HEARTH PRODUCTS
KITS AND ACCESSORIES
750,235M
Rev. NC, 08/2006
EYEBROW LINTEL KITS
INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS
FOR USE WITH ELDV-35, ELDV-40 & ELDV-45 DIRECT VENT GAS FIREPLACES
KIT CONTENTS:
TOOLS NEEDED:
INSTALLATION INSTRUCTIONS
1 ea. Eyebrow
5/16” Nut Driver or Socket
#26 (.147") Drill Bit
Drill Motor
Step 1. Remove glass door assembly per the following instructions.
1 ea. Lintel
3 ea. #10 Screws
1 ea. Instruction Sheet
WARNING
Handle this glass with extreme care! The glass panel is
susceptibletodamage—donotscratchwhilehandling
or while re-installing the glass door frame.
Eyebrow Lintel Kits
CAT. NO.
H4387
H4388
H4389
MODEL NO.
WHERE USED
ELDV-35
ELDV35
ELDV40
ELDV45
ELDV-40
ELDV-45
WARNING
Table 1
Do not operate appliance with the glass front removed,
crackedorbroken. Replacementoftheglassshould be
done by a licensed or qualified service technician.
Lintel
HEARTH PRODUCTS
KITS AND ACCESSORIES
Glass Door Removal Procedure:
750,235M
Rev. NC, 07/2006
EYEBROW LINTEL KITS
INSTALLATION INSTRUCTIONS FOR EYEBROW LINTEL KITS
FOR USE WITH ELDV-35, ELDV-40
&
ELDV-45 DIRECT VENT GAS FIREPLACES
KIT CONTENTS:
TOOLS NEEDED:
INSTALLATION INSTRUCTIONS
1
1
3
1
ea. Eyebrow
5/16” Nut Driver or Socket
#26 (.147") Drill Bit
Drill Motor
ea. Lintel
Step 1. Remove glass door assembly per the following instrucitons.
ea. #10 Screws
ea. Instruction Sheet
WARNING
Eyebrow Lintel Kits
Handle this glass with extreme care! The glass panel is
CAT.
NO.
MODEL NO.
WHERE USED
ELDV-35
susceptibletodamage
—
donotscratchwhilehandling
or while re-installing the glass door frame.
ELDV-40
ELDV-45
Refer to Figure 2 and remove the front glass enclosure panel as
follows:
WARNING
Do not operate appliance with the glass front removed,
crackedorbroken. Replacementoftheglassshould be
done by licensed or qualified service technician.
T
able
1
a
Lintel
Glass Door Removal Procedure:
Refer to Figure
2
and remove the front glass enclosure panel as
follows:
Eyebrow
1. Removethebottomcompartmentdoorbyliftingandpullingittowards
the front of the fireplace.
2. Locate the two (2) latches at the top of the control compartment
and disengage them from the floor frame bottom Vee-flange, pulling
down on their handles to open them.
3. Swing the bottom of the door out and raise it slightly to lift the top
flange of the door frame away from the appliance.
Instruction Sheet
Figure Kit Contents
Screws
1
-
Eyebrow
IMPORTANT
WHEN APPLIANCE IS OFF AND COLD!
INSTALL ONL
Y
GENERAL INFORMATION
Theseeyebrowlintelkitsaredesignedtoprovideanaestheticallypleasing
appearance and conceal the gap above the fireplace.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
HOMEOWNER'S MANUALS PROVIDED WITH THE APPLIANCE APPL
Y
TO THESE INSTRUCTIONS.
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Door
Assembly
Bottom Panel
1. Removethebottomcompartmentdoorbyliftingandpullingittowards
the front of the fireplace.
2. Locate the two (2) latches at the top of the control compartment
and disengage them from the floor frame bottom Vee-flange, pulling
down on their handles to open them.
Figure
2
-
Glass Door Removal and Reinstallion.
NOTE: DIAGRAMS
&
ILLUSTRATIONS NOT TO SCALE.
Instruction Sheet
Screws
Figure 1 - Kit Contents
3. Swing the bottom of the door out and raise it slightly to lift the top
flange of the door frame away from the appliance.
IMPORTANT
INSTALL ONLY WHEN APPLIANCE IS OFF AND COLD!
GENERAL INFORMATION
Theseeyebrowlintelkitsaredesignedtoprovideanaestheticallypleasing
appearance and reduces the gap above the fireplace.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
HOMEOWNER'S MANUALS PROVIDED WITH THE APPLIANCE APPLY
TO THESE INSTRUCTIONS.
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Door
Assembly
Bottom Panel
Figure 2 - Glass Door Removal and Reinstallation.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
1
|