Liebherr Refrigerator CS 1601 User Manual

Design Guide 2008  
Freestanding / Semi Built In Models 30", 36" and 60"  
 
Welcome  
Liebherr's engineering excellence in Germany provides the largest  
selection of freezers, refrigerators and wine refrigerators worldwide.  
Liebherr-appliances consistently specializes in the manufacturing of high  
quality freezers and refrigerators. With more than 300 basic models, we have  
the widest selection in the world. Liebherr appliances feature premium quality,  
numerous innovative product ideas and advanced design. Liebherr freezers and  
refrigerators are manufactured at three modern production plants:  
Liebherr Marica in Bulgaria, Liebherr-Hausgeräte Ochsenhausen GmbH in  
Germany and the Liebherr-Hausgeräte Lienz GmbH in Austria.  
We produce more than 2.3 million quality freezers, refrigerators and wine  
refrigerators each year, and these are sold all over the world. Liebherr-  
Hausgeräte Ochsenhausen GmbH in Germany makes over 1,100,000 appliances  
a year and employs 1,900 people. The Liebherr-Hausgeräte Lienz GmbH  
manufactures more than 700,000 freezers and refrigerators and employs 1,500  
people.  
The appliances for the North American market are produced in Austria and in  
Germany.  
Liebherr is commited to the protection of the environment and recognizes it  
as a critical priority. To guarantee an optimum and consistent implementation,  
all ecological aspects were observed and integrated into the quality control of  
Liebherr in compliance with DIN EN ISO 9001.  
Liebherr's Commitment to the Environment  
The components of Liebherr products can be recycled when the necessary  
resources are applied. A concern for the environment and a desire to protect  
resources has lead to increased levels of recycling year after year. When  
Liebherr manufactures products, it is essential that the recyclable recovery rate  
of the materials we use constantly increases.  
Recycling is a common goal among all manufacturers, municipalities and  
recycling companies to protect our environment. Protecting the environment  
and producing products which have a low impact on the environment, is one  
of Liebherr's core values. Whether you are replacing a unit or starting fresh,  
remember to dispose of your old appliance in an environmentally safe and  
friendly manner.  
 
Introduction  
LIEBHERR WARRANTY PLAN  
FULL TWO YEAR WARRANTY - For two years from the date of original purchase, your Liebherr Warranty  
covers all parts and labor to repair or replace any part of the product which proves to be defective in mate-  
rials or workmanship.  
FULL FIVE YEAR WARRANTY - For five years from the date of original purchase, your Liebherr Warranty  
covers all parts and labor to repair or replace any components that prove to be defective in materials or  
workmanship in the sealed system. The "Sealed System" means only the compressor, condenser, evapo-  
rator, drier and all connecting tubing.  
LIMITED 6TH THROUGH 12TH YEAR WARRANTY - From the 6th through 12th year from the date of  
original purchase, your Liebherr Warranty covers all parts that prove to be defective in materials or work-  
manship in the sealed system (parts only).  
For Service and Parts in the U.S.:  
Liebherr Service Center  
15545 N. 77th Street  
Scottsdale, AZ 85260  
Customer Service  
If your appliance is not working properly, or if the tem-  
Phone:  
Fax:  
(480) 998-0141  
(480) 998-7877  
perature display reads "F0" to "F5”, please call the  
numbers listed below.  
Toll Free:  
1-866-LIEBHERR or  
1-866-543-2437  
Give the fault number displayed, together with the  
Type Designation,  
Service Number and  
Appliance Number (Serial Number)  
from the model plate, to ensure prompt, accurate servic-  
ing. The model plate is located inside the appliance.  
For Service and Parts in Canada:  
Euro Parts  
579 Campbell Street,  
P.O. Box 759,  
Leave the appliance door closed until the customer ser-  
vice technician arrives to minimize any further cold loss.  
Lucknow, Ontario, N0G 2H0  
Phone:  
Fax:  
(519)528-5005  
(519)528-5001  
Toll Free:  
1-888-Liebherr or  
1-888-543-2437  
 
