|
Quick Start for your WS-7013U
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.
1. Have the indoor station and outdoor remote 3 to 5 apart.
2. Batteries should be out of both units for 10 minutes.
3. Place the batteries into the outdoor remote first then into the indoor station.
(All outdoor remotes must be started before the indoor station)
4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
In this time the display and sensor will start to talk to each other and the display will show both the indoor
temperature and an outdoor temperature. If the station does not display both temperatures after the 10
minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed
for 10 minutes you can place your sensor outdoors and set your time.
The remote sensor should be placed in a dry, shaded area. The remote sensor has a range of 80 feet. Any
walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have
20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus
resistance should not exceed 80 ft. in a straight line.
NOTE: Fog and mist will not harm your remote sensor but direct rain must be avoided.
To complete the set up of your temperature station after the 10 minutes have passed please follow the steps
below.
1. Press and hold the SET button for 5 seconds.
A 12h or 24h will appear on the top line. (12h for AM/PM, 24h for military time)
a. To change between 12h and 24h press and release the MIN/MAX button.
When you have your choice shown on the display press and release the SET button
once.
2. Degree Fahrenheit will now show.
a. To change between Fahrenheit and Celsius, press and release the MIN/MAX button.
When you have your choice shown on the display press and release the SET button
once.
3. An hour will now be flashing.
a. Press and release the MIN/MAX button until the correct hour is shown.
NOTE: When in the 12h mode there is “PM” displayed under the word TIME when in the PM
hours. During the AM hours this area will be blank.
When the correct hour is shown press and release the SET button once.
4. A minute will now be flashing.
a. Press and release the MIN/MAX button until the correct minutes are displayed.
Press and release the SET button once more and you are done.
WS-7013U
Wireless 433 MHz
Temperature Station
Instruction Manual
7
,
0
(
1
nload from Www.Somanuals.com. All Manuals Search And Downl
TABLE OF CONTENTS
Page
Topic
Inventory of Contents
Quick Setup
1
2
Detailed Setup Guide
Battery Installation
Setting the Time
Selecting Units of
Measurement
3-4
5
6
Features
Minimum and Maximum 6-7
Temperatures
Resetting Minimum and
Maximum Temperatures
Additional remote control
senders (optional)
7
7-10
Mounting
Troubleshooting
Maintenance and Care
Specifications
Warranty Information
10-11
12-14
14-15
15-16
17-19
2
nload from Www.Somanuals.com. All Manuals Search And Downl
INVENTORY OF CONTENTS
1. The Indoor Temperature Station (Figure
1)
2. The Remote Control Sensor (TX2U)
and mounting bracket. (Figure 2)
3. 3 each, 1/2” Philips screws.
4. One strip of double sided adhesive tape.
5. Instruction Manual and Warranty Card.
Figure 2
Figure 1
7
,
0
(
ADDITIONAL EQUIPMENT
(not included)
1. 1 Philips screwdriver.
2. 2 Fresh AAA 1.5V batteries.
3. 2 Fresh AAA 1.5V batteries.
1
nload from Www.Somanuals.com. All Manuals Search And Downl
QUICK SETUP
1. Insert two AAA batteries into the
Remote Control Sender.
2. Insert two AAA batteries into the
Indoor Temperature Station.
3. Wait 5-6 minutes, or until the outdoor
temperature is displayed in the
OUTDOOR LCD of the Temperature
Station.
4. Set the Time
5. Mount units.
(See complete instructions for details).
Note: The Remote Control Sender transmits
a signal every 3 minutes. After the batteries
have been installed, the Indoor Temperature
Station searches for these signals for a
duration of 6 minutes. If there is no
temperature reading in the OUTDOOR LCD
after 6 minutes, make sure the units are
within range of each other, or repeat battery
installation process.
2
nload from Www.Somanuals.com. All Manuals Search And Downl
DETAILED SETUP GUIDE
I. BATTERY INSTALLATION
A. REMOTE CONTROL SENDER
Battery cover
Battery compartment
1. Remove the mounting bracket.
2. Remove battery cover
3. Observing the correct polarity, install
2 AAA batteries—make sure they do
not spring free, or start-up problems
may occur. Replace cover.
