PAP2 Phone Adapter
Installation Guide
OUTBOUND CALLING
Version 1.0
DocVersion: PAP2-IG-v1-0-042805
Linksys PAP2 Installation Guide
Table of Contents
1
2
Introduction................................................................ 1
Adapter Description .................................................... 2
2.1 PAP2 Overview ..............................................................2
2.2 Connectors and Pinouts...................................................2
2.3 Accessing the PAP2 ........................................................2
3.
Provisioning ................................................................ 4
3.1 General Configuration for Outbound Calling........................4
3.2 Line-Specific Configuration ..............................................5
Page i
Linksys PAP2 Installation Guide
1 Introduction
This document is an installation/configuration guide for the Linksys PAP2 phone adapter
running firmware version 2.0.10 (LSc). It describes how to configure the SIP parameters,
codec settings and analog coefficients for outbound calling. It also includes steps for
provisioning the device with the user account and PIN. Once you complete these steps,
you will be ready to begin placing calls.
Page 1
Linksys PAP2 Installation Guide
2 Adapter Description
The sections below briefly describe the PAP2 device.
2.1 PAP2 Overview
The PAP2 is a 2-port FXS phone adapter, which allows you to connect two (2) analog
phones.
PAP2 2-Port FXS Phone Adapter
2.2 Connectors and Pinouts
The image below displays the Ethernet (RJ-45) and analog (RJ-11) line pin-outs.
Ethernet (RJ-45) and Analog (RJ-11) Line Pin-Outs
2.3 Accessing the PAP2
1. Connect an analog phone to the RJ-11 connector on the PAP2.
2. Using the telephone keypad, press the star key (*) four (4) times: ****.
You will be prompted to enter a code.
3. Enter the appropriate code, followed by the pound (#) key. Refer to the PAP2
Menu Options table on the following page for codes.
Page 2
Linksys PAP2 Installation Guide
PAP2 MENU OPTIONS
User Input
Action
Code
Behavior Notes
Enter IVR Menu
****
None
Do not press any other keys
until you hear, “Configuration
menu. Please enter option
followed by the pound (#)
key, or hang up to exit.”
Check DHCP
Set DHCP
100
101
None
The system announces if
DHCP is enabled or disabled.
Enter 1 to enable.
Enter 0 to disable.
Enter the option, followed by
the pound (#) key.
Check IP
address
110
111
None
Set IP Address
Enter value using the
numbers on the
Enter the value, followed by
the pound (#) key. DHCP
must be “Disabled,”
telephone keypad. Use
the star (*) key when
otherwise you will hear the
entering a decimal point. announcement, “Invalid
Option” if you try to set this
value.
Check Net Mask
Set Net Mask
120
121
None
Enter value using the
numbers on the
telephone keypad. Use
Enter the value, followed by
the pound (#) key. DHCP
must be “Disabled,”
the star (*) key when
otherwise you will hear the
entering a decimal point. announcement, “Invalid
Option” if you try to set this
value.
Check Gateway
Set Gateway
130
131
None
Enter the value using the Enter the value, followed by
numbers on the
telephone keypad. Use
the pound (#) key. DHCP
must be “Disabled,”
the star (*) key when
otherwise you will hear the
entering a decimal point. announcement, “Invalid
Option” if you try to set this
value.
Check MAC
Address
140
None
You will hear the phone
adapter’s MAC address.
Check Firmware
Version
150
None
None
You will hear the phone
adapter’s firmware version.
Manual Reboot
7326668
After you hear, “Option
successful,” hang up the
phone. The phone adapter
will automatically reboot.
PAP2 Menu Options
Page 3
Linksys PAP2 Installation Guide
3. Provisioning
3.1 General Configuration for Outbound Calling
To configure the PAP2 for outbound calling:
1. Connect to the PAP2 by entering the device’s IP address in the Web browser’s
Address bar. For instructions on obtaining the IP address, refer to section 2.3
Accessing the PAP2 on page 2 in this Guide.
2. Click on the Admin Login link in the upper right corner of the page, and then
click the advanced configuration link.
PAP2 Web Interface – Main Window
3. Click the System tab, and in the Internet Connection Type section, click the
DHCP drop-down menu, and select yes or no.
System Tab
4. If you set DHCP to no, enter the Static IP, NetMask, and Gateway information.
If you set DHCP to yes, continue to step 5.
5. Click the Submit All Changes button at the bottom of the page to save the
settings.
Page 4
Linksys PAP2 Installation Guide
3.2 Line-Specific Configuration
1. Click the Line1 or Line2 tab at the top of the page, and in the NAT Settings
section, change the following setting:
Field
Value
no
NAT Keep Alive Enable
2. In the Proxy and Registration section (see the screen on the following page),
change the following settings:
Field
Value
Proxy
byod1.net2phone.com
Use Outbound Proxy
Use OB Proxy In Dialog
Make Call Without Reg
Ans Call Without Reg
DNS SRV Auto Prefix
no
no
yes
yes
no
3. In the Subscriber Information section (as shown in the Line1/2 Window screen on
the following page), enter a Display Name. This value can be any alphanumeric
string. Enter the following values for outbound only service:
Service Type
Field
Display Name
Value
Display Name (Line 1)
Display Name (Line 2)
NO_DID1
NO_DID2
OUTBOUND SERVICE ONLY
4. Enter the User ID (account) and Password (PIN).
IMPORTANT You must have a different account and PIN for Line 1 and Line 2.
5. Click the Use Auth ID drop-down menu, and click no.
Page 5
Linksys PAP2 Installation Guide
Proxy and Registration and Subscriber Information Sections
6. Scroll to the Audio Configuration section (as shown in the Audio Configurations
and Dial Plan Sections screen on the following page), and change the following
settings:
Field
Value
Preferred Codec
Use Pref Codec Only
G729a Enable
G729a
no
yes
yes
no
G723 Enable
G726-16 Enable
G726-24 Enable
G726-32 Enable
G726-40 Enable
DTMF Tx Method
no
no
no
AVT
Page 6
Linksys PAP2 Installation Guide
Audio Configuration and Dial Plan Sections
7. In the Dial Plan section, change the Dial Plan to fit the dialing pattern in your
country. The dialed number must start with ‘1’ for US calls and ‘011’ for non-US
calls. Please read the PAP2 manual to customize your dial plan.
8. Click the Submit All Changes button to save the settings.
Page 7
|