Contents  
General Remarks  
Safety Warnings  
I
Electrical Requirements & Safety  
II  
IceMaker (if equipped)  
Area Requirements  
Safety Regulations  
III  
IV  
V
1
3
5
Ventilation Requirements  
7
9
11  
 
 
General Remarks  
I. Safety Warnings  
PLEASE READ AND FOLLOW THESE INSTRUCTIONS  
This design guide contains Warning and Caution statements. This information is important for safe and  
efficient installation.  
This design guide is not replacing the use and care manual which contains important information on how to use Lieb-  
herr appliances.  
Always read and follow all Warning and Caution statements!  
States a hazard that may cause serious injury or death if precautions are not followed.  
Signals a situation where minor injury or product damage may occur if you do not follow instructions.  
States a hazard will cause serious injury or death if precautions are not followed.  
IMPORTANT  
This highlights information that is especially relevant to a problem-free installation.  
Make sure incoming voltage is the same as the unit rating.  
To reduce the risk of fire, electric shock, or personal injury, the installation work and electrical wiring must be done by  
a qualified electrician in accordance with all applicable codes and standards, including fire rated construction.  
To the Installer  
It is very important that the guidelines and instructions are followed in this design guide to ensure proper installa-  
tion and operation of the unit. The Installation Guidelines section contains important information for making sure the  
installation is correct. Read and understand all the information and installation guidelines in this manual before the  
unit is installed.  
It is also very important to know the Safety Information.  
 
General Remarks  
II. Electrical Requirements & Safety  
III. IceMaker (if equipped)  
A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-side  
installation) fused electrical supply is required. Connect  
undercounter wine cabinet to a 115 VAC, 10 amp (15  
Amp for side-by-side installations) circuit that is con-  
trolled by a circuit breaker or fuse.  
We recommend using a dedicated circuit for these ap-  
pliances to prevent electrical overload. Comply with  
the National Electrical Code as well as local codes and  
ordinances when installing the receptacle.  
The icemaker is located in the freezer compartment.  
It must be connected to the water supply to function  
properly. The appliance must be level for the icemaker to  
function properly.  
The water pressure must be between 21.8-87.0 psi (1.5-6 bar).  
Use a 1/4" OD copper line to connect the water supply to  
the solenoid valve. This is not supplied with the refrigera-  
tor.  
If you have hard water, we recommend you install a  
water softener. Also, a filter must be installed if the water  
contains solids such as sand. All equipment and devices  
used to supply the water to the appliance must comply  
with the current regulations for your geographical area.  
The power cord is equipped with a three-prong (ground-  
ing) plug for your protection against possible shock  
hazards. To maintain this protection:  
• Do not modify the plug by removing the round ground-  
ing prong.  
Safety Instructions and Warnings  
• Do not attach the water source while the appliance is  
connected to an electrical outlet.  
• Do not use a power cord that is frayed or damaged.  
• A shut-off valve, must be installed between the hose  
line and the main water supply so that the water sup-  
ply can be stopped if necessary. Do not install the  
shut-off valve behind the refrigeration unit.  
Do not ground to a gas pipe. Check with a  
qualified electrician if you are not sure the  
appliance is properly grounded. Do not have  
a fuse in the neutral or grounding circuit.  
• The connection to the water supply may only be made  
by a trained and licensed plumber.  
• The water quality must comply with the drinking water  
regulations for the geographical area where the appli-  
ance is located.  
ELECTROCUTION HAZARD  
Electrical Grounding Required. This  
appliance is equipped with a three-  
prong(grounding) polarized plug for your  
protection against possible shock hazards.  
• DO NOT remove the round grounding  
prong from the plug.  
• The icemaker is designed exclusively to make ice  
cubes in quantities needed by a household and may  
only be operated with water appropriate for this pur-  
pose.  
• DO NOT use a two-prong grounding  
adapter.  
• DO NOT use an extension cord to connect  
power to the unit.  
• All repairs and work on the icemaker may only be done  
by customer service personnel or other trained person-  
nel.  
• The manufacturer cannot accept liability for damage  
caused by equipment or water lines between the sole-  
noid valve and the water supply.  
 