B. TEMPERATURE STATION
Note: After the batteries are installed, DO
NOT press any buttons. This may interfere
with the signals, causing temperatures to
register incorrectly.
3
nload from Www.Somanuals.com. All Manuals Search And Downl
1. Remove the battery cover on the
backside. To do this, push up and pull
out.
2. Observing
Battery
Cover
the correct
polarity,
install 2 AA
batteries.
3. Replace
battery
cover.
4. Wait 5-6 minutes or until both indoor
and outdoor temperatures are shown
on the Indoor Temperature Station.
5. The Temperature
Station should now
7
,
0
(
show: “-:- -” in the
TIME LCD, and
temperatures in the
INDOOR and
OUTDOOR
LCD’s.
4
nload from Www.Somanuals.com. All Manuals Search And Downl
II. TIME
A. SETTING THE TIME
1. Press and
hold the SET
button for 1
second. “12h”
will appear in the TIME LCD.
2. Use the MIN/MAX button to select
either 12h time (am/pm) or 24h time
3. Press the SET button 2 times, the hour
will flash in the upper left corner.
4. Press the MIN/MAX button to set the
hours, press the SET button, and press
the MIN/MAX button to set the
minutes.
5. Press the SET button to activate the
clock.
Note: When in 12h mode, there is only a
“PM” display, which appears under “TIME.”
If there is no display here it is AM. Make
sure you set the time accordingly.
5
nload from Www.Somanuals.com. All Manuals Search And Downl
III. UNITS OF TEMPERATURE
MEASURE
A. SELECTING UNITS OF
MEASUREMENT
1. Press and hold the SET button for 1
second.
2. Press the SET button again. “°F” will
appear in the TIME LCD.
3. Press the MIN/MAX button to shift
between °F and °C.
4. Press the SET button twice to activate
settings.
IV. FEATURES
A. MINIMUM AND MAXIMUM
TEMPERATURES
1. Press the MIN/MAX button. “MIN”
appears in the temperature LCD’s and
the recorded minimum temperatures
are displayed.
2. Press the MIN/MAX button to toggle
to the maximum temperatures. The
6
nload from Www.Somanuals.com. All Manuals Search And Downl
time of occurrence of the value for
outdoor temperature will also flash.
B. RESETTING THE MINIMUM AND
MAXIMUM TEMPERATURES
1. To reset both the minimum and
maximum temperatures—press and
hold the RESET/+ button for 4
seconds.
C. ADDING ADDITIONAL
REMOTE CONTROL SENDERS
(OPTIONAL)
1. The WS-7013U is able to receive
signals from 3 different Remote
Control Senders. Following are some
brief instructions for the basic set-up
of Remote Control Sender units with
the WS-7013U. These extra sensors
can be purchased through the same
dealer as this unit, or by contacting
La Crosse Technology directly. A
TX2U will monitor temperature only,
a TX3U will monitor temperature and
7
nload from Www.Somanuals.com. All Manuals Search And Downl
display the temperature on its LCD,
and the TX3UP will monitor the
temperature via a probe for use in
pools, spas, etc.
2. Note: When setting up multiple
units it is important to remove the
batteries from all existing units in
operation, then to insert batteries first
into all the Remote Control Sender
units, and in numeric sequence.
Second, install batteries into the
Indoor Temperature Station.
Transmission problems will arise if
this is not done correctly and if the
total time for set-up exceeds 6
minutes.
3. It is necessary to remove the batteries
from all units currently in operation.
4. Remove the battery covers to all
Remote Control Sender units.
5. Place all Remote Control Sender units
in a numeric sequential order.
6. In sequential order, install batteries
(follow the same battery installation
8
nload from Www.Somanuals.com. All Manuals Search And Downl
procedures seen in section I. A) of the
Detailed Set-Up Guide).
7. Install batteries into the Indoor
Temperature Station.
8. Follow the Detailed Set-Up Guide for
programming and operating
instructions.
D. VIEWING AND OPERATING
WITH MULTIPLE REMOTE
CONTROL SENDER UNITS
1. To view the temperature of a different
Remote Control Sender unit, press the
CH button. A shift from one “boxed”
number to the next should be observed
in the OUTDOOR LCD.
