a file named xupgrade.bat.
To start the upgrade, execute command xupgrade <ipaddress of
unit>, for example:
C:\> xupgrade 149.198.65.46
Note: There is no need to back up your current configuration. Using the
xupgrade.bat file for upgrading will retain your current configuration. The
upgrading process might last as long as 60 seconds.
6
7
Then enter the restartcommand to reboot the unit.
Lastly enter the savecommand to save the new upgrade.
Note: Maintain stable power to the unit while upgrading software. If power fails
during the upgrading process, contents in the memory could be destroyed and the
system will hang and no longer function.
5-2
CellPipe™ 20 Series User’s Guide
Warranties and FCC Regulations
Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
FCC Part 15 Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
IC CS-03 Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Product warranty
1
Lucent Technologies warrants that the CellPipe unit will be free from defects in
material and workmanship for a period of twelve (12) months from date of
shipment.
2
Lucent Technologies shall incur no liability under this warranty if:
–
–
The allegedly defective goods are not returned prepaid to Lucent
Technologies within thirty (30) days of the discovery of the alleged defect
and in accordance with Lucent Technologies’ repair procedures; or
Lucent Technologies’ tests disclose that the alleged defect is not due to
defects in material or workmanship.
3
4
Lucent Technologies’ liability shall be limited to either repair or replacement of
the defective goods, at Lucent Technologies’ option.
Lucent Technologies MAKES NO EXPRESS OR IMPLIED WARRANTIES
REGARDING THE QUALITY, MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE BEYOND THOSE THAT APPEAR IN THE
APPLICABLE Lucent Technologies USER'S DOCUMENTATION. Lucent
Technologies SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL,
INCIDENTAL, OR PUNITIVE DAMAGE, INCLUDING, BUT NOT
LIMITED TO, LOSS OF PROFITS OR DAMAGES TO BUSINESS OR
CellPipe™ 20 Series User’s Guide
A-1
Warranties and FCC Regulations
FCC Part 15 Notice
BUSINESS RELATIONS. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES.
Warranty repair
1
During the first three (3) months of ownership, Lucent Technologies will repair
or replace a defective product covered under warranty within twenty-four (24)
hours of receipt of the product. During the fourth (4th) through twelfth (12th)
months of ownership, Lucent Technologies will repair or replace a defective
product covered under warranty within ten (10) days of receipt of the product.
The warranty period for the replaced product shall be ninety (90) days or the
remainder of the warranty period of the original unit, whichever is greater.
Lucent Technologies will ship surface freight. Expedited freight is at customer’s
expense.
2
The customer must return the defective product to Lucent Technologies within
fourteen (14) days after the request for replacement. If the defective product is
not returned within this time period, Lucent Technologies will bill the customer
for the product at list price.
Out-of warranty repair
Lucent Technologies will either repair or, at its option, replace a defective product not
covered under warranty within ten (10) working days of its receipt. Repair charges
are available from the Repair Facility upon request. The warranty on a serviced
product is thirty (30) days measured from date of service. Out-of-warranty repair
charges are based upon the prices in effect at the time of return.
FCC Part 15 Notice
Warning: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, uses, and can radiate
radio frequency energy, and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is unlikely to cause harmful
!
A-2
CellPipe™ 20 Series User’s Guide
Warranties and FCC Regulations
IC CS-03 Notice
interference. But if it does, the user will be required to correct the interference at his
or her own expense.
The authority to operate this equipment is conditioned by the requirement that no
modifications will be made to the equipment unless the changes or modifications are
expressly approved by Lucent Technologies.
IC CS-03 Notice
The Industry Canada label identifies certified equipment. This certification means
that the equipment meets certain telecommunications network protective, operational,
and safety requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The Department does not guarantee that the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should make sure that it is permissible to be
connected to the facilities of the local telecommunications company. An acceptable
method of connection must be used to install the equipment. The customer should be
aware that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be coordinated by a representative designated
by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request
the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines, and internal metallic water pipe system, if present,
are connected together. This precaution may be particularly important in rural areas.
Warning: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
CellPipe™ 20 Series User’s Guide
A-3
|