General Remarks  
IV. Area Requirements  
V. Safety Regulations  
The appliance complies with UL250 and CAN/CSA-C  
22,2 No. 63 and is designed to cool, freeze, store food  
as well as make ice (if equipped). It is designed as a  
household appliance. If used commercially, the relevant  
regulations on commercial use must be observed.  
Verify the following:  
• Floors can support refrigerator’s weight plus approxi-  
mately 1200 pounds (544 kg) of food weight. Not  
all Liebherr products are designed for 1200 pounds  
(544 kg) of food. Some units are smaller and total  
weights may vary.  
The appliance is set to operate within specific ambient  
temperature limits according to its climate rating. These  
temperature limits should not be exceeded. The cor-  
rect climate rating for your appliance is indicated on the  
model plate.  
• Finished kitchen floor height is level. Refrigerator must  
be shimmed to the floor level, or levelled, to make  
sure, air vents are not obstructed.  
• Remove anything attached to the rear or side walls  
that can obstruct refrigerator opening.  
This is explained as follows:  
• Cutout dimensions are accurate.  
Climate  
Rating  
Set for Ambient Temperatures of  
• Electrical outlet is in correct location.  
SN  
N
50°F to 90°F (10°C to 32°C)  
61°F to 90°F (16°C to 32°C)  
61°F to 100°F (16°C to 38°C)  
61°F to 109°F (16°C to 43°C)  
50°F to 100°F (10°C to 38°C)  
50°F to 109°F (10°C to 43°C)  
Do not install this unit next to any other refrigerator or  
freezer except another Liebherr model. Liebherr models  
are designed to allow side by side installation. They are  
equipped with a heating system to eliminate condensa-  
tion when units are installed side by side. Installing this  
unit next to any other refrigerator or freezer can cause  
condensation or cause damage to the Liebherr unit.  
ST  
T
SN-ST  
SN-T  
- The refrigerant circuit has been tested for leaks.  
To protect the refrigerator from possible  
damage, allow the appliance to stand 1/2 to  
1 hour in place before turning the electricity  
on. This allows the refrigerant and system  
lubrication to reach equilibrium.  
Blocking For Safety  
The anti-tip bracket must be installed to prevent the unit  
from tipping after it is installed. Refer to chapter "Block-  
ing For Safety" in the installation instructions.  
 
Freestanding/Semi Built In Models  
CS 1601, 1650  
30", 36" and 60" Models: CS 16.., CS 2062, SBS 32S0  
The unique design of Liebherr's freestanding models feature fully stainless steel doors, and even stainless steel side walls - a per-  
fect combination of design and functionality.  
30" Models  
CS 1601  
Energy Star:  
qualified  
Energy consumption p. a.:  
Energy Supply:  
Total capacity:  
Refrigerator:  
Freezer:  
Climate Rating:  
Door hinges:  
460 kWh  
115V / 60Hz / 2.5A  
15.5 cu ft (438 L)  
11.3 cu ft (320 L)  
4.2 cu ft (118 L)  
SN-T  
left / reversible  
• Automatic refrigerator defrosting  
• Automatic freezer compartment defrosting  
CS 1650  
Energy Star:  
qualified  
Energy consumption p. a.:  
Energy Supply:  
Total capacity:  
Refrigerator:  
460 kWh  
115V / 60Hz / 2.5A  
15.4 cu ft (436 L)  
11.3 cu ft (320 L)  
4.1 cu ft (116 L)  
2.4 pd./24h  
3.3 pd.  
Freezer:  
Ice cube capacity:  
Ice cube stock:  
Climate Rating:  
Door hinges:  
SN-T  
right / reversible  
• Automatic refrigerator defrosting  
• Automatic freezer compartment defrosting  
• Automatic IceMaker can be switched off  
1
 