2. To view the Minimum/Maximum
temperature: first select from which
Remote Control Sender to read data
(indicated by the “boxed” number).
Pressing the MIN/MAX button will
toggle through the minimum and
maximum indoor temperature, and the
9
nload from Www.Somanuals.com. All Manuals Search And Downl
minimum and maximum outdoor
temperature.
3. To reset the Minimum/Maximum
readings press and the MIN/MAX
button for four seconds.
V. MOUNTING
A. Note: To achieve a true temperature
reading, avoid mounting in direct
sunlight. We recommend that you mount
the Sender on an outside North-facing
wall. The sending range is 80ft;
obstacles such as walls, concrete, and
large metal objects will reduce the range.
Place both units in their desired location
before permanently mounting.
B. REMOTE CONTROL SENDER
1. Remove the mounting bracket from
the Remote Control Sender and mount
with either screws or adhesive tape.
C. THE TEMPERATURE STATION
10
nload from Www.Somanuals.com. All Manuals Search And Downl
1. The Indoor Temperature Station
comes with the table stand already
mounted. If you wish to use the table-
stand, all that is required is to place the
Indoor Temperature Station in an
appropriate location.
2. To wall mount, remove the table
stand. To do this, pull down on the
stand from the rear and rotate forward.
a) Fix a screw (not included) into the
desired wall, and place the
Temperature Station onto the screw
using the hanging hole on the
backside. Gently pull the Station
down to lock the screw into place.
11
nload from Www.Somanuals.com. All Manuals Search And Downl
TROUBLESHOOTING
NOTE: For problems not solved, please
contact La Crosse Technology via e-mail or
phone, or visit our website,
Problem: The LCD is faint
Solution:
1) Replace batteries
Problem: No outdoor temperature is
displayed.
Solution:
1) Remove all batteries, reinsert into sender
first, and then display.
2) Place remote sender closer to display.
3) Be sure all batteries are fresh.
4) Place Remote Control Sender and
Weather Station in position so the
straight-line signal is not passing through
more than two or three walls.
Problem: Temperatures do not match if
units are placed next to each other.
12
nload from Www.Somanuals.com. All Manuals Search And Downl
Solution: Each temperature sensor is
manufactured to be accurate to within 1
degree plus or minus and under normal
conditions; so two sensors could be as much
as 2 degrees different. However, the
difference can be exaggerated further
because the sensors are designed for
different working environments. The indoor
sensor is less responsive to ambient air
currents because of the shielding effect of
the display's case. In addition, the case can
act as a heat sink to absorb and store heat
from external sources (i.e. handling of the
case or radiant heat). In addition, the much
greater range of the outdoor temperature
sensor requires a different calibration curve
than the indoor range. Error is usually
greater at the extreme ends of a range,
making it harder to compare different ranges
with different curves. Under non-laboratory
conditions, it is difficult to compensate for
the above factors and obtain an accurate
comparison.
13
nload from Www.Somanuals.com. All Manuals Search And Downl
MAINTENANCE AND CARE
INSTRUCTIONS
•
•
Extreme temperatures, vibration, and
shock should be avoided to prevent
damage to the units.
Clean displays and units with a soft,
damp cloth. Do not use solvents or
scouring agents; they may mark the
displays and casings.
•
•
Do not submerge in water.
Do not subject the units to unnecessary
heat or cold by placing them in the
oven or freezer.
•
Opening the casings invalidates the
warranty. Do not try to repair the unit.
Contact La Crosse Technology repairs.
14
nload from Www.Somanuals.com. All Manuals Search And Downl
SPECIFICATIONS
Transmitting
433MHz
Frequency
Measuring Temperatures
Temperature
Station: Indoor
32°F to 156.2°F with
0.2°F resolution.
(0°C to 69.0°C with
0.1°C resolution).
Temperature
Station: Outdoor
-21.8 °F to 156.2°F with
0.2°F resolution.
(-29.9°C to 69.0°C with
0.1°C resolution).
Temp accuracy
Transmitting
range
+/- 1°F (+/- .5°C).
Maximum 80 feet (25m)
open space.
Temperature check
Indoor
Outdoor
Every 10 seconds.
Three times in 10
minutes.