 
Freestanding/Semi Built In Models  
CS 2062, SBS 32S0  
36" and 60" Models  
CS 2062  
Energy Star:  
qualified  
452 kWh  
Energy consumption p. a.:  
Energy Supply:  
Total capacity:  
Refrigerator:  
115V / 60Hz / 2.5A  
19.5 cu ft (552 L)  
13.5 cu ft (382 L)  
6 cu ft (170 L)  
3 pd./24h  
Freezer:  
Ice cube capacity:  
Ice cube stock:  
Climate Rating:  
6 pd.  
SN-T  
• Automatic refrigerator defrosting  
• Automatic freezer compartment defrosting  
• Automatic IceMaker can be switched off  
SBS 32S0 (CS 1601 & CS 1650)  
Energy Supply:  
Total capacity:  
Refrigerator:  
115V / 60Hz / 5A  
30.9 cu ft (875 L)  
22.6 cu ft (640 L)  
8.3 cu ft (235 L)  
2.4 pd./24h  
3.3 pd.  
SN-T  
Freezer:  
Ice cube capacity:  
Ice cube stock:  
Climate Rating:  
Door hinges:  
left / right / reversible  
• Automatic refrigerator defrosting  
• Automatic freezer compartment defrosting  
• Automatic IceMaker can be switched off  
2
 
Freestanding/Semi Built In Models  
CS 1601, CS 1650, CS 2062  
Unit Dimensions - Freestanding Models  
Overall height can be increased on all CS 16  
units by 5/8" (16 mm) by adjusting the roller  
base.  
CS 1601, CS 1650  
A.  
B.  
C.  
D.  
E.  
F.  
2-1/4" (57.5 mm)  
81-11/32" (2066 mm)  
29-1/2" (750 mm)  
31-3/8" (797 mm)  
23-1/4" (590 mm)  
24-13/16" (630 mm)  
51-25/32" (1315 mm)  
G.  
Overall height can be increased on CS 20  
units by 1-1/2" (40 mm) by adjusting the roller  
base.  
CS 2062  
A.  
B.  
C.  
D.  
E.  
G.  
H.  
3-17/32" (90 mm)  
80-9/32" (2039 mm)  
35-13/16" (910 mm)  
13-9/16" (344 mm)  
24-7/32" (615 mm)  
40-13/16" (1037 mm)  
39-7/16" (1002 mm)  
Please allow for door swing clearance at  
locations next to a wall.  
3
 
 
Freestanding/Semi Built In Models  
SBS 32S0  
Overall height can be increased on SBS 32  
units by 5/8" (16 mm) by adjusting the roller  
base.  
SBS 32S0 (CS 1601 & CS 1650)  
A.  
B.  
C.  
D.  
E.  
F.  
2-1/4" (57.5 mm)  
81-11/32" (2066 mm)  
59-1/4" (1510 mm)  
63-3/16" (1604 mm)  
23-1/4" (590 mm)  
24-13/16" (630 mm)  
51-25/32" (1315 mm)  
G.  
4
 
 
Freestanding/Semi Built In Models  
CS 1601, CS 1650, SBS 32S0  
Cabinet Opening Dimensions - 30" and 60" Models  
The appliance can be integrated into the kitchen units. To  
adapt the appliance to the height of the row of kitchen units, a  
suitable top cupboard can be fitted above the appliance.  
Unit Venting  
DO NOT restrict the air flow. An air flow of at least 2" (50mm)  
must be provided. The opening can either be directly over the  
appliance or on the back of the cabinet on top of the unit (see  
ventilation requirements).  
Electric outlet location  
The CS models can be installed in standard 24" deep cabinets.  
You will only have to make sure that the door swing clearance  
is enough. It is possible to push all CS models to the rear wall  
of the cabinet without modification.  
When installing the appliance next to a wall, a distance on the  
hinge side of 1 27/64 inches (36 mm) minimum is required be-  
tween the appliance and the wall to allow for the door handle  
projection when the door is open.  
Minimum Cabinet Opening Dimensions:  
CS 1601, 1650  
A.  
B.  
C.  
D.  
29-7/8" (759 mm)  
23-3/16" (589 mm)  
85" (2159 mm)  
83-11/16" (2075 mm)*  
SBS 32S0 (CS 1601 & CS 1650)  
A.  
B.  
C.  
D.  
59-1/2" (1511 mm)  
23-3/16" (589 mm)  
85" (2159 mm)  
83-11/16" (2075 mm)*  
*Note:  
Water supply area.  
The given cabinet opening height dimension includes 2" for top  
air vent.  
If you choose to place the vent above the cabinet or in a soffit,  
you will need to adjust the height dimension accordingly.  
Do not install the  
shut-off valve behind  
the appliance.  
5
 