Batteries—(Alkaline recommended)
Remote Sender
Temperature
2 x AAA, 1.5V
2 x AA, 1.5V
15
nload from Www.Somanuals.com. All Manuals Search And Downl
Dimensions: (L x W x H)
Temperature
Station
2.75 x .92 x 4.3 in.
(excluding table stand)
(90 x 23.6 x 110 mm).
2.32 x 0.86 x 2.55 in.
(59 x 22 x 65 mm).
Remote Control
Sender
Battery life
Approximately 1 year.
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited
warranty on this product against manufacturing
defects in materials and workmanship.
This limited warranty begins on the original date of
purchase, is valid only on products purchased and
used in North America and only to the original
purchaser of this product. To receive warranty
service, the purchaser must contact La Crosse
Technology, Ltd for problem determination and
service procedures. Warranty service can only be
performed by a La Crosse Technology, Ltd
authorized service center. The original dated bill of
sale must be presented upon request as proof of
purchase to La Crosse Technology, Ltd or La
Crosse Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this
product, at our option and at no charge as stipulated
16
nload from Www.Somanuals.com. All Manuals Search And Downl
herein, with new or reconditioned parts or products if
found to be defective during the limited warranty
period specified above. All replaced parts and
products become the property of La Crosse
Technology, Ltd and must be returned to La Crosse
Technology, Ltd. Replacement parts and products
assume the remaining original warranty, or ninety
(90) days, whichever is longer. La Crosse
Technology, Ltd will pay all expenses for labor and
materials for all repairs covered by this warranty. If
necessary repairs are not covered by this warranty,
or if a product is examined which is not in need or
repair, you will be charged for the repairs or
examination. The owner must pay any shipping
charges incurred in getting your La Crosse
Technology, Ltd product to a La Crosse Technology,
Ltd authorized service center. La Crosse
Technology, Ltd will pay ground return shipping
charges to the owner of the product to a USA
address only.
Your La Crosse Technology, Ltd warranty covers all
defects in material and workmanship with the
following specified exceptions: (1) damage caused
by accident, unreasonable use or neglect (including
the lack of reasonable and necessary maintenance);
(2) damage occurring during shipment (claims must
be presented to the carrier); (3) damage to, or
deterioration of, any accessory or decorative
surface; (4) damage resulting from failure to follow
instructions contained in your owner’s manual; (5)
damage resulting from the performance of repairs or
17
nload from Www.Somanuals.com. All Manuals Search And Downl
alterations by someone other than an authorized La
Crosse Technology, Ltd authorized service center;
(6) units used for other than home use (7)
applications and uses that this product was not
intended or (8) the products inability to receive a
signal due to any source of interference.. This
warranty covers only actual defects within the
product itself, and does not cover the cost of
installation or removal from a fixed installation,
normal set-up or adjustments, claims based on
misrepresentation by the seller or performance
variations resulting from installation-related
circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT
ASSUME LIABILITY FOR INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, OR OTHER
SIMILAR DAMAGES ASSOCIATED WITH THE
OPERATION OR MALFUNCTION OF THIS
PRODUCT. THIS PRODUCT IS NOT TO BE USED
FOR MEDICAL PURPOSES OR FOR PUBLIC
INFORMATION. THIS PRODUCT IS NOT A TOY.
KEEP OUT OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You
may also have other rights specific to your State.
Some States do no allow the exclusion of
consequential or incidental damages therefore the
above exclusion of limitation may not apply to you.
18
nload from Www.Somanuals.com. All Manuals Search And Downl
For warranty work, technical support, or information
contact:
La Crosse Technology
2809 Losey Blvd. S.
La Crosse, WI 54601
Phone: 608.782.1610
Fax: 608.796.1020
e-mail:
(warranty work)
(information on other products)
web:
19
nload from Www.Somanuals.com. All Manuals Search And Downl
FCC DISCLAIMER
This device complies with part 15 of
the FCC rules. Operation is subject to the
following two conditions: (1) this device may not
cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
Freq. 433.92 MHz
La Crosse Technology
Made in China
WS-7013U
FCC ID: OMO-01RX (Receiver)
OMO-01TX (sensor)
20
nload from Www.Somanuals.com. All Manuals Search And Downl
|