Freestanding/Semi Built In Models  
CS 2062  
Cabinet Opening Dimensions 36" Models  
The appliance can be used as freestanding or semi built-in.  
At semi built in please consider the cabinet opening dimensions.  
The requirements for water supply and electrical outlet are the same for both applications.  
IMPORTANT  
Do not install the shut-off  
valve behind the appliance.  
The position of the electrical  
outlet can be within the grey  
shaded areas or above the  
appliance.  
Water line opening  
Water supply line  
A.  
B.  
C.  
36" (914 mm)  
24" (610 mm)  
80-1/2" (2045 mm)  
IMPORTANT  
At 24" cabinets, the water line opening must be in the  
location as shown.  
IMPORTANT  
The free length of the water supply line must be at least  
31 - 1/2" (800 mm) when the tube comes out of the  
prescribed opening.  
At cabinets deeper than 24" there is room to fit the  
pipe behind the appliance and the wall so there are no  
requirements for the water line lead out position.  
6
 
CS 1601, 1650 - SBS 32S0  
Freestanding/Semi Built In Models  
Ventilation Requirements CS 1601, CS 1650, SBS 32S0  
This type of cabinet must be carefully constructed using the  
correct dimensions and it must provide suitable ventilation to  
ensure proper appliance operation.  
Kitchen Cabinet Airflow  
B - Side view  
1. The following ventilation dimensions must be observed:  
There must be a ventilation space at least 31 in.² (200 cm²)  
at the airflow inlet (1) and at the airflow outlet (2). The 30"  
and 60" models are equipped with a rolling base, which is  
already providing you with the bottom airflow inlet require-  
ments.  
Cabinet  
The top ventilation space can be directed in one of the fol-  
lowing ways:  
Refrigerator  
A) Directly over the appliance (2) with a gap of at least 2  
inches between the ceiling of the unit and the cabinet  
B) Above the cabinet and below the ceiling (3).  
C) Through a vent installed in a soffit (4).  
A
B
The refrigerator is designed to allow proper air flow when the  
appliance is installed up against the wall.  
A minimum space of 1 1/2" is required when a cabinet is built  
above.  
C
7
 
Freestanding/Semi Built In Models  
CS 2062,  
Ventilation Requirements CS 2062  
CS 20 appliances dont need any ventilation openings in the cabi-  
net. The required airflow is directed through the toe kick area.  
It is important to use the provided cover grille for the ventila-  
tion opening. This opening must not be covered with a cabinet  
base.  
8
 
 
Freestanding/Semi Built In Models  
CS 1601, 1650 - SBS 32S0  
Top Door Hinge Clearance CS 16.. - SBS 32S0  
When installing CS units into a row of cabinets or wall units;  
use these dimensions to achieve a custom look with the cabi-  
netry while providing the necessary clearance for the top door  
hinge.  
9
 
 
Freestanding/Semi Built In Models  
CS 2062,  
Top Door Hinge Clearance CS 2062  
When installing CS 20 units into a row of cabinets or wall units;  
use these dimensions to achieve a custom look with the cabi-  
netry while providing the necessary clearance for the top door  
hinge.  
Assuming centerline  
10  
 
Freestanding/Semi Built In Models  
Door Swing Clearance CS 2062  
Left side wall of appliance housing  
Top View  
Door closed  
11  
 
Freestanding/Semi Built In Models  
12  
 
Design Guide 2008  
Freestanding / Semi Built In Models 30", 36" and 60"  
 

La Crosse Technology Portable Radio WA 1240U User Manual
Land Pride Lawn Mower FDR2560 User Manual
Lenoxx Electronics Telephone PH 301 User Manual
LG Electronics TV Antenna 32 37 42 47 55LD6 User Manual
Lightolier Indoor Furnishings 1113IE User Manual
Lindy Switch No 39123 User Manual
Link electronic Portable Generator IEC 833 User Manual
Memorex MP3 Player MMP8500 User Manual
Metra Electronics Home Theater System 82 8141 User Manual
Micro Innovations Mouse KB575M User Manual